inittab is not executing after my Linux box boots up | kernelnewbies

quoted

Hi

Please find the entire boot sequence here

*RomBOOT*
*
*
*
*
*U-Boot 1.3.4 (Mar  9 2010 - 19:35:35)*
*
*
*DRAM:  64 MB*
*NAND:  256 MiB*
*In:    serial*
*Out:   serial*
*Err:   serial*
*Net:   macb0*
*macb0: Starting autonegotiation...*
*macb0: Autonegotiation complete*
*macb0: link up, 100Mbps full-duplex (lpa: 0xc5e1)*
*Hit any key to stop autoboot:  0*
*U-Boot>*
*U-Boot> set bootcmd 'tftp 0x22200000 uImage; bootm 0x22200000'*
*U-Boot> set bootargs 'root=/dev/nfs nfsroot=10.0.0.1:/nfs ip=10.220.4.200:
:10.220.4.35:::eth0:off console=ttyS0,115200'*
*U-Boot> print*
*ethaddr=3a:1f:34:08:54:54*
*bootdelay=3*
*baudrate=115200*
*ethact=macb0*
*ipaddr=10.0.0.2*
*serverip=10.0.0.1*
*stdin=serial*
*stdout=serial*
*stderr=serial*
*bootcmd=tftp 0x22200000 uImage; bootm 0x22200000*
*bootargs=root=/dev/nfs nfsroot=10.0.0.1:/nfs
ip=10.220.4.200::10.220.4.35:::eth0:off
console=ttyS0,115200*
*
*
*Environment size: 297/131067 bytes*
*U-Boot> boot*
*macb0: link up, 100Mbps full-duplex (lpa: 0xc5e1)*
*Using macb0 device*
*TFTP from server 10.0.0.1; our IP address is 10.0.0.2*
*Filename 'uImage'.*
*Load address: 0x22200000*
*Loading: #################################################################*
*         #####################################################*
*done*
*Bytes transferred = 1720076 (1a3f0c hex)*
*## Booting kernel from Legacy Image at 22200000 ...*
*   Image Name:   Linux-2.6.37*
*   Image Type:   ARM Linux Kernel Image (uncompressed)*
*   Data Size:    1720012 Bytes =  1.6 MB*
*   Load Address: 20008000*
*   Entry Point:  20008000*
*   Verifying Checksum ... OK*
*   Loading Kernel Image ... OK*
*OK*
*
*
*Starting kernel ...*
*
*
*Uncompressing Linux... done, booting the kernel.*
*Linux version 2.6.37 (prajosh at prajosh) (gcc version 4.3.5 (Buildroot
2011.02) ) #2 Sun Jun 19 15:27:13 IST 2011*
*CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177*
*CPU: VIVT data cache, VIVT instruction cache*
*Machine: Atmel AT91SAM9G20-EK*
*Memory policy: ECC disabled, Data cache writeback*
*Clocks: CPU 396 MHz, master 132 MHz, main 18.432 MHz*
*Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256*
*Kernel command line: root=/dev/nfs nfsroot=10.0.0.1:/nfs ip=10.220.4.200:
:10.220.4.35:::eth0:off console=ttyS0,115200*
*PID hash table entries: 256 (order: -2, 1024 bytes)*
*Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)*
*Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)*
*Memory: 64MB = 64MB total*
*Memory: 61416k/61416k available, 4120k reserved, 0K highmem*
*Virtual kernel memory layout:*
*    vector  : 0xffff0000 - 0xffff1000   (   4 kB)*
*    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)*
*    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)*
*    vmalloc : 0xc4800000 - 0xfee00000   ( 934 MB)*
*    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)*
*    modules : 0xbf000000 - 0xc0000000   (  16 MB)*
*      .init : 0xc0008000 - 0xc0028000   ( 128 kB)*
*      .text : 0xc0028000 - 0xc032e0f8   (3097 kB)*
*      .data : 0xc0330000 - 0xc0350fe0   ( 132 kB)*
*NR_IRQS:192*
*AT91: 96 gpio irqs in 3 banks*
*Console: colour dummy device 80x30*
*console [ttyS0] enabled*
*Calibrating delay loop... 197.83 BogoMIPS (lpj=989184)*
*pid_max: default: 32768 minimum: 301*
*Mount-cache hash table entries: 512*
*CPU: Testing write buffer coherency: ok*
*NET: Registered protocol family 16*
*AT91: Power Management*
*AT91: Starting after user reset*
*bio: create slab <bio-0> at 0*
*SCSI subsystem initialized*
*usbcore: registered new interface driver usbfs*
*usbcore: registered new interface driver hub*
*usbcore: registered new device driver usb*
*Advanced Linux Sound Architecture Driver Version 1.0.23.*
