Hello.

Kukjin Kim wrote:

From: Abhilash Kesavan <redacted>

Adds support for the Samsung PATA controller. This driver is based on the
Libata subsystem and references the earlier patches sent for IDE subsystem.

Signed-off-by: Abhilash Kesavan <redacted>
Signed-off-by: Kukjin Kim <redacted>
Cc: Ben Dooks <ben-linux@fluff.org>

    There's probably still a place for improvement... sorry that I dind't 
notice before. Other than that:

Acked-by: Sergei Shtylyov <redacted>

[...]

[...]

+/*
+ * pata_s3c_wait_after_reset - wait for devices to become ready after reset
+ */
+static int pata_s3c_wait_after_reset(struct ata_link *link,
+		unsigned int devmask, unsigned long deadline)
+{
+	struct ata_port *ap = link->ap;
+	struct ata_ioports *ioaddr = &ap->ioaddr;
+	unsigned int dev0 = devmask & (1 << 0);
+	unsigned int dev1 = devmask & (1 << 1);
+	int rc, ret = 0;
+
+	msleep(ATA_WAIT_AFTER_RESET);
+
+	/* always check readiness of the master device */
+	rc = ata_sff_wait_ready(link, deadline);
+	/* -ENODEV means the odd clown forgot the D7 pulldown resistor
+	 * and TF status is 0xff, bail out on it too.
+	 */
+	if (rc)
+		return rc;
+
+	/* if device 1 was found in ata_devchk, wait for register
+	 * access briefly, then wait for BSY to clear.
+	 */

    You don't call pata_s3c_devchk() for device 1, so in principle you can 
drop the following block:

+	if (dev1) {
+		int i;
+
+		pata_s3c_dev_select(ap, 1);
+
+		/* Wait for register access.  Some ATAPI devices fail
+		 * to set nsect/lbal after reset, so don't waste too
+		 * much time on it.  We're gonna wait for !BSY anyway.
+		 */
+		for (i = 0; i < 2; i++) {
+			u8 nsect, lbal;
+
+			nsect = ata_inb(ap->host, ioaddr->nsect_addr);
+			lbal = ata_inb(ap->host, ioaddr->lbal_addr);
+			if ((nsect == 1) && (lbal == 1))
+				break;
+			msleep(50);	/* give drive a breather */
+		}
+
+		rc = ata_sff_wait_ready(link, deadline);
+		if (rc) {
+			if (rc != -ENODEV)
+				return rc;
+			ret = rc;
+		}
+	}
+
+	/* is all this really necessary? */
+	pata_s3c_dev_select(ap, 0);
+	if (dev1)
+		pata_s3c_dev_select(ap, 1);

    This too...

+	if (dev0)
+		pata_s3c_dev_select(ap, 0);
+
+	return ret;
+}
+

[...]

+static int pata_s3c_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct ata_host *host = platform_get_drvdata(pdev);
+	struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
+	struct s3c_ide_info *info;
+
+	info = host->private_data;

    Could be initializer...

MBR, Sergei