mxsfb: DATA_FORMAT_24_BIT flag outputs invalid colours

Hi Maxime,

maxime.ripard at free-electrons.com wrote:

On Thu, May 23, 2013 at 01:55:28PM +0200, Hector Palacios wrote:

quoted

I'm using an i.MX28 based board with lcd connected with 18bits data bus.
My platform uses 32 bits per pixel:

	mxsfb_pdata.default_bpp = 32;
	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;

With these settings the mxsfb.c driver sets flag DATA_FORMAT_24_BIT
at HW_LCDIF_CTRL register in function mxsfb_set_par():

	case 32:
		dev_dbg(&host->pdev->dev, "Setting up RGB888/666 mode\n");
		ctrl |= CTRL_SET_WORD_LENGTH(3);
		switch (host->ld_intf_width) {
		case STMLCDIF_8BIT:
			dev_dbg(&host->pdev->dev,
					"Unsupported LCD bus width mapping\n");
			return -EINVAL;
		case STMLCDIF_16BIT:
		case STMLCDIF_18BIT:
			/* 24 bit to 18 bit mapping */
			ctrl |= CTRL_DF24; /* ignore the upper 2 bits in
					    *  each colour component
					    */
			break;
		case STMLCDIF_24BIT:
			/* real 24 bit */
			break;
		}

According to the manual, this flag does:
	0x0: ALL_24_BITS_VALID: Data input to the block is in 24 bpp
format, such that all RGB 888 data is contained in 24 bits.
	0x1: DROP_UPPER_2_BITS_PER_BYTE ? Data input to the block is
actually RGB 18 bpp, but there is 1 colour per byte, hence the upper
2 bits in each byte do not contain any useful data, and should be
dropped.

The setting of this flag is producing bad colours with true colour
images (i.e. the Linux penguin is displayed ok, but QT applications
or images displayed with fbv are not).
I believe the setting of this flag is not correct (after all, if my
bpp is 32, then all 24bit colours are useful and dropping the upper
2 bits is a bad idea).
If I don't set it, then true colour images are displayed correctly.
The only problem is that the Linux penguin is displayed much darker
than usual (correct colours, but darker). Perhaps the 224 colour
format of this image justifies it?

I noticed the cfa10049 platform also uses the same configuration (18
bits data bus and 32bpp) and was wondering if true colour images are
correctly displayed in this platform with this flag set (for example
with fbv application [1]).

I had the exact same problem, and suggested the exact same solution a
few weeks back.

https://patchwork.kernel.org/patch/2470441/

The conclusion of that discussion what that the userspace applications
were not honouring the bitfield correctly set by the mxsfb driver, and
as such, it was not a bug in the driver.

While this is correct, I wonder, now that since we had that same problem
in a very short amount of time, if we couldn't set this behaviour
dependant of some (dt? kernel argument?) property so that one could
customise it anyway he want.

Maxime

i.MX2[3|8]    LCD1       LCD2       LCD3
              24bit      18bit      18bit
--------------------------------------------
LCD_D0         B0         B0         --
LCD_D1         B1         B1         --
LCD_D2         B2         B2         B0
LCD_D3         B3         B3         B1
LCD_D4         B4         B4         B2
LCD_D5         B5         B5         B3
LCD_D6         B6         G0         B4
LCD_D7         B7         G1         B5

LCD_D8         G0         G2         --
LCD_D9         G1         G3         --
LCD_D10        G2         G4         G0
LCD_D11        G3         G5         G1
LCD_D12        G4         R0         G2
LCD_D13        G5         R1         G3
LCD_D14        G6         R2         G4
LCD_D15        G7         R3         G5

LCD_D16        R0         R4         --
LCD_D17        R1         R5         --
LCD_D18        R2                    R0
LCD_D19        R3                    R1
LCD_D20        R4                    R2
LCD_D21        R5                    R3
LCD_D22        R6                    R4
LCD_D23        R7                    R5

Is your display connected like LCD2 or LCD3? LCD3 must still handled like a 24 
bit display shown in LCD1, while only the LCD2-case is the "24 bit to 18 bit 
mapping" case.

At least my current tests with an i.MX23 and a connection like LCD2 are 
working here with a Qt application. Qt honours the pixel bitfield 
description. And I'm using the "bits-per-pixel = <32>" and "bus-width = <18>" 
entries in the device tree.

Regards,
Juergen

-- 
Pengutronix e.K.                              | Juergen Beisert             |
Linux Solutions for Science and Industry      | http://www.pengutronix.de/  |