@@ -18,8 +18,8 @@
 #include <linux/list.h>
 #include <linux/clk.h>
 #include <plat/clkdev_omap.h>
-#include <plat/am33xx.h>
 
+#include "am33xx.h"
 #include "iomap.h"
 #include "control.h"
 #include "clock.h"

@@ -21,7 +21,7 @@
 #include <mach/ctrl_module_pad_core_44xx.h>
 #include <mach/ctrl_module_pad_wkup_44xx.h>
 
-#include <plat/am33xx.h>
+#include "am33xx.h"
 
 #ifndef __ASSEMBLY__
 #define OMAP242X_CTRL_REGADDR(reg)					\

@@ -50,9 +50,8 @@
 #include <asm/suspend.h>
 #include <asm/hardware/cache-l2x0.h>
 
-#include <plat/omap44xx.h>
-
 #include "common.h"
+#include "omap44xx.h"
 #include "omap4-sar-layout.h"
 #include "pm.h"
 #include "prcm_mpu44xx.h"

@@ -1,6 +1,4 @@
 /*
- * arch/arm/plat-omap/include/mach/omap24xx.h
- *
  * This file contains the processor specific definitions
  * of the TI OMAP24XX.
  *

@@ -1,6 +1,4 @@
 /*
- * arch/arm/plat-omap/include/mach/omap34xx.h
- *
  * This file contains the processor specific definitions of the TI OMAP34XX.
  *
  * Copyright (C) 2007 Texas Instruments.

@@ -28,8 +28,7 @@
 #include <linux/linkage.h>
 #include <asm/assembler.h>
 
-#include <plat/omap24xx.h>
-
+#include "omap24xx.h"
 #include "sdrc.h"
 
 /* First address of reserved address space?  apparently valid for OMAP2 & 3 */

@@ -26,9 +26,9 @@
 
 #include <asm/assembler.h>
 
-#include <plat/omap34xx.h>
 #include <plat/sram.h>
 
+#include "omap34xx.h"
 #include "iomap.h"
 #include "cm2xxx_3xxx.h"
 #include "prm2xxx_3xxx.h"

@@ -14,10 +14,10 @@
 #include <asm/memory.h>
 #include <asm/hardware/cache-l2x0.h>
 
-#include <plat/omap44xx.h>
 #include <mach/omap-secure.h>
 
 #include "common.h"
+#include "omap44xx.h"
 #include "omap4-sar-layout.h"
 
 #if defined(CONFIG_SMP) && defined(CONFIG_PM)

@@ -1,7 +1,7 @@
 #include <plat/cpu.h>
-#include <plat/omap24xx.h>
-#include <plat/omap34xx.h>
-#include <plat/omap44xx.h>
-#include <plat/ti81xx.h>
-#include <plat/am33xx.h>
-#include <plat/omap54xx.h>
+#include "omap24xx.h"
+#include "omap34xx.h"
+#include "omap44xx.h"
+#include "ti81xx.h"
+#include "am33xx.h"
+#include "omap54xx.h"

@@ -3,8 +3,7 @@
 #
 
 # Common support
-obj-y := common.o sram.o clock.o devices.o dma.o mux.o \
-	 fb.o counter_32k.o
+obj-y := common.o sram.o clock.o dma.o mux.o fb.o counter_32k.o
 obj-m :=
 obj-n :=
 obj-  :=

@@ -1,91 +0,0 @@
-/*
- * linux/arch/arm/plat-omap/devices.c
- *
- * Common platform device setup/initialization for OMAP1 and OMAP2
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#include <linux/gpio.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/slab.h>
-#include <linux/memblock.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/map.h>
-#include <asm/memblock.h>
-
-#include <plat/tc.h>
-#include <plat/mmc.h>
-#include <plat/menelaus.h>
-#include <plat/omap44xx.h>
-
-/*-------------------------------------------------------------------------*/
-
-#if defined(CONFIG_HW_RANDOM_OMAP) || defined(CONFIG_HW_RANDOM_OMAP_MODULE)
-
-#ifdef CONFIG_ARCH_OMAP2
-#define	OMAP_RNG_BASE		0x480A0000
-#else
-#define	OMAP_RNG_BASE		0xfffe5000
-#endif
-
-static struct resource rng_resources[] = {
-	{
-		.start		= OMAP_RNG_BASE,
-		.end		= OMAP_RNG_BASE + 0x4f,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device omap_rng_device = {
-	.name		= "omap_rng",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(rng_resources),
-	.resource	= rng_resources,
-};
-
-static void omap_init_rng(void)
-{
-	(void) platform_device_register(&omap_rng_device);
-}
-#else
-static inline void omap_init_rng(void) {}
-#endif
-
-/*
- * This gets called after board-specific INIT_MACHINE, and initializes most
- * on-chip peripherals accessible on this board (except for few like USB):
- *
- *  (a) Does any "standard config" pin muxing needed.  Board-specific
- *	code will have muxed GPIO pins and done "nonstandard" setup;
- *	that code could live in the boot loader.
- *  (b) Populating board-specific platform_data with the data drivers
- *	rely on to handle wiring variations.
- *  (c) Creating platform devices as meaningful on this board and
- *	with this kernel configuration.
- *
- * Claiming GPIOs, and setting their direction and initial values, is the
- * responsibility of the device drivers.  So is responding to probe().
- *
- * Board-specific knowledge like creating devices or pin setup is to be
- * kept out of drivers as much as possible.  In particular, pin setup
- * may be handled by the boot loader, and drivers should expect it will
- * normally have been done by the time they're probed.
- */
-static int __init omap_init_devices(void)
-{
-	/* please keep these calls, and their implementations above,
-	 * in alphabetical order so they're easier to sort through.
-	 */
-	omap_init_rng();
-	return 0;
-}
-arch_initcall(omap_init_devices);