Support for Cortex-M Prototyping System

@@ -0,0 +1,28 @@
+ARM MPS2 timer
+
+The MPS2 platform has simple general-purpose 32 bits timers.
+
+Required properties:
+- compatible	: Should be "arm,mps2-timer"
+- reg		: Address and length of the register set
+- interrupts	: Reference to the timer interrupt
+
+Required clocking property, have to be one of:
+- clocks	  : The input clock of the timer
+- clock-frequency : The rate in HZ in input of the ARM MPS2 timer
+
+Examples:
+
+timer1: mps2-timer@40000000 {
+	compatible = "arm,mps2-timer";
+	reg = <0x40000000 0x1000>;
+	interrupts = <8>;
+	clocks = <&sysclk>;
+};
+
+timer2: mps2-timer@40001000 {
+	compatible = "arm,mps2-timer";
+	reg = <0x40001000 0x1000>;
+	interrupts = <9>;
+	clock-frequency = <25000000>;
+};

@@ -185,6 +185,12 @@ config CLKSRC_STM32
 	depends on OF && ARM && (ARCH_STM32 || COMPILE_TEST)
 	select CLKSRC_MMIO
 
+config CLKSRC_MPS2
+	bool "Clocksource for MPS2 SoCs" if COMPILE_TEST
+	depends on GENERIC_SCHED_CLOCK
+	select CLKSRC_MMIO
+	select CLKSRC_OF
+
 config ARM_ARCH_TIMER
 	bool
 	select CLKSRC_OF if OF

@@ -39,6 +39,7 @@ obj-$(CONFIG_CLKSRC_EFM32)	+= time-efm32.o
 obj-$(CONFIG_CLKSRC_STM32)	+= timer-stm32.o
 obj-$(CONFIG_CLKSRC_EXYNOS_MCT)	+= exynos_mct.o
 obj-$(CONFIG_CLKSRC_LPC32XX)	+= time-lpc32xx.o
+obj-$(CONFIG_CLKSRC_MPS2)	+= mps2-timer.o
 obj-$(CONFIG_CLKSRC_SAMSUNG_PWM)	+= samsung_pwm_timer.o
 obj-$(CONFIG_FSL_FTM_TIMER)	+= fsl_ftm_timer.o
 obj-$(CONFIG_VF_PIT_TIMER)	+= vf_pit_timer.o

