[PATCH v7 01/15] dt: power: bq24257-charger: Cover additional devices
From: Andreas Dannenberg <hidden>
Date: 2015-09-25 15:54:06
Also in:
linux-devicetree, linux-pm
Subsystem:
open firmware and flattened device tree bindings, the rest · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
Possibly related (same subject, not in this thread)
- 2015-09-28 · Re: [PATCH v7 01/15] dt: power: bq24257-charger: Cover additional devices · Sebastian Reichel <hidden>
- 2015-09-28 · Re: [PATCH v7 01/15] dt: power: bq24257-charger: Cover additional devices · Krzysztof Kozlowski <hidden>
Extend the bq24257 charger's device tree documentation to cover the bq24250 and bq24251 devices as well feature additions. Signed-off-by: Andreas Dannenberg <redacted> --- .../devicetree/bindings/power/bq24257.txt | 53 ++++++++++++++++++++-- 1 file changed, 48 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt
index 5c9d394..6c376ef 100644
--- a/Documentation/devicetree/bindings/power/bq24257.txt
+++ b/Documentation/devicetree/bindings/power/bq24257.txt@@ -1,21 +1,64 @@ -Binding for TI bq24257 Li-Ion Charger +Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger Required properties: - compatible: Should contain one of the following: + * "ti,bq24250" + * "ti,bq24251" * "ti,bq24257" -- reg: integer, i2c address of the device. +- reg: integer, i2c address of the device. +- interrupt-parent: Should be the phandle for the interrupt controller. Use in + conjunction with "interrupts". +- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in + conjunction with "interrupt-parent". - ti,battery-regulation-voltage: integer, maximum charging voltage in uV. -- ti,charge-current: integer, maximum charging current in uA. -- ti,termination-current: integer, charge will be terminated when current in - constant-voltage phase drops below this value (in uA). +- ti,charge-current: integer, maximum charging current in uA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA). + +Optional properties: +- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. +- ti,current-limit: The maximum current to be drawn from the charger's input + (in uA). If this property is not specified a USB D+/D- signal based charger + type detection is used (if available) and the input limit current is set + accordingly. If the D+/D- based detection is not available on a given device + a default of 500,000 is used (=500mA). +- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If + not specified a default of 6,5000,000 (=6.5V) is used. +- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic + power path management (in uV). If not specified a default of 4,360,000 + (=4.36V) is used. Example: bq24257 { compatible = "ti,bq24257"; reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; ti,battery-regulation-voltage = <4200000>; ti,charge-current = <1000000>; ti,termination-current = <50000>; }; + +Example: + +bq24250 { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; +};
--
1.9.1