# Re: \[PATCH V2 3/4\] vp\_vdpa: allow set vq state to initial state after reset

- From: Jason Wang \<hidden\>
- Date: 2021-06-02 07:05:52 
- List: netdev
- Page: https://ratatoskr.run/netdev/2021/06/1399390
- Thread: https://ratatoskr.run/kvm/2021/06/1399191/t.md

```text

在 2021/6/2 下午2:13, Eli Cohen 写道:
> On Wed, Jun 02, 2021 at 10:10:42AM +0800, Jason Wang wrote:
>> We used to fail the set_vq_state() since it was not supported yet by
>> the virtio spec. But if the bus tries to set the state which is equal
>> to the device initial state after reset, we can let it go.
>>
>> This is a must for virtio_vdpa() to set vq state during probe which is
>> required for some vDPA parents.
>>
>> Signed-off-by: Jason Wang <redacted>
>> ---
>>   drivers/vdpa/virtio_pci/vp_vdpa.c | 42 ++++++++++++++++++++++++++++---
>>   1 file changed, 39 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/vdpa/virtio_pci/vp_vdpa.c b/drivers/vdpa/virtio_pci/vp_vdpa.c
>> index c76ebb531212..18bf4a422772 100644
>> --- a/drivers/vdpa/virtio_pci/vp_vdpa.c
>> +++ b/drivers/vdpa/virtio_pci/vp_vdpa.c
>> @@ -210,13 +210,49 @@ static int vp_vdpa_get_vq_state(struct vdpa_device *vdpa, u16 qid,
>>   	return -EOPNOTSUPP;
>>   }
>>   
>> +static int vp_vdpa_set_vq_state_split(struct vdpa_device *vdpa,
>> +				      const struct vdpa_vq_state *state)
>> +{
>> +	const struct vdpa_vq_state_split *split = &state->split;
>> +
>> +	if (split->avail_index == 0)
>> +		return 0;
>> +
>> +	return -EOPNOTSUPP;
>> +}
>> +
>> +static int vp_vdpa_set_vq_state_packed(struct vdpa_device *vdpa,
>> +				       const struct vdpa_vq_state *state)
>> +{
>> +	const struct vdpa_vq_state_packed *packed = &state->packed;
>> +
>> +	if (packed->last_avail_counter == 1 &&
> Can you elaborate on the requirement on last_avail_counter and
> last_used_counter?


This is required by the virtio spec:

"
2.7.1 Driver and Device Ring Wrap Counters
Each of the driver and the device are expected to maintain, internally, a single-bit ring wrap counter initialized to 1.
"

For virtio-pci device, since there's no way to assign the value of those counters, the counters will be reset to 1 after reset, otherwise the driver can't work.

Thanks


>
>> +	    packed->last_avail_idx == 0 &&
>> +	    packed->last_used_counter == 1 &&
>> +	    packed->last_used_idx == 0)
>> +		return 0;
>> +
>> +	return -EOPNOTSUPP;
>> +}
>> +
>>   static int vp_vdpa_set_vq_state(struct vdpa_device *vdpa, u16 qid,
>>   				const struct vdpa_vq_state *state)
>>   {
>> -	/* Note that this is not supported by virtio specification, so
>> -	 * we return -ENOPOTSUPP here. This means we can't support live
>> -	 * migration, vhost device start/stop.
>> +	struct virtio_pci_modern_device *mdev = vdpa_to_mdev(vdpa);
>> +
>> +	/* Note that this is not supported by virtio specification.
>> +	 * But if the state is by chance equal to the device initial
>> +	 * state, we can let it go.
>>   	 */
>> +	if ((vp_modern_get_status(mdev) & VIRTIO_CONFIG_S_FEATURES_OK) &&
>> +	    !vp_modern_get_queue_enable(mdev, qid)) {
>> +		if (vp_modern_get_driver_features(mdev) &
>> +		    BIT_ULL(VIRTIO_F_RING_PACKED))
>> +			return vp_vdpa_set_vq_state_packed(vdpa, state);
>> +		else
>> +			return vp_vdpa_set_vq_state_split(vdpa,	state);
>> +	}
>> +
>>   	return -EOPNOTSUPP;
>>   }
>>   
>> -- 
>> 2.25.1
>>

```