@@ -0,0 +1,275 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt
+
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/of_address.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/sched_clock.h>
+#include <linux/slab.h>
+
+#define TIMER_CTRL		0x0
+#define TIMER_CTRL_ENABLE	BIT(0)
+#define TIMER_CTRL_IE		BIT(3)
+
+#define TIMER_VALUE		0x4
+#define TIMER_RELOAD		0x8
+#define TIMER_INT		0xc
+
+struct clockevent_mps2 {
+	void __iomem *reg;
+	u32 clock_count_per_tick;
+	struct clock_event_device clkevt;
+};
+
+static void __iomem *sched_clock_base;
+
+static u64 notrace mps2_sched_read(void)
+{
+	return ~readl_relaxed(sched_clock_base + TIMER_VALUE);
+}
+
+static inline struct clockevent_mps2 *to_mps2_clkevt(struct clock_event_device *c)
+{
+	return container_of(c, struct clockevent_mps2, clkevt);
+}
+
+static void clockevent_mps2_writel(u32 val, struct clock_event_device *c, u32 offset)
+{
+	writel_relaxed(val, to_mps2_clkevt(c)->reg + offset);
+}
+
+static int mps2_timer_shutdown(struct clock_event_device *ce)
+{
+	clockevent_mps2_writel(0, ce, TIMER_RELOAD);
+	clockevent_mps2_writel(0, ce, TIMER_CTRL);
+
+	return 0;
+}
+
+static int mps2_timer_set_next_event(unsigned long next, struct clock_event_device *ce)
+{
+	clockevent_mps2_writel(next, ce, TIMER_VALUE);
+	clockevent_mps2_writel(TIMER_CTRL_IE | TIMER_CTRL_ENABLE, ce, TIMER_CTRL);
+
+	return 0;
+}
+
+static int mps2_timer_set_periodic(struct clock_event_device *ce)
+{
+	u32 clock_count_per_tick = to_mps2_clkevt(ce)->clock_count_per_tick;
+
+	clockevent_mps2_writel(clock_count_per_tick, ce, TIMER_RELOAD);
+	clockevent_mps2_writel(clock_count_per_tick, ce, TIMER_VALUE);
+	clockevent_mps2_writel(TIMER_CTRL_IE | TIMER_CTRL_ENABLE, ce, TIMER_CTRL);
+
+	return 0;
+}
+
+static irqreturn_t mps2_timer_interrupt(int irq, void *dev_id)
+{
+	struct clockevent_mps2 *ce = dev_id;
+	u32 status = readl_relaxed(ce->reg + TIMER_INT);
+
+	if (!status) {
+		pr_warn("spurious interrupt\n");
+		return IRQ_NONE;
+	}
+
+	writel_relaxed(1, ce->reg + TIMER_INT);
+
+	ce->clkevt.event_handler(&ce->clkevt);
+
+	return IRQ_HANDLED;
+}
+
+static int __init mps2_clockevent_init(struct device_node *np)
+{
+	void __iomem *base;
+	struct clk *clk = NULL;
+	struct clockevent_mps2 *ce;
+	u32 rate;
+	int irq, ret;
+	const char *name = "mps2-clkevt";
+
+	ret = of_property_read_u32(np, "clock-frequency", &rate);
+	if (ret) {
+		clk = of_clk_get(np, 0);
+		if (IS_ERR(clk)) {
+			ret = PTR_ERR(clk);
+			pr_err("failed to get clock for clockevent: %d\n", ret);
+			goto out;
+		}
+
+		ret = clk_prepare_enable(clk);
+		if (ret) {
+			pr_err("failed to enable clock for clockevent: %d\n", ret);
+			goto out_clk_put;
+		}
+
+		rate = clk_get_rate(clk);
+	}
+
+	base = of_iomap(np, 0);
+	if (!base) {
+		ret = -EADDRNOTAVAIL;
+		pr_err("failed to map register for clockevent: %d\n", ret);
+		goto out_clk_disable;
+	}
+
+	irq = irq_of_parse_and_map(np, 0);
+	if (!irq) {
+		ret = -ENOENT;
+		pr_err("failed to get irq for clockevent: %d\n", ret);
+		goto out_iounmap;
+	}
+
+	ce = kzalloc(sizeof(struct clockevent_mps2), GFP_KERNEL);
+	if (!ce) {
+		ret = -ENOMEM;
+		goto out_iounmap;
+	}
+
+	ce->reg = base;
+	ce->clock_count_per_tick = DIV_ROUND_CLOSEST(rate, HZ);
+	ce->clkevt.irq = irq;
+	ce->clkevt.name = name;
+	ce->clkevt.rating = 200;
+	ce->clkevt.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
+	ce->clkevt.cpumask = cpu_possible_mask;
+	ce->clkevt.set_state_shutdown	= mps2_timer_shutdown,
+	ce->clkevt.set_state_periodic	= mps2_timer_set_periodic,
+	ce->clkevt.set_state_oneshot	= mps2_timer_shutdown,
+	ce->clkevt.set_next_event	= mps2_timer_set_next_event;
+
+	/* Ensure timer is disabled */
+	writel_relaxed(0, base + TIMER_CTRL);
+
+	ret = request_irq(irq, mps2_timer_interrupt, IRQF_TIMER, name, ce);
+	if (ret) {
+		pr_err("failed to request irq for clockevent: %d\n", ret);
+		goto out_kfree;
+	}
+
+	clockevents_config_and_register(&ce->clkevt, rate, 0xf, 0xffffffff);
+
+	return 0;
+
+out_kfree:
+	kfree(ce);
+out_iounmap:
+	iounmap(base);
+out_clk_disable:
+	/* clk_{disable, unprepare, put}() can handle NULL as a parameter */
+	clk_disable_unprepare(clk);
+out_clk_put:
+	clk_put(clk);
+out:
+	return ret;
+}
+
+static int __init mps2_clocksource_init(struct device_node *np)
+{
+	void __iomem *base;
+	struct clk *clk = NULL;
+	u32 rate;
+	int ret;
+	const char *name = "mps2-clksrc";
+
+	ret = of_property_read_u32(np, "clock-frequency", &rate);
+	if (ret) {
+		clk = of_clk_get(np, 0);
+		if (IS_ERR(clk)) {
+			ret = PTR_ERR(clk);
+			pr_err("failed to get clock for clocksource: %d\n", ret);
+			goto out;
+		}
+
+		ret = clk_prepare_enable(clk);
+		if (ret) {
+			pr_err("failed to enable clock for clocksource: %d\n", ret);
+			goto out_clk_put;
+		}
+
+		rate = clk_get_rate(clk);
+	}
+
+	base = of_iomap(np, 0);
+	if (!base) {
+		ret = -EADDRNOTAVAIL;
+		pr_err("failed to map register for clocksource: %d\n", ret);
+		goto out_clk_disable;
+	}
+
+	/* Ensure timer is disabled */
+	writel_relaxed(0, base + TIMER_CTRL);
+
+	/* ... and set it up as free-running clocksource */
+	writel_relaxed(0xffffffff, base + TIMER_VALUE);
+	writel_relaxed(0xffffffff, base + TIMER_RELOAD);
+
+	writel_relaxed(TIMER_CTRL_ENABLE, base + TIMER_CTRL);
+
+	ret = clocksource_mmio_init(base + TIMER_VALUE, name,
+				    rate, 200, 32,
+				    clocksource_mmio_readl_down);
+	if (ret) {
+		pr_err("failed to init clocksource: %d\n", ret);
+		goto out_iounmap;
+	}
+
+	sched_clock_base = base;
+	sched_clock_register(mps2_sched_read, 32, rate);
+
+	return 0;
+
+out_iounmap:
+	iounmap(base);
+out_clk_disable:
+	/* clk_{disable, unprepare, put}() can handle NULL as a parameter */
+	clk_disable_unprepare(clk);
+out_clk_put:
+	clk_put(clk);
+out:
+	return ret;
+}
+
+static void __init mps2_timer_init(struct device_node *np)
+{
+	static int has_clocksource, has_clockevent;
+	int ret;
+
+	if (!has_clocksource) {
+		ret = mps2_clocksource_init(np);
+		if (!ret) {
+			has_clocksource = 1;
+			return;
+		}
+	}
+
+	if (!has_clockevent) {
+		ret = mps2_clockevent_init(np);
+		if (!ret) {
+			has_clockevent = 1;
+			return;
+		}
+	}
+}
+
+CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);

@@ -1450,6 +1450,18 @@ config SERIAL_EFM32_UART
 	  This driver support the USART and UART ports on
 	  Energy Micro's efm32 SoCs.
 
