[PATCH 4/4] dt-bindings: Add pinctrl bindings for mt65xx/mt81xx.

@@ -0,0 +1,92 @@
+* Mediatek MT65XX Pin Controller
+
+The Mediatek's Pin controller is used to control GPIO pins.
+
+Required properties:
+- compatible: value should be either of the following.
+    (a) "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl.
+- reg: Should contain the register physical address and length for the
+  pin controller.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+  binding is used, the amount of cells must be specified as 2. See the below
+  mentioned gpio binding representation for description of particular cells.
+
+	Eg: <&pio 6 0>
+	<[phandle of the gpio controller node]
+	[pin number within the gpio controller]
+	[flags]>
+
+	Values for gpio specifier:
+	- Pin number: is a value between 0 to 202.
+	- Flags:  bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+            Only the following flags are supported:
+            0 - GPIO_ACTIVE_HIGH
+            1 - GPIO_ACTIVE_LOW
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration and pullups. If one of these options is
+not set, its actual value will be unspecified.
+
+Required subnode-properties:
+
+- mediatek,pinfunc: List of gpio number and function to mux.
+
+The mediatek,pinfunc can use defines directly,
+which are already defind in boot/dts/mt8135-pinfunc.h.
+
+Optional subnode-properties:
+- mediatek,pull: Integer, defines in dt-bindings/pinctrl/mt65xx.h.
+    MT_PIN_PULL_DISABLE: No resistor
+    MT_PIN_CONF_PULL_UP: Pull-up resistor
+    MT_PIN_CONF_PULL_DOWN: Pull-down resistor
+
+The mediatek,pull can be either a single value or an array.
+If it is a single value, that means all pins use use this value for same.
+If it is an array, the means one value per pin.
+
+Examples:
+
+pinctrl at 01c20800 {
+	compatible = "mediatek,mt8135-pinctrl";
+	reg = <0x01c20800 0x400>;
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	i2c0_pins_a: i2c0 at 0 {
+		mediatek,pinfunc = <MT8135_PIN_100_SDA0__FUNC_SDA0 MT8135_PIN_101_SCL0__FUNC_SCL0>;
+		mediatek,pull = <MT_PIN_PULL_DISABLE>;
+	};
+
+	i2c1_pins_a: i2c1 at 0 {
+		mediatek,pinfunc = <MT8135_PIN_195_SDA1__FUNC_SDA1 MT8135_PIN_196_SCL1__FUNC_SCL1>;
+		mediatek,pull = <MT_PIN_PULL_DISABLE>;
+	};
+
+	i2c2_pins_a: i2c2 at 0 {
+		mediatek,pinfunc = <MT8135_PIN_193_SDA2__FUNC_SDA2 MT8135_PIN_194_SCL2__FUNC_SCL2>;
+		mediatek,pull = <MT_PIN_PULL_DISABLE>;
+	};
+
+	i2c3_pins_a: i2c3 at 0 {
+		mediatek,pinfunc = <MT8135_PIN_35_SCL3__FUNC_SCL3 MT8135_PIN_36_SDA3__FUNC_SDA3>;
+		mediatek,pull = <MT_PIN_PULL_DISABLE>;
+	};
+
+	uart2_pins_a: uart2 at 0 {
+		mediatek,pinfunc = <MT8135_PIN_53_URXD2__FUNC_URXD2 MT8135_PIN_54_UTXD2__FUNC_UTXD2>;
+		mediatek,pull = <MT_PIN_PULL_DISABLE>;
+	};
+
+	uart3_pins_a: uart3 at 0 {
+		mediatek,pinfunc = <MT8135_PIN_191_URXD3__FUNC_URXD3 MT8135_PIN_192_UTXD3__FUNC_UTXD3>;
+		mediatek,pull = <MT_PIN_PULL_DISABLE>;
+	};
+	...
+
+};