[PATCH V2 1/6] ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN

From
Shawn Guo <hidden>
Date
2013-11-25 07:13:00
Also in
linux-ide
Reply to
Troy Kisky, 2013-11-22
On Fri, Nov 22, 2013 at 12:26:45PM -0700, Troy Kisky wrote:
On 11/22/2013 4:04 AM, Marek Vasut wrote:
quoted
We must clear this IMX6Q_GPR13_SATA_MPLL_CLK_EN bit on i.MX6Q, otherwise
Linux will fail to find the attached drive on some boards.

This entire fix was:
Reported-by: Eric Nelson <redacted>

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <redacted>
Cc: Richard Zhu <redacted>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <redacted>
---
 drivers/ata/ahci_imx.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

V2: Update the value in the comment from 0x7ffffffd to 0x7ffffffe
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index ae2d73f..14227d1 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -113,7 +113,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
 	/*
 	 * set PHY Paremeters, two steps to configure the GPR13,
 	 * one write for rest of parameters, mask of first write
-	 * is 0x07fffffd, and the other one write for setting
+	 * is 0x07fffffe, and the other one write for setting
0x07ffffff, d+2 = f,
bit 1 is IMX6Q_GPR13_SATA_MPLL_CLK_EN, which you just added
bit 0 is IMX6Q_GPR13_SATA_TX_EDGE_RATE, which is also in your expression
Ah, sorry.  The mistake comes from my wrong bit math.

Shawn
quoted
 	 * the mpll_clk_en.
 	 */
 	regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
@@ -125,6 +125,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
 			| IMX6Q_GPR13_SATA_TX_BOOST_MASK
 			| IMX6Q_GPR13_SATA_TX_LVL_MASK
 			| IMX6Q_GPR13_SATA_TX_EDGE_RATE
+			| IMX6Q_GPR13_SATA_MPLL_CLK_EN
 			, IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB
 			| IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M
 			| IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
Thread (10 messages) 10 messages, 3 authors, last reply 2013-11-25
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help