+config SERIAL_MPS2_UART_CONSOLE
+	bool "MPS2 UART console support"
+	depends on SERIAL_MPS2_UART
+	select SERIAL_CORE_CONSOLE
+
+config SERIAL_MPS2_UART
+	bool "MPS2 UART port"
+	depends on ARM || COMPILE_TEST
+	select SERIAL_CORE
+	help
+	  This driver support the UART ports on ARM MPS2.
+
 config SERIAL_EFM32_UART_CONSOLE
 	bool "EFM32 UART/USART console support"
 	depends on SERIAL_EFM32_UART=y

@@ -91,6 +91,7 @@ obj-$(CONFIG_SERIAL_CONEXANT_DIGICOLOR)	+= digicolor-usart.o
 obj-$(CONFIG_SERIAL_MEN_Z135)	+= men_z135_uart.o
 obj-$(CONFIG_SERIAL_SPRD) += sprd_serial.o
 obj-$(CONFIG_SERIAL_STM32)	+= stm32-usart.o
+obj-$(CONFIG_SERIAL_MPS2_UART)	+= mps2-uart.o
 
 # GPIOLIB helpers for modem control lines
 obj-$(CONFIG_SERIAL_MCTRL_GPIO)	+= serial_mctrl_gpio.o

@@ -0,0 +1,586 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * TODO: support for SysRq
+ */
+
+#define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/tty_flip.h>
+#include <linux/types.h>
+
+#define SERIAL_NAME	"ttyMPS"
+#define DRIVER_NAME	"mps2-uart"
+#define MAKE_NAME(x)	(DRIVER_NAME # x)
+
+#define UARTn_DATA				0x00
+
+#define UARTn_STATE				0x04
+#define UARTn_STATE_TX_FULL			BIT(0)
+#define UARTn_STATE_RX_FULL			BIT(1)
+#define UARTn_STATE_TX_OVERRUN			BIT(2)
+#define UARTn_STATE_RX_OVERRUN			BIT(3)
+
+#define UARTn_CTRL				0x08
+#define UARTn_CTRL_TX_ENABLE			BIT(0)
+#define UARTn_CTRL_RX_ENABLE			BIT(1)
+#define UARTn_CTRL_TX_INT_ENABLE		BIT(2)
+#define UARTn_CTRL_RX_INT_ENABLE		BIT(3)
+#define UARTn_CTRL_TX_OVERRUN_INT_ENABLE	BIT(4)
+#define UARTn_CTRL_RX_OVERRUN_INT_ENABLE	BIT(5)
+
+#define UARTn_INT				0x0c
+#define UARTn_INT_TX				BIT(0)
+#define UARTn_INT_RX				BIT(1)
+#define UARTn_INT_TX_OVERRUN			BIT(2)
+#define UARTn_INT_RX_OVERRUN			BIT(3)
+
+#define UARTn_BAUDDIV				0x10
+#define UARTn_BAUDDIV_MASK			GENMASK(20, 0)
+
+/*
+ * Helpers to make typical enable/disable operations more readable.
+ */
+#define UARTn_CTRL_TX_GRP 			(UARTn_CTRL_TX_ENABLE		 |\
+						 UARTn_CTRL_TX_INT_ENABLE	 |\
+						 UARTn_CTRL_TX_OVERRUN_INT_ENABLE)
+
+#define UARTn_CTRL_RX_GRP 			(UARTn_CTRL_RX_ENABLE		 |\
+						 UARTn_CTRL_RX_INT_ENABLE	 |\
+						 UARTn_CTRL_RX_OVERRUN_INT_ENABLE)
+
+#define MPS2_MAX_PORTS				3
+
+struct mps2_uart_port {
+	struct uart_port port;
+	struct clk *clk;
+	unsigned int tx_irq;
+	unsigned int rx_irq;
+};
+
+static inline struct mps2_uart_port *to_mps2_port(struct uart_port *port)
+{
+	return container_of(port, struct mps2_uart_port, port);
+}
+
+static void mps2_uart_write8(struct uart_port *port, u8 val, unsigned off)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+	writeb(val, mps_port->port.membase + off);
+}
+
+static u8 mps2_uart_read8(struct uart_port *port, unsigned off)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+	return readb(mps_port->port.membase + off);
+}
+
+static void mps2_uart_write32(struct uart_port *port, u32 val, unsigned off)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+	writel_relaxed(val, mps_port->port.membase + off);
+}
+
+static unsigned int mps2_uart_tx_empty(struct uart_port *port)
+{
+	u8 status = mps2_uart_read8(port, UARTn_STATE);
+
+	return (status & UARTn_STATE_TX_FULL) ? 0 : TIOCSER_TEMT;
+}
+
+static void mps2_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static unsigned int mps2_uart_get_mctrl(struct uart_port *port)
+{
+	return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR;
+}
+
+static void mps2_uart_stop_tx(struct uart_port *port)
+{
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control &= ~UARTn_CTRL_TX_GRP;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+}
+
+static void mps2_uart_tx_chars(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+
+	while (!(mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)) {
+		if (port->x_char) {
+			mps2_uart_write8(port, port->x_char, UARTn_DATA);
+			port->x_char = 0;
+			port->icount.tx++;
+			continue;
+		}
+
+		if (uart_circ_empty(xmit) || uart_tx_stopped(port))
+			break;
+
+		mps2_uart_write8(port, xmit->buf[xmit->tail], UARTn_DATA);
+		xmit->tail = (xmit->tail + 1) % UART_XMIT_SIZE;
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		mps2_uart_stop_tx(port);
+}
+
+static void mps2_uart_start_tx(struct uart_port *port)
+{
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control |= UARTn_CTRL_TX_GRP;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+	mps2_uart_tx_chars(port);
+}
+
+static void mps2_uart_stop_rx(struct uart_port *port)
+{
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control &= ~UARTn_CTRL_RX_GRP;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+}
+
+static void mps2_uart_break_ctl(struct uart_port *port, int ctl)
+{
+}
+
+static void mps2_uart_rx_chars(struct uart_port *port)
+{
+	struct tty_port *tport = &port->state->port;
+
