@@ -70,6 +70,7 @@ static struct at91_eth_data __initdata onearm_eth_data = {
 
 static struct at91_usbh_data __initdata onearm_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata onearm_udc_data = {

@@ -75,6 +75,7 @@ static void __init afeb9260_init_early(void)
  */
 static struct at91_usbh_data __initdata afeb9260_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -82,7 +83,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = {
  */
 static struct at91_udc_data __initdata afeb9260_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -143,6 +144,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
 	.bus_width_16	= 0,
+	.det_pin	= -1,
 };
 
 

@@ -154,6 +156,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
 	.wp_pin 	= AT91_PIN_PC4,
 	.slot_b		= 1,
 	.wire4		= 1,
+	.vcc_pin	= -1,
 };
 
 

@@ -174,6 +177,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
 static struct at91_cf_data afeb9260_cf_data = {
 	.chipselect = 4,
 	.irq_pin    = AT91_PIN_PA6,
+	.det_pin	= -1,
+	.vcc_pin	= -1,
 	.rst_pin    = AT91_PIN_PA7,
 	.flags      = AT91_CF_TRUE_IDE,
 };

@@ -62,6 +62,7 @@ static void __init cam60_init_early(void)
  */
 static struct at91_usbh_data __initdata cam60_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 

@@ -141,7 +142,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata cam60_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-	// .det_pin	= ... not there
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PA9,
 	.enable_pin	= AT91_PIN_PA7,
 	.partition_info	= nand_partitions,

@@ -70,6 +70,7 @@ static void __init cap9adk_init_early(void)
  */
 static struct at91_usbh_data __initdata cap9adk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -144,9 +145,9 @@ static struct spi_board_info cap9adk_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata cap9adk_mmc_data = {
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 

@@ -154,6 +155,7 @@ static struct at91_mmc_data __initdata cap9adk_mmc_data = {
  * MACB Ethernet device
  */
 static struct at91_eth_data __initdata cap9adk_macb_data = {
+	.phy_irq_pin	= -1,
 	.is_rmii	= 1,
 };
 

@@ -178,8 +180,8 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata cap9adk_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
-//	.rdy_pin	= ... not connected
+	.det_pin	= -1,
+	.rdy_pin	= -1,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,
 };

@@ -356,7 +358,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
  * AC97
  */
 static struct ac97c_platform_data cap9adk_ac97_data = {
-//	.reset_pin	= ... not connected
+	.reset_pin	= -1,
 };
 
 

@@ -64,6 +64,7 @@ static struct at91_eth_data __initdata carmeva_eth_data = {
 
 static struct at91_usbh_data __initdata carmeva_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata carmeva_udc_data = {

@@ -75,8 +76,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
 // static struct at91_cf_data __initdata carmeva_cf_data = {
 //	.det_pin	= AT91_PIN_PB0,
 //	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
+	// .irq_pin	= -1,
+	// .vcc_pin	= -1,
 // };
 
 static struct at91_mmc_data __initdata carmeva_mmc_data = {

@@ -84,6 +85,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PB10,
 	.wp_pin		= AT91_PIN_PC14,
+	.vcc_pin	= -1,
 };
 
 static struct spi_board_info carmeva_spi_devices[] = {

@@ -86,6 +86,7 @@ static void __init cpu9krea_init_early(void)
  */
 static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -93,13 +94,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
  */
 static struct at91_udc_data __initdata cpu9krea_udc_data = {
 	.vbus_pin	= AT91_PIN_PC8,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 /*
  * MACB Ethernet device
  */
 static struct at91_eth_data __initdata cpu9krea_macb_data = {
+	.phy_irq_pin	= -1,
 	.is_rmii	= 1,
 };
 

@@ -112,6 +114,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -1,
 };
 
 #ifdef CONFIG_MACH_CPU9260

@@ -337,6 +340,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA29,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 static void __init cpu9krea_board_init(void)

@@ -83,11 +83,13 @@ static void __init cpuat91_init_early(void)
 }
 
 static struct at91_eth_data __initdata cpuat91_eth_data = {
+	.phy_irq_pin	= -1,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata cpuat91_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata cpuat91_udc_data = {

@@ -98,6 +100,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
 static struct at91_mmc_data __initdata cpuat91_mmc_data = {
 	.det_pin	= AT91_PIN_PC2,
 	.wire4		= 1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 static struct physmap_flash_data cpuat91_flash_data = {

@@ -65,11 +65,12 @@ static struct at91_eth_data __initdata csb337_eth_data = {
 
 static struct at91_usbh_data __initdata csb337_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata csb337_udc_data = {
-	// this has no VBUS sensing pin
 	.pullup_pin	= AT91_PIN_PA24,
+	.vbus_pin	= -1,
 };
 
 static struct i2c_board_info __initdata csb337_i2c_devices[] = {

@@ -98,6 +99,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PD6,
+	.vcc_pin	= -1,
 };
 
 static struct spi_board_info csb337_spi_devices[] = {

@@ -59,6 +59,7 @@ static struct at91_eth_data __initdata csb637_eth_data = {
 
 static struct at91_usbh_data __initdata csb637_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata csb637_udc_data = {

