[PATCH] efikamx: reintroduce Genesi Efika MX Smarttop via device tree
From: Shawn Guo <hidden>
Date: 2012-08-08 15:15:34
Also in:
lkml
On Tue, Aug 07, 2012 at 04:46:18PM -0500, Matt Sealey wrote:
quoted hunk ↗ jump to hunk
This device tree only supports the final retail board ("TO3"). It is currently feature equivalent to the MX51 Babbage device tree. The following features have been tested and work as well as can be expected: * Serial port * SD card support * I2C bus * SGTL5000 audio support via the internal speaker * SDMA support (via audio) * SPI bus * NOR flash (at 25MHz bus speed) * MC13892 PMIC Regulator and Realtime clock functions Since the board requires some extra work on the PMIC to power off, the system will instead just halt, however reboot works. Other missing features are due to a lack of drivers or device tree bindings currently. Signed-off-by: Matt Sealey <redacted> Signed-off-by: Steev Klimaszewski <redacted> --- arch/arm/boot/dts/imx51-efikamx.dts | 247 +++++++++++++++++++++++++++++++++++ arch/arm/mach-imx/Makefile.boot | 2 +- 2 files changed, 248 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx51-efikamx.dtsdiff --git a/arch/arm/boot/dts/imx51-efikamx.dts b/arch/arm/boot/dts/imx51-efikamx.dts new file mode 100644 index 0000000..dd14f77 --- /dev/null +++ b/arch/arm/boot/dts/imx51-efikamx.dts@@ -0,0 +1,247 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * Copyright 2012 Genesi USA, Inc. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx51.dtsi" + +/ { + model = "Genesi Efika MX (Smarttop)"; + compatible = "genesi,imx51-efikamx", "fsl,imx51"; + + memory { + reg = <0x90000000 0x20000000>; + }; + + soc { + aips at 70000000 { + spba at 70000000 { + esdhc at 70004000 {
The pinctrl_provide_dummies() in imx51_dt_init() is something to be removed. Then any driver calling pinctrl API will require pinctrl set up for the device here. So please have the pinctrl setup for those devices.
+ cd-gpios = <&gpio1 0 0>;
+ wp-gpios = <&gpio1 1 0>;
+ status = "okay";
+ };
+
+ ssi2: ssi at 70014000 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+ };
+
+ ecspi at 70010000 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio4 24 0>, <&gpio4 25 0>;
+ status = "okay";
+
+ pmic: mc13892 at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mc13892";
+ spi-max-frequency = <6000000>;
+ reg = <0>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <6 0x4>;
+ fsl,mc13xxx-uses-rtc;
+
+ regulators {
+ sw1_reg: sw1 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1375000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vpll_reg: vpll {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdig_reg: vdig {
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ };
+
+ vsd_reg: vsd {
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ };
+
+ vusb2_reg: vusb2 {
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <2775000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vvideo_reg: vvideo {
+ regulator-min-microvolt = <2775000>;
+ regulator-max-microvolt = <2775000>;
+ regulator-boot-on;
+ };
+
+ vaudio_reg: vaudio {
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vcam_reg: vcam {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3150000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ flash: sst25vf032b at 1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25vf032b";
+ spi-max-frequency = <25000000>;
+ reg = <1>;
+
+ partition at 0 {
+ label = "firmware";
+ reg = <0x0 0x200000>;
+ };
+
+ partition at 200000 {
+ label = "user";
+ reg = <0x200000 0x200000>;
+ };
+ };
+ };
+ };
+
+ wdog at 73f98000 {
+ status = "okay";
+ };Remove it. I have queued a patch to enable wdog in <soc>.dtsi by default.
+
+ iomuxc at 73fa8000 {
+ compatible = "fsl,imx51-iomuxc";
+ reg = <0x73fa8000 0x4000>;
+ };
+
+ uart1: serial at 73fbc000 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+ };
+
+ };
+
+ aips at 80000000 {
+ sdma at 83fb0000 {
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx51.bin";
+ };Remove it. I have seen a patch to move this name into <soc>.dtsi as default.
quoted hunk ↗ jump to hunk
+ + i2c at 83fc4000 { + status = "okay"; + + codec: sgtl5000 at 0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clock-frequency = <12288000>; + VDDA-supply = <&vdig_reg>; + VDDIO-supply = <&vvideo_reg>; + }; + }; + + audmux at 83fd0000 { + status = "okay"; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power Button"; + gpios = <&gpio2 31 0>; + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + red { + label = "red"; + gpios = <&gpio3 13>; + linux,default-trigger = "ide-disk"; + }; + + green { + label = "green"; + gpios = <&gpio3 14>; + linux,default-trigger = "default-on"; + }; + + blue { + label = "blue"; + gpios = <&gpio3 15>; + linux,default-trigger = "mmc0"; + }; + }; + + sound { + compatible = "fsl,imx-audio-sgtl5000"; + model = "efikamx-sgtl5000"; + ssi-controller = <&ssi2>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Ext Spk", "LINE_OUT"; + audio-codec = <&codec>; + mux-int-port = <2>; + mux-ext-port = <3>; + }; +};diff --git a/arch/arm/mach-imx/Makefile.boot b/arch/arm/mach-imx/Makefile.boot index 05541cf..3ed7c9d 100644 --- a/arch/arm/mach-imx/Makefile.boot +++ b/arch/arm/mach-imx/Makefile.boot@@ -38,7 +38,7 @@ zreladdr-$(CONFIG_SOC_IMX6Q) += 0x10008000 params_phys-$(CONFIG_SOC_IMX6Q) := 0x10000100 initrd_phys-$(CONFIG_SOC_IMX6Q) := 0x10800000 -dtb-$(CONFIG_MACH_IMX51_DT) += imx51-babbage.dtb +dtb-$(CONFIG_MACH_IMX51_DT) += imx51-babbage.dtb imx51-efikamx.dtb
Please have the new entry on the new line like dtb-$(CONFIG_SOC_IMX6Q). Yes, we will change dtb-$(CONFIG_MACH_IMX53_DT).
dtb-$(CONFIG_MACH_IMX53_DT) += imx53-ard.dtb imx53-evk.dtb \ imx53-qsb.dtb imx53-smd.dtb dtb-$(CONFIG_SOC_IMX6Q) += imx6q-arm2.dtb \ -- 1.7.9.5
-- Regards, Shawn