+	while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_RX_FULL) {
+		u8 rxdata = mps2_uart_read8(port, UARTn_DATA);
+
+		port->icount.rx++;
+		tty_insert_flip_char(&port->state->port, rxdata, TTY_NORMAL);
+	}
+
+	spin_unlock(&port->lock);
+	tty_flip_buffer_push(tport);
+	spin_lock(&port->lock);
+}
+
+static irqreturn_t mps2_uart_rxirq(int irq, void *data)
+{
+
+	struct uart_port *port = data;
+	u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+	if (unlikely(!(irqflag & UARTn_INT_RX)))
+		return IRQ_NONE;
+
+	spin_lock(&port->lock);
+
+	mps2_uart_write8(port, UARTn_INT_RX, UARTn_INT);
+	mps2_uart_rx_chars(port);
+
+	spin_unlock(&port->lock);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mps2_uart_txirq(int irq, void *data)
+{
+	struct uart_port *port = data;
+	u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+	if (unlikely(!(irqflag & UARTn_INT_TX)))
+		return IRQ_NONE;
+
+	mps2_uart_write8(port, UARTn_INT_TX, UARTn_INT);
+	mps2_uart_tx_chars(port);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mps2_uart_oerrirq(int irq, void *data)
+{
+	irqreturn_t handled = IRQ_NONE;
+	struct uart_port *port = data;
+	u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+	spin_lock(&port->lock);
+
+	if (irqflag & UARTn_INT_RX_OVERRUN) {
+		struct tty_port *tport = &port->state->port;
+
+		mps2_uart_write8(port, UARTn_INT_RX_OVERRUN, UARTn_INT);
+		tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+		port->icount.overrun++;
+		handled = IRQ_HANDLED;
+	}
+
+	/*
+	 * It's never been seen in practice and it never *should* happen since
+	 * we check if there is enough room in TX buffer before sending data.
+	 * So we keep this check in case something suspicious has happened.
+	 */
+	if (irqflag & UARTn_INT_TX_OVERRUN) {
+		mps2_uart_write8(port, UARTn_INT_TX_OVERRUN, UARTn_INT);
+		handled = IRQ_HANDLED;
+	}
+
+	spin_unlock(&port->lock);
+
+	return handled;
+}
+
+static int mps2_uart_startup(struct uart_port *port)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+	int ret;
+
+	control &= ~(UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP);
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+
+	ret = request_irq(mps_port->rx_irq, mps2_uart_rxirq, 0,
+			  MAKE_NAME(-rx), mps_port);
+	if (ret) {
+		dev_err(port->dev, "failed to register rxirq (%d)\n", ret);
+		return ret;
+	}
+
+	ret = request_irq(mps_port->tx_irq, mps2_uart_txirq, 0,
+			  MAKE_NAME(-tx), mps_port);
+	if (ret) {
+		dev_err(port->dev, "failed to register txirq (%d)\n", ret);
+		goto err_free_rxirq;
+	}
+
+	ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED,
+			  MAKE_NAME(-overrun), mps_port);
+
+	if (ret) {
+		dev_err(port->dev, "failed to register oerrirq (%d)\n", ret);
+		goto err_free_txirq;
+	}
+
+	control |= UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+
+	return 0;
+
+err_free_txirq:
+	free_irq(mps_port->tx_irq, mps_port);
+err_free_rxirq:
+	free_irq(mps_port->rx_irq, mps_port);
+
+	return ret;
+}
+
+static void mps2_uart_shutdown(struct uart_port *port)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control &= ~(UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP);
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+
+	free_irq(mps_port->rx_irq, mps_port);
+	free_irq(mps_port->tx_irq, mps_port);
+	free_irq(port->irq, mps_port);
+}
+
+static void mps2_uart_set_termios(struct uart_port *port,
+	struct ktermios *termios, struct ktermios *old)
+{
+	unsigned long flags;
+	unsigned int baud, bauddiv;
+
+	termios->c_cflag &= ~(CRTSCTS | CMSPAR);
+	termios->c_cflag &= ~CSIZE;
+	termios->c_cflag |= CS8;
+	termios->c_cflag &= ~PARENB;
+	termios->c_cflag &= ~CSTOPB;
+
+	baud = uart_get_baud_rate(port, termios, old,
+			DIV_ROUND_CLOSEST(port->uartclk, UARTn_BAUDDIV_MASK),
+			DIV_ROUND_CLOSEST(port->uartclk, 16));
+
+	bauddiv = DIV_ROUND_CLOSEST(port->uartclk, baud);
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	uart_update_timeout(port, termios->c_cflag, baud);
+	mps2_uart_write32(port, bauddiv, UARTn_BAUDDIV);
+
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *mps2_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_MPS2UART) ? DRIVER_NAME : NULL;
+}
+
+static void mps2_uart_release_port(struct uart_port *port)
+{
+}
+
+static int mps2_uart_request_port(struct uart_port *port)
+{
+	return 0;
+}
+
+static void mps2_uart_config_port(struct uart_port *port, int type)
+{
+	if (type & UART_CONFIG_TYPE && !mps2_uart_request_port(port))
+		port->type = PORT_MPS2UART;
+}
+
+static int mps2_uart_verify_port(struct uart_port *port, struct serial_struct *serinfo)
+{
+	return -EINVAL;
+}
+
+static const struct uart_ops mps2_uart_pops = {
+	.tx_empty = mps2_uart_tx_empty,
+	.set_mctrl = mps2_uart_set_mctrl,
+	.get_mctrl = mps2_uart_get_mctrl,
+	.stop_tx = mps2_uart_stop_tx,
+	.start_tx = mps2_uart_start_tx,
+	.stop_rx = mps2_uart_stop_rx,
