[PATCH 2/2] ARM: dts: AM33XX: Add lis331dlh device tree data to am335x-evm

Hi Arnd,

Thanks for the review,

On Fri, Sep 14, 2012 at 13:56:06, Arnd Bergmann wrote:

On Thursday 13 September 2012, AnilKumar Ch wrote:

quoted

Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status to "okay" to use I2C2 bus. Also added all the
required platform data to am335x-evm.

Signed-off-by: AnilKumar Ch <redacted>
---
 arch/arm/boot/dts/am335x-evm.dts |   42 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index 9fb59c5..9e5a878 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts

@@ -47,6 +47,15 @@
 			};
 		};
 
+		i2c2: i2c at 4802a000 {
+			status = "okay";
+			clock-frequency = <400000>;
+
+			lis331dlh: lis331dlh at 18 {
+				reg = <0x18>;
+			};
+		};

Why do you put the "reg" property here

Here I specified reg property because lis331dlh I2C slave address is 0x18.

quoted

 		dcan1: d_can at 481d0000 {
 			status = "okay";
 			pinctrl-names = "default";

@@ -61,6 +70,39 @@
 		regulator-max-microvolt = <5000000>;
 		regulator-boot-on;
 	};
+
+	lis3_reg: fixedregulator at 1 {
+		compatible = "regulator-fixed";
+		regulator-name = "lis3_reg";
+		regulator-boot-on;
+	};
+};
+&lis331dlh {
+	compatible = "st,lis3lv02d-i2c";

and all the rest here? At least I would expect the "compatible" property
to be in the same place above.

This data is appended to above one, to make it readable I moved remaining
properties to here.

Also, I think you should remove the "-i2c" postfix from the name, that
is already implied by the parent bus.

I will remove, but in case of spi the compatible name is lis3lv02d_spi.
By mistake I have uses "-i2c" instead of "_i2c".

quoted

+	Vdd-supply = <&lis3_reg>;
+	Vdd_IO-supply = <&lis3_reg>;
+
+	st,click-single-x;
+	st,click-single-y;
+	st,click-single-z;
+	st,click-thresh-x = <10>;
+	st,click-thresh-y = <10>;
+	st,click-thresh-z = <10>;
+	st,irq1-click;
+	st,irq2-click;
+	st,wakeup-x-lo;
+	st,wakeup-x-hi;
+	st,wakeup-y-lo;
+	st,wakeup-y-hi;
+	st,wakeup-z-lo;
+	st,wakeup-z-hi;
+	st,min-limit-x = <120>;
+	st,min-limit-y = <120>;
+	st,min-limit-z = <140>;
+	st,max-limit-x = <550>;
+	st,max-limit-y = <550>;
+	st,max-limit-z = <750>;

Is there a binding document that describes all these?

Document is already present, 
http://git.kernel.org/?p=linux/kernel/git/next/linux-next.git;a=commit;h=2f2ff3cc8d930493f9a598b9192706c09403e12e

Some minor changes in docs, in my next version I will update document
as well. I will send V3 if there are no comments on v2.

Thanks
AnilKumar