# Re: \[PATCH net-next 1/2\] dt-bindings: dpll: Add clock ID property

- From: Krzysztof Kozlowski \<krzk@kernel.org\>
- Date: 2025-08-03 11:12:49 
- List: netdev
- Page: https://ratatoskr.run/netdev/2025/08/3156851
- Thread: https://ratatoskr.run/netdev/2025/07/3139001/t.md

```text
On 23/07/2025 09:23, Ivan Vecera wrote:
> 
> 
> On 23. 07. 25 8:25 dop., Krzysztof Kozlowski wrote:
>> On 21/07/2025 14:54, Ivan Vecera wrote:
>>> On 21. 07. 25 11:23 dop., Krzysztof Kozlowski wrote:
>>>> On Fri, Jul 18, 2025 at 02:16:41PM +0200, Ivan Vecera wrote:
>>>>> Hi Krzysztof,
>>>>>
>>>>> ...
>>>>>
>>>>> The clock-id property name may have been poorly chosen. This ID is used by
>>>>> the DPLL subsystem during the registration of a DPLL channel, along with its
>>>>> channel ID. A driver that provides DPLL functionality can compute this
>>>>> clock-id from any unique chip information, such as a serial number.
>>>>>
>>>>> Currently, other drivers that implement DPLL functionality are network
>>>>> drivers, and they generate the clock-id from one of their MAC addresses by
>>>>> extending it to an EUI-64.
>>>>>
>>>>> A standalone DPLL device, like the zl3073x, could use a unique property such
>>>>> as its serial number, but the zl3073x does not have one. This patch-set is
>>>>> motivated by the need to support such devices by allowing the DPLL device ID
>>>>> to be passed via the Device Tree (DT), which is similar to how NICs without
>>>>> an assigned MAC address are handled.
>>>>
>>>> You use words like "unique" and MAC, thus I fail to see how one fixed
>>>> string for all boards matches this. MACs are unique. Property value set
>>>> in DTS for all devices is not.
>>>>> You also need to explain who assigns this value (MACs are assigned) or
>>>> if no one, then why you cannot use random? I also do not see how this
>>>> property solves this...  One person would set it to value "1", other to
>>>> "2" but third decide to reuse "1"? How do you solve it for all projects
>>>> in the upstream?
>>>
>>> Some background: Any DPLL driver has to use a unique number during the
>>> DPLL device/channel registration. The number must be unique for the
>>> device across a clock domain (e.g., a single PTP network).
>>>
>>> NIC drivers that expose DPLL functionality usually use their MAC address
>>> to generate such a unique ID. A standalone DPLL driver does not have
>>> this option, as there are no NIC ports and therefore no MAC addresses.
>>> Such a driver can use any other source for the ID (e.g., the chip's
>>> serial number). Unfortunately, this is not the case for zl3073x-based
>>> hardware, as its current firmware revisions do not expose information
>>> that could be used to generate the clock ID (this may change in the
>>> future).
>>>
>>> There is no authority that assigns clock ID value ranges similarly to
>>> MAC addresses (OUIs, etc.), but as mentioned above, uniqueness is
>>> required across a single PTP network so duplicates outside this
>>> single network are not a problem.
>>
>> You did not address main concern. You will configure the same value for
>> all boards, so how do you solve uniqueness within PTP network?
> 
> This value differs across boards, similar to the local-mac-address. The
> device tree specifies the entry, and the bootloader or system firmware
> (like U-Boot) provides the actual value.
This should be clearly explained in commit msg or pull request to dtschema.

Where are patches for U-Boot? lore gives me 0 results.

Best regards,
Krzysztof
```