+	.break_ctl = mps2_uart_break_ctl,
+	.startup = mps2_uart_startup,
+	.shutdown = mps2_uart_shutdown,
+	.set_termios = mps2_uart_set_termios,
+	.type = mps2_uart_type,
+	.release_port = mps2_uart_release_port,
+	.request_port = mps2_uart_request_port,
+	.config_port = mps2_uart_config_port,
+	.verify_port = mps2_uart_verify_port,
+};
+
+static struct mps2_uart_port mps2_uart_ports[MPS2_MAX_PORTS];
+
+#ifdef CONFIG_SERIAL_MPS2_UART_CONSOLE
+static void mps2_uart_console_putchar(struct uart_port *port, int ch)
+{
+	while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)
+		cpu_relax();
+
+	mps2_uart_write8(port, ch, UARTn_DATA);
+}
+
+static void mps2_uart_console_write(struct console *co, const char *s, unsigned int cnt)
+{
+	struct uart_port *port = &mps2_uart_ports[co->index].port;
+
+	uart_console_write(port, s, cnt, mps2_uart_console_putchar);
+}
+
+static int mps2_uart_console_setup(struct console *co, char *options)
+{
+	struct mps2_uart_port *mps_port;
+	int baud = 9600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index < 0 || co->index >= MPS2_MAX_PORTS)
+		return -ENODEV;
+
+	mps_port = &mps2_uart_ports[co->index];
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(&mps_port->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver mps2_uart_driver;
+
+static struct console mps2_uart_console = {
+	.name = SERIAL_NAME,
+	.device = uart_console_device,
+	.write = mps2_uart_console_write,
+	.setup = mps2_uart_console_setup,
+	.flags = CON_PRINTBUFFER,
+	.index = -1,
+	.data = &mps2_uart_driver,
+};
+
+#define MPS2_SERIAL_CONSOLE (&mps2_uart_console)
+
+#else
+#define MPS2_SERIAL_CONSOLE NULL
+#endif
+
+static struct uart_driver mps2_uart_driver = {
+	.driver_name = DRIVER_NAME,
+	.dev_name = SERIAL_NAME,
+	.nr = MPS2_MAX_PORTS,
+	.cons = MPS2_SERIAL_CONSOLE,
+};
+
+static struct mps2_uart_port *mps2_of_get_port(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	int id;
+
+	if (!np)
+		return NULL;
+
+	id = of_alias_get_id(np, "serial");
+	if (id < 0)
+		id = 0;
+
+	if (WARN_ON(id >= MPS2_MAX_PORTS))
+		return NULL;
+
+	mps2_uart_ports[id].port.line = id;
+	return &mps2_uart_ports[id];
+}
+
+static int mps2_init_port(struct mps2_uart_port *mps_port,
+			struct platform_device *pdev)
+{
+	struct resource *res;
+	int ret;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mps_port->port.membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mps_port->port.membase))
+		return PTR_ERR(mps_port->port.membase);
+
+	mps_port->port.mapbase = res->start;
+	mps_port->port.mapsize = resource_size(res);
+
+	mps_port->rx_irq = platform_get_irq(pdev, 0);
+	mps_port->tx_irq = platform_get_irq(pdev, 1);
+	mps_port->port.irq = platform_get_irq(pdev, 2);
+
+	mps_port->port.iotype = UPIO_MEM;
+	mps_port->port.flags = UPF_BOOT_AUTOCONF;
+	mps_port->port.fifosize = 1;
+	mps_port->port.ops = &mps2_uart_pops;
+	mps_port->port.dev = &pdev->dev;
+
+	mps_port->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(mps_port->clk))
+		return PTR_ERR(mps_port->clk);
+
+	ret = clk_prepare_enable(mps_port->clk);
+	if (ret)
+		return ret;
+
+	mps_port->port.uartclk = clk_get_rate(mps_port->clk);
+
+	clk_disable_unprepare(mps_port->clk);
+
+	return ret;
+}
+
+static int mps2_serial_probe(struct platform_device *pdev)
+{
+	struct mps2_uart_port *mps_port;
+	int ret;
+
+	mps_port = mps2_of_get_port(pdev);
+	if (!mps_port)
+		return -ENODEV;
+
+	ret = mps2_init_port(mps_port, pdev);
+	if (ret)
+		return ret;
+
+	ret = uart_add_one_port(&mps2_uart_driver, &mps_port->port);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, mps_port);
+
+	return 0;
+}
+
+static int mps2_serial_remove(struct platform_device *pdev)
+{
+	struct mps2_uart_port *mps_port = platform_get_drvdata(pdev);
+
+	uart_remove_one_port(&mps2_uart_driver, &mps_port->port);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id mps2_match[] = {
+	{ .compatible = "arm,mps2-uart", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, mps2_match);
+#endif
+
+static struct platform_driver mps2_serial_driver = {
+	.probe = mps2_serial_probe,
+	.remove = mps2_serial_remove,
+
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = of_match_ptr(mps2_match),
+	},
+};
+
+static int __init mps2_uart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&mps2_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&mps2_serial_driver);
+	if (ret)
+		uart_unregister_driver(&mps2_uart_driver);
+
+	return ret;
+}
+module_init(mps2_uart_init);
+
+static void __exit mps2_uart_exit(void)
+{
+	platform_driver_unregister(&mps2_serial_driver);
+	uart_unregister_driver(&mps2_uart_driver);
+}
+module_exit(mps2_uart_exit);
+
+MODULE_AUTHOR("Vladimir Murzin <vladimir.murzin@arm.com>");
+MODULE_DESCRIPTION("MPS2 UART driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:" DRIVER_NAME);

