@@ -0,0 +1,51 @@
+Atmel Image Sensor Interface (ISI) SoC Camera Subsystem
+----------------------------------------------
+
+Required properties:
+- compatible: must be "atmel,at91sam9g45-isi"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the ISI;
+- clocks: list of clock specifiers, corresponding to entries in
+          the clock-names property;
+- clock-names: must contain "isi_clk", which is the isi peripherial clock.
+               "isi_mck" is optinal, it is the master clock output to sensor.
+
+Optional properties:
+- atmel,isi-disable-preview: a boolean property to disable the preview channel;
+
+Example:
+	isi: isi at f0034000 {
+		compatible = "atmel,at91sam9g45-isi";
+		reg = <0xf0034000 0x4000>;
+		interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
+
+		clocks = <&isi_clk>, <&pck1>;
+		clock-names = "isi_clk", "isi_mck";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_isi &pinctrl_pck1_as_isi_mck>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			isi_0: endpoint {
+				remote-endpoint = <&ov2640_0>;
+			};
+		};
+	};
+
+	i2c1: i2c at f0018000 {
+		ov2640: camera at 0x30 {
+			compatible = "omnivision,ov2640";
+			reg = <0x30>;
+
+			port {
+				ov2640_0: endpoint {
+					remote-endpoint = <&isi_0>;
+					bus-width = <8>;
+				};
+			};
+		};
+	};
+

@@ -19,6 +19,7 @@
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 

@@ -33,6 +34,7 @@
 #define VID_LIMIT_BYTES			(16 * 1024 * 1024)
 #define MIN_FRAME_RATE			15
 #define FRAME_INTERVAL_MILLI_SEC	(1000 / MIN_FRAME_RATE)
+#define ISI_DEFAULT_MCLK_FREQ		25000000
 
 /* Frame buffer descriptor */
 struct fbd {

@@ -878,6 +880,22 @@ static int atmel_isi_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static int atmel_isi_probe_dt(struct atmel_isi *isi,
+			struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+
+	isi->pdata.full_mode = !of_property_read_bool(node,
+			"atmel,isi-disable-preview");
+
+	/* Default settings for ISI */
+	isi->pdata.mck_hz = ISI_DEFAULT_MCLK_FREQ;
+	isi->pdata.frate = ISI_CFG1_FRATE_CAPTURE_ALL;
+	isi->pdata.data_width_flags = ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10;
+
+	return 0;
+}
+
 static int atmel_isi_probe(struct platform_device *pdev)
 {
 	unsigned int irq;

@@ -889,7 +907,7 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	struct isi_platform_data *pdata;
 
 	pdata = dev->platform_data;
-	if (!pdata || !pdata->data_width_flags) {
+	if ((!pdata || !pdata->data_width_flags) && !pdev->dev.of_node) {
 		dev_err(&pdev->dev,
 			"No config available for Atmel ISI\n");
 		return -EINVAL;

@@ -905,7 +923,11 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	if (IS_ERR(isi->pclk))
 		return PTR_ERR(isi->pclk);
 
-	memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data));
+	if (pdata)
+		memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data));
+	else	/* dt probe */
+		atmel_isi_probe_dt(isi, pdev);
+
 	isi->active = NULL;
 	spin_lock_init(&isi->lock);
 	INIT_LIST_HEAD(&isi->video_buffer_list);

@@ -1007,11 +1029,18 @@ err_alloc_ctx:
 	return ret;
 }
 
+static const struct of_device_id atmel_isi_of_match[] = {
+	{ .compatible = "atmel,at91sam9g45-isi" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, atmel_isi_of_match);
+
 static struct platform_driver atmel_isi_driver = {
 	.remove		= atmel_isi_remove,
 	.driver		= {
 		.name = "atmel_isi",
 		.owner = THIS_MODULE,
+		.of_match_table = atmel_isi_of_match,
 	},
 };