[PATCH 1/2] gpio: add a driver for the Synopsys DesignWare APB GPIO block

The Synopsys DesignWare block is used in some ARM devices (picoxcell)
and can be configured to provide multiple banks of GPIO pins.  The first
bank (A) can also provide IRQ capabilities.

Cc: Grant Likely <redacted>
Cc: Linus Walleij <redacted>
Cc: Rob Herring <redacted>
Signed-off-by: Jamie Iles <redacted>
---

I was originally working on a generic binding for the generic gpio
driver, but this doesn't scale well when there are interrupt
capabilities in the controller, so here's a driver specifically for the
Synopsys block.

 .../devicetree/bindings/gpio/snps-dwapb-gpio.txt   |   63 ++++
 drivers/gpio/Kconfig                               |   10 +
 drivers/gpio/Makefile                              |    1 +
 drivers/gpio/gpio-dwapb.c                          |  337 ++++++++++++++++++++
 4 files changed, 411 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
 create mode 100644 drivers/gpio/gpio-dwapb.c

diff --git a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
new file mode 100644
index 0000000..62943fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt

@@ -0,0 +1,63 @@
+* Synopsys DesignWare APB GPIO controller
+
+Required properties:
+- compatible : Should be "snps,dw-apb-gpio"
+- reg : Address and length of the register set for the device
+
+The GPIO controller has a configurable number of banks, each of which are
+represented as child nodes with the following properties:
+
+Required properties:
+- compatible : "snps,dw-apb-gpio-bank"
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- snps,gpio-bank : The integer bank index of the bank, a single cell.

+
+Optional properties:
+- interrupt-controller : The first bank may be configured to be an interrupt
+controller.
+- #interrupt-cells : Specifies the number of cells needed to encode an
+interrupt.  Shall be set to 2.  The first cell defines the interrupt number,
+the second encodes the triger flags encoded as:
+
+	bits[3:0] trigger type and level flags.
+		1 = low-to-high edge triggered
+		2 = high-to-low edge triggered
+		4 = active high level-sensitive
+		8 = active low level-sensitive
+
+- interrupt-parent : The parent interrupt controller.
+- interrupts : The interrupts to the parent controller raised when GPIOs
+generate the interrupts.
+
+Example:
+
+gpio: gpio at 20000 {
+	compatible = "snps,dw-apb-gpio";
+	reg = <0x20000 0x1000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	banka: gpio-controller at 0 {
+		compatible = "snps,dw-apb-gpio-bank";
+		gpio-controller;
+		#gpio-cells = <2>;
+		nr-gpio = <8>;
+		snps,gpio-bank = <0>
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&vic1>;
+		interrupts = <0 1 2 3 4 5 6 7>;
+	};
+
+	bankb: gpio-controller at 1 {
+		compatible = "snps,dw-apb-gpio-bank";
+		gpio-controller;
+		#gpio-cells = <2>;
+		nr-gpio = <8>;
+		snps,gpio-bank = <1>
+	};
+};

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 573532f..93fd69d 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig

@@ -85,6 +85,16 @@ config GPIO_GENERIC_PLATFORM
 	help
 	  Say yes here to support basic platform_device memory-mapped GPIO controllers.
 
+config GPIO_DWAPB
+	bool "Synopsys DesignWare APB GPIO driver"
+	select GPIO_GENERIC
+	select GENERIC_IRQ_CHIP
+	select IRQ_DOMAIN