@@ -261,4 +261,7 @@
 /* STM32 USART */
 #define PORT_STM32	113
 
+/* MPS2 UART */
+#define PORT_MPS2UART	114
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */

@@ -883,6 +883,14 @@ config ARCH_STM32
 	help
 	  Support for STMicroelectronics STM32 processors.
 
+config ARCH_MPS2
+	bool "ARM MPS2 paltform"
+	depends on ARM_SINGLE_ARMV7M
+	select ARM_AMBA
+	select CLKSRC_MPS2
+	help
+	  Support for ARM MPS2 Cortex-M platform.
+
 # Definitions to make life easier
 config ARCH_ACORN
 	bool

@@ -182,6 +182,7 @@ machine-$(CONFIG_ARCH_LPC18XX)		+= lpc18xx
 machine-$(CONFIG_ARCH_LPC32XX)		+= lpc32xx
 machine-$(CONFIG_ARCH_MESON)		+= meson
 machine-$(CONFIG_ARCH_MMP)		+= mmp
+machine-$(CONFIG_ARCH_MPS2)		+= vexpress
 machine-$(CONFIG_ARCH_MOXART)		+= moxart
 machine-$(CONFIG_ARCH_MV78XX0)		+= mv78xx0
 machine-$(CONFIG_ARCH_MVEBU)		+= mvebu

@@ -4,7 +4,7 @@
 ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := \
 	-I$(srctree)/arch/arm/plat-versatile/include
 
-obj-y					:= v2m.o
+obj-$(CONFIG_ARCH_VEXPRESS)		:= v2m.o
 obj-$(CONFIG_ARCH_VEXPRESS_DCSCB)	+= dcscb.o	dcscb_setup.o
 CFLAGS_dcscb.o				+= -march=armv7-a
 CFLAGS_REMOVE_dcscb.o			= -pg

@@ -15,3 +15,5 @@ CFLAGS_tc2_pm.o				+= -march=armv7-a
 CFLAGS_REMOVE_tc2_pm.o			= -pg
 obj-$(CONFIG_SMP)			+= platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o
+
+obj-$(COFIG_ARCH_MPS2)			+= v2m-mps2.o

@@ -0,0 +1,3 @@
+# Empty file waiting for deletion once Makefile.boot isn't needed any more.
+# Patch waits for application at
+# http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .

