[PATCH 1/3] Documentation: add Device tree bindings for Hisilicon hip04 ethernet
From: zhangfei.gao@linaro.org (Zhangfei Gao)
Date: 2014-04-01 13:27:10
Also in:
linux-devicetree, netdev
Subsystem:
hisilicon network subsystem driver, networking drivers, open firmware and flattened device tree bindings, the rest · Maintainers:
Jian Shen, Jijie Shao, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
This patch adds the Device Tree bindings for the Hisilicon hip04 Ethernet controller, including 100M / 1000M controller. Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org> --- .../bindings/net/hisilicon-hip04-net.txt | 88 ++++++++++++++++++++ 1 file changed, 88 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
new file mode 100644
index 0000000..988fc69
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt@@ -0,0 +1,88 @@ +Hisilicon hip04 Ethernet Controller + +* Ethernet controller node + +Required properties: +- compatible: should be "hisilicon,hip04-mac". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- port-handle: <phandle port channel> + phandle, specifies a reference to the syscon ppe node + port, port number connected to the controller + channel, recv channel start from channel * number (RX_DESC_NUM) +- phy-mode: see ethernet.txt [1]. + +Optional properties: +- phy-handle: see ethernet.txt [1]. + +[1] Documentation/devicetree/bindings/net/ethernet.txt + + +* Ethernet ppe node: +Control rx & tx fifos of all ethernet controllers. +Have 2048 recv channels shared by all ethernet controllers, only if no overlap. +Each controller's recv channel start from channel * number (RX_DESC_NUM). + +Required properties: +- compatible: "hisilicon,hip04-ppe", "syscon". +- reg: address and length of the register set for the device. + + +* MDIO bus node: + +Required properties: + +- compatible: should be "hisilicon,hip04-mdio". +- Inherits from MDIO bus node binding [2] +[2] Documentation/devicetree/bindings/net/phy.txt + +Example: + mdio { + compatible = "hisilicon,hip04-mdio"; + reg = <0x28f1000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy at 0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + + phy1: ethernet-phy at 1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + }; + + ppe: ppe at 28c0000 { + compatible = "hisilicon,hip04-ppe", "syscon"; + reg = <0x28c0000 0x10000>; + }; + + fe: ethernet at 28b0000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x28b0000 0x10000>; + interrupts = <0 413 4>; + phy-mode = "mii"; + port-handle = <&ppe 31 0>; + }; + + ge0: ethernet at 2800000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2800000 0x10000>; + interrupts = <0 402 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 0 1>; + phy-handle = <&phy0>; + }; + + ge8: ethernet at 2880000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2880000 0x10000>; + interrupts = <0 410 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 8 2>; + phy-handle = <&phy1>; + };
--
1.7.9.5