Thread (96 messages) 96 messages, 15 authors, 2013-05-31

[PATCH v4 06/12] ARM: dove: add gigabit ethernet and mvmdio device tree nodes

From: andrew@lunn.ch (Andrew Lunn)
Date: 2013-05-21 17:49:08
Also in: linuxppc-dev, lkml, netdev

On Tue, May 21, 2013 at 06:41:44PM +0200, Sebastian Hesselbarth wrote:
quoted hunk ↗ jump to hunk
This patch adds orion-eth and mvmdio device tree nodes for DT enabled
Dove boards. As there is only one ethernet controller on Dove, a default
phy node is also added with a note to set its reg property on a per-board
basis.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v3->v4:
- convert to new device tree binding

Cc: David Miller <davem@davemloft.net>
Cc: Lennert Buytenhek <redacted>
Cc: Jason Cooper <redacted>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: netdev at vger.kernel.org
Cc: linux-arm-kernel at lists.infradead.org
Cc: linuxppc-dev at lists.ozlabs.org
Cc: linux-kernel at vger.kernel.org
---
 arch/arm/boot/dts/dove-cubox.dts |    7 +++++++
 arch/arm/boot/dts/dove.dtsi      |   35 +++++++++++++++++++++++++++++++++++
 2 files changed, 42 insertions(+)
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index 7e3065a..02618fa 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -49,6 +49,13 @@
 &uart0 { status = "okay"; };
 &sata0 { status = "okay"; };
 &i2c0 { status = "okay"; };
+&mdio { status = "okay"; };
+&eth { status = "okay"; };
+
+&ethphy {
+	compatible = "marvell,88e1310";
+	reg = <1>;
+};
 
 &sdio0 {
 	status = "okay";
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 6cab468..8612658 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -258,5 +258,40 @@
 				dmacap,xor;
 			};
 		};
+
+		mdio: mdio-bus at 72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <30>;
+			clocks = <&gate_clk 2>;
+			status = "disabled";
+
+			ethphy: ethernet-phy {
+				device-type = "ethernet-phy";
+				/* set phy address in board file */
+			};
+		};
+
+		eth: ethernet-controller at 72000 {
+			compatible = "marvell,orion-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			clocks = <&gate_clk 2>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet-port at 0 {
+				device_type = "network";
+				compatible = "marvell,orion-eth-port";
+				reg = <0>;
+				interrupts = <29>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
Hi Sebastian

Its probably a good idea to set the local administration bit in this
MAC address. i.e. first byte is 02.

    Andrew
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help