On Mon, Jan 8, 2018 at 10:48 PM, [off-list ref] wrote:
quoted
From: Keefe Liu <redacted>
The MTU of ipvlan interface should not bigger than the phy device,
When we run following scripts, we will find there are some problems.
Step1:
ip link add link eth0 name ipv1 type ipvlan mode l2
ip netns add net1
ip link set dev ipv1 netns net1
Step2:
ip netns exec net1 ip link set dev ipv1 mtu 1501
RTNETLINK answers: Invalid argument
dmesg info: "ipv1: Invalid MTU 1501 requested, hw max 1500"
Step3:
ip link set dev eth0 mtu 1600
ip netns exec net1 ip link set dev ipv1 mtu 1501
RTNETLINK answers: Invalid argument
dmesg info: "ipv1: Invalid MTU 1501 requested, hw max 1500"
Step4:
ip link set dev eth0 mtu 1400
ip netns exec net1 ip link set dev ipv1 mtu 1500 The result of
Step2 is we expected, but the result of Step3 and Step4 are not.
This patch set ipvlan's maximum MTU to ETH_MAX_MTU, and when we
change
quoted
the ipvlan device's MTU, ipvlan_change_mtu() will make sure the new
MTU no larger than the phy device's MTU.
Signed-off-by: Keefe Liu <redacted>
---
drivers/net/ipvlan/ipvlan_main.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/net/ipvlan/ipvlan_main.c
b/drivers/net/ipvlan/ipvlan_main.c
index 30cb803..84c007d 100644
--- a/drivers/net/ipvlan/ipvlan_main.c
+++ b/drivers/net/ipvlan/ipvlan_main.c
@@ -380,12 +380,24 @@ static int ipvlan_get_iflink(const struct net_device
*dev)
quoted
return ipvlan->phy_dev->ifindex; }
+static int ipvlan_change_mtu(struct net_device *dev, int new_mtu) {
+ struct ipvl_dev *ipvlan = netdev_priv(dev);
+
+ if (ipvlan->phy_dev->mtu < new_mtu)
+ return -EINVAL;
+
+ dev->mtu = new_mtu;
+ return 0;
+}
+
static const struct net_device_ops ipvlan_netdev_ops = {
.ndo_init = ipvlan_init,
.ndo_uninit = ipvlan_uninit,
.ndo_open = ipvlan_open,
.ndo_stop = ipvlan_stop,
.ndo_start_xmit = ipvlan_start_xmit,
+ .ndo_change_mtu = ipvlan_change_mtu,
.ndo_fix_features = ipvlan_fix_features,
.ndo_change_rx_flags = ipvlan_change_rx_flags,
.ndo_set_rx_mode = ipvlan_set_multicast_mac_filter,@@ -680,6 +692,8 @@ void ipvlan_link_setup(struct net_device *dev) {
ether_setup(dev);
+ dev->min_mtu = 0;
should be ETH_MIN_MTU since we expect the underlying device to be
ETH_ARPHDR and IPvlan deals with IPv4/IPv6.
[liuqifa] Yes, I agree with you. But I have another question, I found in commit 9157208, macvlan's min_mtu has been changed from ETH_MIN_MTU to 0, I'd like to know what's the difference between macvlan and ipvlan.
quoted
+ dev->max_mtu = ETH_MAX_MTU;
dev->priv_flags &= ~(IFF_XMIT_DST_RELEASE | IFF_TX_SKB_SHARING);
dev->priv_flags |= IFF_UNICAST_FLT | IFF_NO_QUEUE;
dev->netdev_ops = &ipvlan_netdev_ops;
--
1.8.3.1
These changes are not sufficient if you want to have different per-slave mtu
settings. One can always change the MTU of the master device and all per-
slave settings will get wiped. I don't think that's a desired outcome.
[liuqifa] I agree with you, I will reprogram the code to realize this goal.
On Tue, Jan 9, 2018 at 7:12 PM, liuqifa [off-list ref] wrote:
quoted
On Mon, Jan 8, 2018 at 10:48 PM, [off-list ref] wrote:
quoted
From: Keefe Liu <redacted>
The MTU of ipvlan interface should not bigger than the phy device,
When we run following scripts, we will find there are some problems.
