[PATCH v4 03/22] ARM: Kirkwood: Convert mv88f6281gtw_ge switch setup to DT

@@ -122,4 +122,66 @@
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	dsa at 0 {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth0>;
+		dsa,mii-bus = <&ethphy0>;
+
+		switch at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0>;	/* MDIO address 0, switch 0 in tree */
+
+			port at 0 {
+				reg = <0>;
+				label = "lan1";
+			};
+
+			port at 1 {
+				reg = <1>;
+				label = "lan2";
+			};
+
+			port at 2 {
+				reg = <2>;
+				label = "lan3";
+			};
+
+			port at 3 {
+				reg = <3>;
+				label = "lan4";
+			};
+
+			port at 4 {
+				reg = <4>;
+				label = "wan";
+			};
+
+			port at 5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at ff {
+		reg = <0xff>; 	/* No phy attached */
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
 };

@@ -106,13 +106,6 @@ config ARCH_KIRKWOOD_DT
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Kirkwood using flattened device tree.
 
-config MACH_MV88F6281GTW_GE_DT
-	bool "Marvell 88F6281 GTW GE Board (Flattened Device Tree)"
-	depends on ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell 88F6281 GTW GE Board (Flattened Device Tree).
-
 endmenu
 
 endif

@@ -13,4 +13,3 @@ obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o tsx1x-common.o
 obj-$(CONFIG_MACH_TS41X)		+= ts41x-setup.o tsx1x-common.o
 
 obj-$(CONFIG_ARCH_KIRKWOOD_DT)		+= board-dt.o
-obj-$(CONFIG_MACH_MV88F6281GTW_GE_DT)	+= board-mv88f6281gtw_ge.o

@@ -131,9 +131,6 @@ static void __init kirkwood_dt_init(void)
 	kexec_reinit = kirkwood_enable_pcie;
 #endif
 
-	if (of_machine_is_compatible("marvell,mv88f6281gtw-ge"))
-		mv88f6281gtw_ge_init();
-
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 

@@ -1,50 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
- *
- * Marvell 88F6281 GTW GE Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/timer.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/ethtool.h>
-#include <linux/gpio.h>
-#include <net/dsa.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data mv88f6281gtw_ge_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_NONE,
-	.speed		= SPEED_1000,
-	.duplex		= DUPLEX_FULL,
-};
-
-static struct dsa_chip_data mv88f6281gtw_ge_switch_chip_data = {
-	.port_names[0]	= "lan1",
-	.port_names[1]	= "lan2",
-	.port_names[2]	= "lan3",
-	.port_names[3]	= "lan4",
-	.port_names[4]	= "wan",
-	.port_names[5]	= "cpu",
-};
-
-static struct dsa_platform_data mv88f6281gtw_ge_switch_plat_data = {
-	.nr_chips	= 1,
-	.chip		= &mv88f6281gtw_ge_switch_chip_data,
-};
-
-void __init mv88f6281gtw_ge_init(void)
-{
-	kirkwood_ge00_init(&mv88f6281gtw_ge_ge00_data);
-	kirkwood_ge00_switch_init(&mv88f6281gtw_ge_switch_plat_data, NO_IRQ);
-}

@@ -58,13 +58,6 @@ void kirkwood_cpufreq_init(void);
 void kirkwood_restart(enum reboot_mode, const char *);
 void kirkwood_clk_init(void);
 
-/* board init functions for boards not fully converted to fdt */
-#ifdef CONFIG_MACH_MV88F6281GTW_GE_DT
-void mv88f6281gtw_ge_init(void);
-#else
-static inline void mv88f6281gtw_ge_init(void) {};
-#endif
-
 /* early init functions not converted to fdt yet */
 char *kirkwood_id(void);
 void kirkwood_l2_init(void);