[PATCH v2 0/2] usb: add full support for ZTE P685M modem

This modem is used in ZTE MF283+ LTE SOHO router, and carriers usually
identify it as such. This series is a part of effort to get this router
fully supported by OpenWrt. With this series, all interfaces of the modem
are fully supported, and it can establish connection through QMI interface.


Lech Perczak (2):
  net: usb: qmi_wwan: support ZTE P685M modem
  usb: serial: option: add full support for ZTE P685M

 drivers/net/usb/qmi_wwan.c  | 1 +
 drivers/usb/serial/option.c | 2 +-
 2 files changed, 2 insertions(+), 1 deletion(-)

-- 
2.20.1

The modem is used inside ZTE MF283+ router and carriers identify it as
such.
Interface mapping is:
0: QCDM, 1: AT (PCUI), 2: AT (Modem), 3: QMI, 4: ADB

T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1275 Rev=f0.00
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE Technologies MSM
S:  SerialNumber=P685M510ZTED0000CP&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&0
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=87(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lech Perczak <redacted>
---
v2: no changes to this patch, resend as series.

 drivers/net/usb/qmi_wwan.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
index cc4819282820..a0bf7737402f 100644
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c

@@ -1235,6 +1235,7 @@ static const struct usb_device_id products[] = {
 	{QMI_FIXED_INTF(0x19d2, 0x1255, 4)},
 	{QMI_FIXED_INTF(0x19d2, 0x1256, 4)},
 	{QMI_FIXED_INTF(0x19d2, 0x1270, 5)},	/* ZTE MF667 */
+	{QMI_FIXED_INTF(0x19d2, 0x1275, 3)},	/* ZTE P685M */
 	{QMI_FIXED_INTF(0x19d2, 0x1401, 2)},
 	{QMI_FIXED_INTF(0x19d2, 0x1402, 2)},	/* ZTE MF60 */
 	{QMI_FIXED_INTF(0x19d2, 0x1424, 2)},

-- 
2.20.1

Only 1st (DIAG) port was supported, support ports 1 (PCUI) and 2 (Modem)
on ff/00/00 too. Ports expose AT command interface. Blacklist ports 3
now used by qmi_wwan and port 4 for ADB, and finally simplify device ID
to match only ports 0-2.

The modem is used inside ZTE MF283+ router and carriers identify it as
such.
Interface mapping is:
0: QCDM, 1: AT (PCUI), 2: AT (Modem), 3: QMI, 4: ADB

T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1275 Rev=f0.00
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE Technologies MSM
S:  SerialNumber=P685M510ZTED0000CP&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&0
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=87(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Cc: Johan Hovold <johan@kernel.org>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lech Perczak <redacted>

---
v2: Blacklist ports 3-4 and simplify device ID,
as suggested by Lars Melin.

 drivers/usb/serial/option.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 3fe959104311..485d07df8f69 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c

@@ -1567,7 +1567,7 @@ static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1272, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1273, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1274, 0xff, 0xff, 0xff) },
-	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1275, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE(ZTE_VENDOR_ID, 0x1275), .driver_info = RSVD(3) | RSVD(4) }, /* ZTE P685M */
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1276, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1277, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1278, 0xff, 0xff, 0xff) },

-- 
2.20.1