*Switching to clocksource pit*
*NET: Registered protocol family 2*
*IP route cache hash table entries: 1024 (order: 0, 4096 bytes)*
*TCP established hash table entries: 2048 (order: 2, 16384 bytes)*
*TCP bind hash table entries: 2048 (order: 1, 8192 bytes)*
*TCP: Hash tables configured (established 2048 bind 2048)*
*TCP reno registered*
*UDP hash table entries: 256 (order: 0, 4096 bytes)*
*UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)*
*NET: Registered protocol family 1*
*RPC: Registered udp transport module.*
*RPC: Registered tcp transport module.*
*RPC: Registered tcp NFSv4.1 backchannel transport module.*
*NetWinder Floating Point Emulator V0.97 (double precision)*
*JFFS2 version 2.2. (NAND) (SUMMARY)  ?? 2001-2006 Red Hat, Inc.*
*msgmni has been set to 119*
*io scheduler noop registered (default)*
*atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL*
*atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL*
*atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL*
*brd: module loaded*
*loop: module loaded*
*NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung )*
*Scanning device for bad blocks*
*Bad eraseblock 532 at 0x000004280000*
*Bad eraseblock 1572 at 0x00000c480000*
*Creating 3 MTD partitions on "atmel_nand":*
*0x000000000000-0x000000400000 : "Bootstrap"*
*0x000000400000-0x000004000000 : "Partition 1"*
*0x000004000000-0x000010000000 : "Partition 2"*
*atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12)*
*atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffcc000 (irq 13)*
*MACB_mii_bus: probed*
*eth0: Atmel MACB at 0xfffc4000 irq 21 (3a:1f:34:08:54:54)*
*eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00,
irq=-1)*
*usbmon: debugfs is not available*
*ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver*
*at91_ohci at91_ohci: AT91 OHCI*
*at91_ohci at91_ohci: new USB bus registered, assigned bus number 1*
*at91_ohci at91_ohci: irq 20, io mem 0x00500000*
*hub 1-0:1.0: USB hub found*
*hub 1-0:1.0: 2 ports detected*
*Initializing USB Mass Storage driver...*
*usbcore: registered new interface driver usb-storage*
*USB Mass Storage support registered.*
*udc: at91_udc version 3 May 2006*
*mice: PS/2 mouse device common for all mice*
*input: gpio-keys as /devices/platform/gpio-keys/input/input0*
*rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0*
*rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!*
*usbcore: registered new interface driver usbhid*
*usbhid: USB HID core driver*
*ALSA device list:*
*  No soundcards found.*
*TCP cubic registered*
*NET: Registered protocol family 17*
*rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock*
*IP-Config: Guessing netmask 255.0.0.0*
*IP-Config: Complete:*
*     device=eth0, addr=10.220.4.200, mask=255.0.0.0, gw=10.220.4.35,*
*     host=10.220.4.200, domain=, nis-domain=(none),*
*     bootserver=255.255.255.255, rootserver=10.0.0.1, rootpath=*
*eth0: link up (100/Full)*
*VFS: Mounted root (nfs filesystem) on device 0:12.*
*Freeing init memory: 128K*
*Starting network...*
*ip: RTNETLINK answers: File exists*
*Starting dropbear sshd: generating rsa key... generating dsa key... OK*

I have put down the entire sequence. I have also shown the
u-boot parameters.

Could anybody please tell me why the board stops after the command. I have
the same file system flashed on my NAND flash and if i show that path for
the boot operation every thing works fine. (i.e. i load the kernel on tftp
and boot from that.)

Regards
Prajosh Premdas

On Wed, Jun 15, 2011 at 12:10 PM, Raseel Bhagat [off-list ref]wrote:

`h`	back out one level
`j`	next message in thread
`k`	previous message in thread
`l`	drill in
`Esc`	close help / fold thread tree
`?`	toggle this help