@@ -0,0 +1,21 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <asm/mach/arch.h>
+
+static const char *const mps2_compat[] __initconst = {
+	"arm,mps2",
+	NULL
+};
+
+DT_MACHINE_START(MPS2DT, "MPS2 (Device Tree Support)")
+	.dt_compat = mps2_compat,
+MACHINE_END

@@ -245,7 +245,9 @@ dtb-$(CONFIG_ARCH_MMP) += \
 dtb-$(CONFIG_MACH_MESON8B) += \
 	meson8b-mxq.dtb \
 	meson8b-odroidc1.dtb
-dtb-$(CONFIG_ARCH_MPS2) += mps2-an385.dtb
+dtb-$(CONFIG_ARCH_MPS2) += \
+	mps2-an385.dtb \
+	mps2-an399.dtb
 dtb-$(CONFIG_ARCH_MOXART) += \
 	moxart-uc7112lx.dtb
 dtb-$(CONFIG_SOC_IMX1) += \

@@ -0,0 +1,92 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "mps2.dtsi"
+
+/ {
+	model = "ARM MPS2 Application Note 399/400";
+	compatible = "arm,mps2";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		bootargs = "rdinit=/sbin/init earlycon";
+		stdout-path = "serial0:9600n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x60000000 0x1000000>;
+	};
+
+	smb {
+		ethernet@1,0 {
+			compatible = "smsc,lan9220", "smsc,lan9115";
+			reg = <1 0x0 0x10000>;
+			interrupts = <13>;
+			interrupt-parent = <&nvic>;
+			smsc,irq-active-high;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&timer0 {
+	status = "okay";
+};
+
+&timer1 {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

@@ -1726,6 +1726,7 @@ F:	*/*/vexpress*
 F:	*/*/*/vexpress*
 F:	drivers/clk/versatile/clk-vexpress-osc.c
 F:	drivers/clocksource/versatile.c
+N:	mps2
 
 ARM/VFP SUPPORT
 M:	Russell King <linux@arm.linux.org.uk>

@@ -245,6 +245,7 @@ dtb-$(CONFIG_ARCH_MMP) += \
 dtb-$(CONFIG_MACH_MESON8B) += \
 	meson8b-mxq.dtb \
 	meson8b-odroidc1.dtb
+dtb-$(CONFIG_ARCH_MPS2) += mps2-an385.dtb
 dtb-$(CONFIG_ARCH_MOXART) += \
 	moxart-uc7112lx.dtb
 dtb-$(CONFIG_SOC_IMX1) += \

@@ -0,0 +1,92 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "mps2.dtsi"
+
+/ {
+	model = "ARM MPS2 Application Note 385/386";
+	compatible = "arm,mps2";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		bootargs = "rdinit=/sbin/init earlycon";
+		stdout-path = "serial0:9600n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x21000000 0x1000000>;
+	};
+
+	smb {
+		ethernet@0,0 {
+			compatible = "smsc,lan9220", "smsc,lan9115";
+			reg = <0 0x0 0x10000>;
+			interrupts = <13>;
+			interrupt-parent = <&nvic>;
+			smsc,irq-active-high;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&timer0 {
+	status = "okay";
+};
+
+&timer1 {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

