Re: [PATCH RFC 00/20] attestation: Add a common subsystem and TDX support

From
Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Date
2026-10-23 08:05:04
Also in
kvm, linux-coco, linux-doc, lkml
Reply to
Jiri Pirko, 2026-10-22
Jiri Pirko [off-list ref] writes:
Thu, Oct 22, 2026 at 12:30:47PM +0200, aneesh.kumar@kernel.org wrote:
quoted
Jiri Pirko [off-list ref] writes:
quoted
From: Jiri Pirko <redacted>
 [ ... 67 lines skipped ... ] 
quoted
quoted
I am using this to understand what the IDE setup flow would look like,
but it is unclear whether the connect flow belongs in an attestation
framework. I understand the desire to pass the certificate slot number
as part of connect, and sysfs is probably not a suitable interface for
that. However, is CTLV the interface we want to use for connect?
I was thinking about this and "connect" really does not belong in the
attestation CTLV (same applies to "lock"). I was thinking about some
parallel PCITSM CTLV instance, but that does not really click as well.

Currently I'm thinking we can maintain existing "connect" in sysfs and
extend it with "lock" sysfs knob for Realm side. Both would create
ctlv-attestation-spdm instance. The same spdm instance may be created
for other non-PCI-backed device.

The proposed host flow is:

    sysfs connect: select tsmN and prepare the connection
        -> negotiate SPDM and discover certificates
        -> register ctlv-attestation-spdm instance in DISCOVERED state

    SPDM_GET
        -> populated certificate slots and digests

    EVIDENCE_GET(CERT_CHAIN, blob-instance=slot) /*optional*/
        -> retrieve candidate certificate chain for appraisal

    SPDM_AUTHENTICATE(device-generation, spdm-slot=selected_slot)
        -> authenticate the selected chain
        -> complete backend-required session and IDE setup

    sysfs disconnect
        -> remove the attestation instance
        -> destroy the native connection

The slot is therefore selected after discovery, rather than supplied to
connect. The attestation instance represents the prepared connection; it
does not exist beforehand as a controller for a disconnected PCI function.
CCA currently takes the device identity index during pdev_create. I am
investigating how to retrieve the certificate chains for all slots. For
now, I have implemented the sequence below.

echo tsm0 > /sys/bus/pci/devices/$DEVICE/tsm/connect

./ctlvctl/ctlvctl --spec-dir=./specs/ exec ctlv0 device-get                                                               
# device-get, 1 fragment, generation 0                                                                                      
  device.generation 0            
  device.caps                                                                                                               
    cap.evidence                                                                                                            
      cap.min-challenge-length 0                                                                                            
      cap.max-challenge-length 0                                                                                            
      cap.max-total-output-length 369098752                                                                                 
      cap.evidence-flags evidence-accept
      cap.object                                                                                                            
        cap.blob-class cert-chain                                                                                           
        cap.blob-instance 0                                                                                                 
        cap.format spdm-cert-chain
        cap.representation raw                                                                                              
        cap.representation tcb-digest                                                                                       
        cap.hash-algo 4                                                                                                     
        cap.hash-algo 5          
        cap.hash-algo 6                                                                                                     
        cap.max-length 16777216                                                                                             
  device.info                                                                                                               
    pci.name 0000:02:00.0                       

I think we can use evidence-refresh to select the blob-instance for the
desired slot once the CCA specification supports that.

 ./ctlvctl/ctlvctl --spec-dir=./specs/ exec ctlv0 state-get                                                                
# state-get, 1 fragment, generation 0
  pci.generation 0                                                                                                          
  pci.connected 1                                                                                                           
  pci.locked 0                                                                                                              
  pci.accepted 0                 
  pci.tsm-id 0                                                                                                              
  pci.dsm 0000:02:00.0                                                                                                      

device is marked connected, but IDE is not setup as indicated by pci.accepted = 0


./ctlvctl/ctlvctl --spec-dir=./specs/ exec ctlv0 evidence-get --json '{
"evidence.challenge": "hex:", "evidence.object": [{
"evidence.blob-class": "cert-chain", "evidence.format":
"spdm-cert-chain", "evidence.blob-instance": 0,
"evidence.representation": "raw", "evidence.data": { "file":
"/tmp/cert0.bin", "data-buf-size": 16777216 } }] }'
# evidence-get, 1 fragment, generation 0                                                                                    
  device.generation 0                                                                                                       
  evidence.generation 1                                                                                                     
  evidence.object-length 1632           


I added the file: attribute to verify the evidence blob's contents. ie,
we can do:

# file cert0.bin  
cert0.bin: Certificate, Version=3

./ctlvctl/ctlvctl --spec-dir=./specs/ exec ctlv0 evidence-accept device.generation=0 evidence.generation=1
# acknowledged
./ctlvctl/ctlvctl --spec-dir=./specs/ exec ctlv0 state-get
# state-get, 1 fragment, generation 0
  pci.generation 0
  pci.connected 1
  pci.locked 0
  pci.accepted 1
  pci.tsm-id 0
  pci.dsm 0000:02:00.0


I am wondering why we need 'devsec-run' ops. Isn't that already the result of
'evidence-accept'?

-aneesh
Thread (212 messages) 212 messages, 15 authors, last reply 6d ago
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help