Step1:
ip link add link eth0 name ipv1 type ipvlan mode l2
ip netns add net1
ip link set dev ipv1 netns net1
Step2:
ip netns exec net1 ip link set dev ipv1 mtu 1501
RTNETLINK answers: Invalid argument
dmesg info: "ipv1: Invalid MTU 1501 requested, hw max 1500"
Step3:
ip link set dev eth0 mtu 1600
ip netns exec net1 ip link set dev ipv1 mtu 1501
RTNETLINK answers: Invalid argument
dmesg info: "ipv1: Invalid MTU 1501 requested, hw max 1500"
Step4:
ip link set dev eth0 mtu 1400
ip netns exec net1 ip link set dev ipv1 mtu 1500 The result of
Step2 is we expected, but the result of Step3 and Step4 are not.
This patch set ipvlan's maximum MTU to ETH_MAX_MTU, and when we
change
quoted
the ipvlan device's MTU, ipvlan_change_mtu() will make sure the new
MTU no larger than the phy device's MTU.
Signed-off-by: Keefe Liu <redacted>
---
drivers/net/ipvlan/ipvlan_main.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/net/ipvlan/ipvlan_main.c
b/drivers/net/ipvlan/ipvlan_main.c
index 30cb803..84c007d 100644
--- a/drivers/net/ipvlan/ipvlan_main.c
+++ b/drivers/net/ipvlan/ipvlan_main.c
@@ -380,12 +380,24 @@ static int ipvlan_get_iflink(const struct net_device
*dev)
quoted
return ipvlan->phy_dev->ifindex; }
+static int ipvlan_change_mtu(struct net_device *dev, int new_mtu) {
+ struct ipvl_dev *ipvlan = netdev_priv(dev);
+
+ if (ipvlan->phy_dev->mtu < new_mtu)
+ return -EINVAL;
+
+ dev->mtu = new_mtu;
+ return 0;
+}
+
static const struct net_device_ops ipvlan_netdev_ops = {
.ndo_init = ipvlan_init,
.ndo_uninit = ipvlan_uninit,
.ndo_open = ipvlan_open,
.ndo_stop = ipvlan_stop,
.ndo_start_xmit = ipvlan_start_xmit,
+ .ndo_change_mtu = ipvlan_change_mtu,
.ndo_fix_features = ipvlan_fix_features,
.ndo_change_rx_flags = ipvlan_change_rx_flags,
.ndo_set_rx_mode = ipvlan_set_multicast_mac_filter,@@ -680,6 +692,8 @@ void ipvlan_link_setup(struct net_device *dev) {
ether_setup(dev);
+ dev->min_mtu = 0;
should be ETH_MIN_MTU since we expect the underlying device to be
ETH_ARPHDR and IPvlan deals with IPv4/IPv6.
[liuqifa] Yes, I agree with you. But I have another question, I found in commit 9157208, macvlan's min_mtu has been changed from ETH_MIN_MTU to 0, I'd like to know
what's the difference between macvlan and ipvlan.
IPvlan uses L3 address for its demux logic and min-L3-mtu set to be
ETH_MIN_MTU (68) for IPv4 packets with ip-options which no one uses
them now. Practically for IPvlan to operate, the header need be =
ether_hdr (14) + max(IPv4 hdr, IPv6 hdr) 40 = 54. So MTU which
includes HDRs + payload need to be more than 54. Same principle
applies to Macvlan except that its demux logic uses L2 instead of L3
(as in case of IPvlan). I don't know the motive behind setting it to 0
in macvlan.
quoted
quoted
+ dev->max_mtu = ETH_MAX_MTU;
dev->priv_flags &= ~(IFF_XMIT_DST_RELEASE | IFF_TX_SKB_SHARING);
dev->priv_flags |= IFF_UNICAST_FLT | IFF_NO_QUEUE;
dev->netdev_ops = &ipvlan_netdev_ops;
--
1.8.3.1
These changes are not sufficient if you want to have different per-slave mtu
settings. One can always change the MTU of the master device and all per-
slave settings will get wiped. I don't think that's a desired outcome.
[liuqifa] I agree with you, I will reprogram the code to realize this goal.
I suggest you use the 'mtu_adj' per slave device that I had in the
code for the exact same reasons that you are implementing. I never got
around completing it (it was deleted in later updates), but you can
re-add that field. So when when ndo_change_mtu is invoked for a slave,
you recalculate 'mtu_adj' field and when ndo_change_mtu is called for
master, you adjust this field for all of the slaves. This will make
ndo_change_mtu work on both slave as well master without causing
issues.