@@ -67,6 +67,7 @@ static struct at91_eth_data __initdata eb9200_eth_data = {
 
 static struct at91_usbh_data __initdata eb9200_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata eb9200_udc_data = {

@@ -75,15 +76,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = {
 };
 
 static struct at91_cf_data __initdata eb9200_cf_data = {
+	.irq_pin	= -1,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -1,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 static struct at91_mmc_data __initdata eb9200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 static struct i2c_board_info __initdata eb9200_i2c_devices[] = {

@@ -71,11 +71,15 @@ static struct at91_eth_data __initdata ecb_at91eth_data = {
 
 static struct at91_usbh_data __initdata ecb_at91usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_mmc_data __initdata ecb_at91mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 

@@ -54,6 +54,7 @@ static struct at91_eth_data __initdata eco920_eth_data = {
 
 static struct at91_usbh_data __initdata eco920_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata eco920_udc_data = {

@@ -64,6 +65,9 @@ static struct at91_udc_data __initdata eco920_udc_data = {
 static struct at91_mmc_data __initdata eco920_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 0,
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 static struct physmap_flash_data eco920_flash_data = {

@@ -52,12 +52,13 @@ static void __init flexibity_init_early(void)
 /* USB Host port */
 static struct at91_usbh_data __initdata flexibity_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /* USB Device port */
 static struct at91_udc_data __initdata flexibity_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 /* SPI devices */

@@ -76,6 +77,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
 	.wp_pin		= AT91_PIN_PC4,
+	.vcc_pin	= -1,
 };
 
 /* LEDs */

@@ -106,6 +106,7 @@ static void __init foxg20_init_early(void)
  */
 static struct at91_usbh_data __initdata foxg20_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -113,7 +114,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = {
  */
 static struct at91_udc_data __initdata foxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -147,6 +148,9 @@ static struct at91_eth_data __initdata foxg20_macb_data = {
 static struct at91_mmc_data __initdata foxg20_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 

@@ -80,6 +80,7 @@ static void __init gsia18s_init_early(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -87,7 +88,7 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 /*

@@ -530,6 +531,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
 static struct at91_cf_data __initdata gsia18s_cf1_data = {
 	.irq_pin	= AT91_PIN_PA27,
 	.det_pin	= AT91_PIN_PB30,
+	.vcc_pin	= -1,
 	.rst_pin	= AT91_PIN_PB31,
 	.chipselect	= 5,
 	.flags		= AT91_CF_TRUE_IDE,

@@ -68,6 +68,7 @@ static struct at91_eth_data __initdata kafa_eth_data = {
 
 static struct at91_usbh_data __initdata kafa_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata kafa_udc_data = {

@@ -76,6 +76,7 @@ static struct at91_eth_data __initdata kb9202_eth_data = {
 
 static struct at91_usbh_data __initdata kb9202_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata kb9202_udc_data = {

@@ -87,6 +88,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = {
 	.det_pin	= AT91_PIN_PB2,
 	.slot_b		= 0,
 	.wire4		= 1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 static struct mtd_partition __initdata kb9202_nand_partition[] = {

@@ -106,7 +109,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata kb9202_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-	// .det_pin	= ... not there
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PC29,
 	.enable_pin	= AT91_PIN_PC28,
 	.partition_info	= nand_partitions,

@@ -79,7 +79,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = {
  */
 static struct at91_udc_data __initdata neocore926_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -149,6 +149,7 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
+	.vcc_pin	= -1,
 };
 
 

@@ -195,6 +196,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = {
 	.rdy_pin_active_low	= 1,
 	.enable_pin		= AT91_PIN_PD15,
 	.partition_info		= nand_partitions,
+	.det_pin		= -1,
 };
 
 static struct sam9_smc_config __initdata neocore926_nand_smc_config = {

@@ -107,6 +107,7 @@ static void __init add_device_pcontrol(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 

@@ -67,6 +67,7 @@ static struct at91_eth_data __initdata picotux200_eth_data = {
 
 static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_mmc_data __initdata picotux200_mmc_data = {

@@ -74,6 +75,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -1,
 };
 
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0

@@ -77,6 +77,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -84,7 +85,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 /*

@@ -139,7 +140,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -177,9 +178,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 /*

@@ -72,6 +72,7 @@ static struct at91_eth_data __initdata dk_eth_data = {
 
 static struct at91_usbh_data __initdata dk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata dk_udc_data = {

@@ -80,16 +81,19 @@ static struct at91_udc_data __initdata dk_udc_data = {
 };
 
 static struct at91_cf_data __initdata dk_cf_data = {
+	.irq_pin	= -1,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -1,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
 static struct at91_mmc_data __initdata dk_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 #endif
 

@@ -149,7 +153,7 @@ static struct atmel_nand_data __initdata dk_nand_data = {
 	.cle		= 21,
 	.det_pin	= AT91_PIN_PB1,
 	.rdy_pin	= AT91_PIN_PC2,
-	// .enable_pin	= ... not there
+	.enable_pin	= -1,
 	.partition_info	= nand_partitions,
 };
 

