[PATCH 00/08] mach-shmobile: Emma Mobile EV2 support V3

Hi Magnus,

I have tested these patches on top of the soc-new branch of
rafael's renesas tree, revision 5658c94, which is based on
v3.4-rc6.

I also have the cherry picked following patches before applying your patches.

serial8250-em: clk_get() IS_ERR() error handling fix
serial8250-em: Emma Mobile UART driver V2
serial8250: Introduce serial8250_register_8250_port()
serial8250: Clean up default map and dl code
serial8250: Use dl_read()/dl_write() on RM9K
serial8250: Use dl_read()/dl_write() on Alchemy
serial8250: Add dl_read()/dl_write() callbacks
8250.c: less than 2400 baud fix.
serial/8250_pci: Clear FIFOs for Intel ME Serial Over Lan device on BI
tegra, serial8250: add ->handle_break() uart_port op
clocksource: em_sti: Add DT support
clocksource: em_sti: Emma Mobile STI driver V2
clockevents: Make clockevents_config() a global symbol

I have added the follwing patch of yours

gpio: Emma Mobile GPIO driver V2

And one of my own, which just fixes a build problem
in rafael's tree.

ARM: mach-types: Manually add KZM-A9-GT

On Wed, May 16, 2012 at 03:44:49PM +0900, Magnus Damm wrote:

mach-shmobile: Emma Mobile EV2 support V3

[PATCH 01/08] mach-shmobile: Emma Mobile EV2 SoC base support V3

Tested-by: Simon Horman <horms@verge.net.au>

[PATCH 02/08] ARM: Undelete KZM9D mach-type V3

I did not need this patch with the base I am using,
so I did not test it.

Reviewed-by: Simon Horman <horms@verge.net.au>

[PATCH 03/08] mach-shmobile: KZM9D board support V3

Tested-by: Simon Horman <horms@verge.net.au>

[PATCH 04/08] mach-shmobile: Emma Mobile EV2 SMP support V3

Tested-by: Simon Horman <horms@verge.net.au>

[PATCH 05/08] mach-shmobile: Emma Mobile EV2 GPIO support V3

I am only seeing interripts for em_gio.0, is there a
way to exercise em_gio.1 .. 4 ?

Duplicate names for interrupts, that is
each of em_gio.0..4 have two entries in /proc/interripts.
Is this intentional?

 99:         32          0       GIC  em_gio.0
 100:          0          0       GIC  em_gio.0
 101:          0          0       GIC  em_gio.1
 102:          0          0       GIC  em_gio.1
 103:          0          0       GIC  em_gio.2
 104:          0          0       GIC  em_gio.2
 105:          0          0       GIC  em_gio.3
 106:          0          0       GIC  em_gio.3
 107:          0          0       GIC  em_gio.4
 108:          0          0       GIC  em_gio.4
 157:      35952          0       GIC  em_sti.0

[PATCH 06/08] mach-shmobile: KZM9D board Ethernet support V3

Tested-by: Simon Horman <horms@verge.net.au>

[PATCH 07/08] mach-shmobile: Emma Mobile EV2 DT support V3

I applied this and the resulting kernel booted.

[PATCH 08/08] mach-shmobile: Use DT_MACHINE for KZM9D V3

I applied this and the resulting kernel did not boot.
I saw nothing after the uboot prompt..


Lastly, could you consider suppling a patch which provides a defconfig?