@@ -0,0 +1,242 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "armv7-m.dtsi"
+
+/ {
+	oscclk0: clk-osc0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	oscclk1: clk-osc1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	oscclk2: clk-osc2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	cfgclk: clk-cfg {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <5000000>;
+	};
+
+	spicfgclk: clk-spicfg {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <75000000>;
+	};
+
+	sysclk: clk-sys {
+		compatible = "fixed-factor-clock";
+		clocks = <&oscclk0>;
+		#clock-cells = <0>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	audmclk: clk-audm {
+		compatible = "fixed-factor-clock";
+		clocks = <&oscclk1>;
+		#clock-cells = <0>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	audsclk: clk-auds {
+		compatible = "fixed-factor-clock";
+		clocks = <&oscclk1>;
+		#clock-cells = <0>;
+		clock-div = <8>;
+		clock-mult = <1>;
+	};
+
+	spiclcd: clk-cpiclcd {
+		compatible = "fixed-factor-clock";
+		clocks = <&oscclk0>;
+		#clock-cells = <0>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	spicon: clk-spicon {
+		compatible = "fixed-factor-clock";
+		clocks = <&oscclk0>;
+		#clock-cells = <0>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	i2cclcd: clk-i2cclcd {
+		compatible = "fixed-factor-clock";
+		clocks = <&oscclk0>;
+		#clock-cells = <0>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	i2caud: clk-i2caud {
+		compatible = "fixed-factor-clock";
+		clocks = <&oscclk0>;
+		#clock-cells = <0>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		ranges;
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40000000 0x10000>;
+
+			timer0: mps2-timer0@0 {
+				compatible = "arm,mps2-timer";
+				reg = <0x0 0x1000>;
+				interrupts = <8>;
+				clocks = <&sysclk>;
+				status = "disabled";
+			};
+
+			timer1: mps2-timer1@1000 {
+				compatible = "arm,mps2-timer";
+				reg = <0x1000 0x1000>;
+				interrupts = <9>;
+				clocks = <&sysclk>;
+				status = "disabled";
+			};
+
+			timer2: dual-timer@2000 {
+				compatible = "arm,sp804";
+				reg = <0x2000 0x1000>;
+				clocks = <&sysclk>;
+				interrupts = <10>;
+				status = "disabled";
+			};
+
+
+			uart0: serial@4000 {
+				compatible = "arm,mps2-uart";
+				reg = <0x4000 0x1000>;
+				interrupts = <0 1 12>;
+				clocks = <&sysclk>;
+				status = "disabled";
+			};
+
+			uart1: serial@5000 {
+				compatible = "arm,mps2-uart";
+				reg = <0x5000 0x1000>;
+				interrupts = <2 3 12>;
+				clocks = <&sysclk>;
+				status = "disabled";
+			};
+
+			uart2: serial@6000 {
+				compatible = "arm,mps2-uart";
+				reg = <0x6000 0x1000>;
+				interrupts = <4 5 12>;
+				clocks = <&sysclk>;
+				status = "disabled";
+			};
+
+			wdt: watchdog@8000 {
+				compatible = "arm,sp805", "arm,primecell";
+				arm,primecell-periphid = <0x00141805>;
+				reg = <0x8000 0x1000>;
+				interrupts = <0>;
+				clocks = <&sysclk>;
+				clock-names = "apb_pclk";
+				status = "disabled";
+			};
+		};
+	};
+
+	fpga {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x40020000 0x10000>;
+
+		fpgaio@8000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x8000 0x10>;
+
+			led@0 {
+				compatible = "register-bit-led";
+				offset = <0x0>;
+				mask = <0x01>;
+				label = "userled:0";
+				linux,default-trigger = "heartbeat";
+				default-state = "on";
+			};
+
+			led@1 {
+				compatible = "register-bit-led";
+				offset = <0x0>;
+				mask = <0x02>;
+				label = "userled:1";
+				linux,default-trigger = "usr";
+				default-state = "off";
+			};
+		};
+	};
+
+	smb {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x40200000 0x10000>,
+			 <1 0 0xa0000000 0x10000>;
+	};
+};

@@ -0,0 +1,109 @@
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_EXPERT=y
+# CONFIG_UID16 is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+# CONFIG_EPOLL is not set
+# CONFIG_SIGNALFD is not set
+# CONFIG_EVENTFD is not set
+# CONFIG_AIO is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_BLOCK is not set
+# CONFIG_MMU is not set
+CONFIG_ARCH_MPS2=y
+CONFIG_SET_MEM_PARAM=y
+CONFIG_DRAM_BASE=0x21000000
+CONFIG_DRAM_SIZE=0x1000000
+CONFIG_PREEMPT_VOLUNTARY=y
+# CONFIG_ATAGS is not set
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_SHARED_FLAT=y
+# CONFIG_COREDUMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_FW_LOADER is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_CORE is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_HISILICON is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+CONFIG_SMSC911X=y
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_NONSTANDARD=y
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_MPS2_UART_CONSOLE=y
+CONFIG_SERIAL_MPS2_UART=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ARM_SP805_WATCHDOG=y
+CONFIG_MFD_SYSCON=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_SYSCON=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_ARM_TIMER_SP804=y
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_V4_2=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_MEMTEST=y

@@ -1454,6 +1454,7 @@ config SERIAL_MPS2_UART_CONSOLE
 	bool "MPS2 UART console support"
 	depends on SERIAL_MPS2_UART
 	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
 
 config SERIAL_MPS2_UART
 	bool "MPS2 UART port"

@@ -439,6 +439,34 @@ static struct console mps2_uart_console = {
 
 #define MPS2_SERIAL_CONSOLE (&mps2_uart_console)
 
+static void mps2_early_putchar(struct uart_port *port, int ch)
+{
+
+	while (readb(port->membase + UARTn_STATE) & UARTn_STATE_TX_FULL)
+		cpu_relax();
+
+	writeb((unsigned char)ch, port->membase + UARTn_DATA);
+}
+
+static void mps2_early_write(struct console *con, const char *s, unsigned n)
+{
+	struct earlycon_device *dev = con->data;
+
+	uart_console_write(&dev->port, s, n, mps2_early_putchar);
+}
+
+static int __init mps2_early_console_setup(struct earlycon_device *device,
+					   const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = mps2_early_write;
+
+	return 0;
+}
+OF_EARLYCON_DECLARE(mps2, "arm,mps2-uart", mps2_early_console_setup);
+
 #else
 #define MPS2_SERIAL_CONSOLE NULL
 #endif

@@ -0,0 +1,19 @@
+ARM MPS2 UART
+
+Required properties:
+- compatible	: Should be "arm,mps2-uart"
+- reg		: Address and length of the register set
+- interrupts	: Reference to the UART RX, TX and overrun interrupts
+
+Required clocking property:
+- clocks	  : The input clock of the UART
+
+
+Examples:
+
+uart0: serial@40004000 {
+	compatible = "arm,mps2-uart";
+	reg = <0x40004000 0x1000>;
+	interrupts = <0 1 12>;
+	clocks = <&sysclk>;
+};