@@ -72,6 +72,7 @@ static struct at91_eth_data __initdata ek_eth_data = {
 
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata ek_udc_data = {

@@ -85,6 +86,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -1,
 };
 #endif
 

@@ -72,6 +72,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -140,7 +141,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -181,7 +182,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC8,
 	.wp_pin		= AT91_PIN_PC4,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -1,
 };
 
 static void __init ek_board_init(void)

@@ -75,6 +75,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -82,7 +83,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -182,7 +183,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -228,9 +229,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 

@@ -151,6 +151,7 @@ static void __init ek_add_device_dm9000(void) {}
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 

@@ -159,7 +160,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB29,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -188,7 +189,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-//	.det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PC15,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,

@@ -350,6 +351,9 @@ static struct spi_board_info ek_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 #endif /* CONFIG_SPI_ATMEL_* */

@@ -81,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -151,7 +151,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -1,
 };
 
 

@@ -189,7 +189,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,

@@ -358,6 +358,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -1,
 };
 
 

@@ -86,6 +86,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -93,7 +94,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -170,6 +171,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
+	.det_pin	= -1,
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {

@@ -215,6 +217,7 @@ static struct mci_platform_data __initdata ek_mmc_data = {
 	.slot[1] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PC9,
+		.wp_pin		= -1;
 	},
 
 };

@@ -223,6 +226,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,	/* Only one slot so use slot B */
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 #endif
 

@@ -232,6 +237,7 @@ static void __init ek_add_device_mmc(void)
 	if (ek_have_2mmc()) {
 		ek_mmc_data.slot[0].bus_width = 4;
 		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+		ek_mmc_data.slot[0].wp_pin = -1;
 	}
 	at91_add_device_mci(0, &ek_mmc_data);
 #else

@@ -100,6 +100,7 @@ static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PD10,
+		.wp_pin		= -1;
 	},
 };
 

@@ -150,6 +151,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
+	.det_pin	= -1,
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {

@@ -335,6 +337,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -1,
 };
 
 

@@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA15,
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 

@@ -97,7 +97,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
 	.partition_info	= nand_partitions,

@@ -209,6 +209,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -1,
 };
 
 

@@ -57,15 +57,18 @@ static void __init snapper9260_init_early(void)
 
 static struct at91_usbh_data __initdata snapper9260_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 static struct at91_udc_data __initdata snapper9260_udc_data = {
 	.vbus_pin		= SNAPPER9260_IO_EXP_GPIO(5),
 	.vbus_active_low	= 1,
 	.vbus_polled		= 1,
+	.pullup_pin		= -1,
 };
 
 static struct at91_eth_data snapper9260_macb_data = {
+	.phy_irq_pin	= -1,
 	.is_rmii	= 1,
 };
 

@@ -110,6 +113,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.partition_info	= snapper9260_nand_partition_info,
 	.bus_width_16	= 0,
+	.enable_pin	= -1,
+	.det_pin	= -1,
 };
 
 static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {

@@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -1,
 };
 
 static struct sam9_smc_config __initdata nand_smc_config = {

@@ -122,12 +123,17 @@ static void __init add_device_nand(void)
 static struct mci_platform_data __initdata mmc_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+		.detect_pin	= -1;
+		.wp_pin		= -1;
 	},
 };
 #else
 static struct at91_mmc_data __initdata mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 #endif
 

@@ -137,6 +143,7 @@ static struct at91_mmc_data __initdata mmc_data = {
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 

@@ -145,12 +152,12 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata portuxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC7,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 

@@ -66,6 +66,7 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-1, -1},
 };
 
 /*

@@ -73,7 +74,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB11,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -1,		/* pull-up driven by UDC */
 };
 
 static void __init ek_add_device_udc(void)

@@ -199,7 +200,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,

@@ -120,6 +120,7 @@ static struct at91_eth_data __initdata yl9200_eth_data = {
  */
 static struct at91_usbh_data __initdata yl9200_usbh_data = {
 	.ports			= 1,	/* PQFP version of AT91RM9200 */
+	.vbus_pin		= {-1, -1},
 };
 
 /*

@@ -137,8 +138,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
  */
 static struct at91_mmc_data __initdata yl9200_mmc_data = {
 	.det_pin	= AT91_PIN_PB9,
-	// .wp_pin	= ... not connected
 	.wire4		= 1,
+	.wp_pin		= -1,
+	.vcc_pin	= -1,
 };
 
 /*

@@ -181,7 +183,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
 static struct atmel_nand_data __initdata yl9200_nand_data = {
 	.ale		= 6,
 	.cle		= 7,
-	// .det_pin	= ... not connected
+	.det_pin	= -1,
 	.rdy_pin	= AT91_PIN_PC14,	/* R/!B (Sheet10) */
 	.enable_pin	= AT91_PIN_PC15,	/* !CE  (Sheet10) */
 	.partition_info	= nand_partitions,