e1000e on Thinkpad x60: gigabit not available due to "SmartSpeed"

Hi!

I have trouble getting 1000mbit out of my ethernet card.

I tried direct connection between two PCs with different cables, and
no luck.

Today I tried connection to 1000mbit switch, and no luck, either. (Two
cables, one was cat6, both short).

My computer sees 1000mbit being advertised by the other side, but does
not advertise 1000mbit, "Link Speed was downgraded by SmartSpeed".

4.8.0-rc4+ kernel.

Does it work for other people? Card is:

02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet
Controller

root@duo:/data/l/linux# mii-tool -v eth1
SIOCGMIIREG on eth1 failed: Input/output error
SIOCGMIIREG on eth1 failed: Input/output error
eth1: negotiated 100baseTx-FD, link ok
  product info: Yukon-EC 88E1111 rev 0
  basic mode:   autonegotiation enabled
  basic status: autonegotiation complete, link ok
  capabilities: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
  advertising:  100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
  link partner: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
root@duo:/data/l/linux#

[ 1330.622658] e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow
Control: None
[ 1330.622840] e1000e 0000:02:00.0 eth1: Link Speed was downgraded by
SmartSpeed
[ 1330.622846] e1000e 0000:02:00.0 eth1: 10/100 speed: disabling TSO
root@duo:/data/l/linux#

Best regards,

									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

On Thu, 2016-09-01 at 22:14 +0200, Pavel Machek wrote:

Hi!

I have trouble getting 1000mbit out of my ethernet card.

I tried direct connection between two PCs with different cables, and
no luck.

Today I tried connection to 1000mbit switch, and no luck, either. (Two
cables, one was cat6, both short).

My computer sees 1000mbit being advertised by the other side, but does
not advertise 1000mbit, "Link Speed was downgraded by SmartSpeed".

Check your cables?

https://vmxp.wordpress.com/2015/01/06/1gbe-intel-nic-throttled-to-100mbit-by-smartspeed/

- Greg

4.8.0-rc4+ kernel.

Does it work for other people? Card is:

02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet
Controller

root@duo:/data/l/linux# mii-tool -v eth1
SIOCGMIIREG on eth1 failed: Input/output error
SIOCGMIIREG on eth1 failed: Input/output error
eth1: negotiated 100baseTx-FD, link ok
  product info: Yukon-EC 88E1111 rev 0
  basic mode:   autonegotiation enabled
  basic status: autonegotiation complete, link ok
  capabilities: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
  advertising:  100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
  link partner: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
root@duo:/data/l/linux#

[ 1330.622658] e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow
Control: None
[ 1330.622840] e1000e 0000:02:00.0 eth1: Link Speed was downgraded by
SmartSpeed
[ 1330.622846] e1000e 0000:02:00.0 eth1: 10/100 speed: disabling TSO
root@duo:/data/l/linux#

Best regards,

									Pavel

On Thu, Sep 01, 2016 at 02:58:13PM -0700, Greg wrote:

On Thu, 2016-09-01 at 22:14 +0200, Pavel Machek wrote:

quoted

Hi!

I have trouble getting 1000mbit out of my ethernet card.

I tried direct connection between two PCs with different cables, and
no luck.

Today I tried connection to 1000mbit switch, and no luck, either. (Two
cables, one was cat6, both short).

My computer sees 1000mbit being advertised by the other side, but does
not advertise 1000mbit, "Link Speed was downgraded by SmartSpeed".

Check your cables?

https://vmxp.wordpress.com/2015/01/06/1gbe-intel-nic-throttled-to-100mbit-by-smartspeed/

Of course if it isn't the cable, then it could even be a broken pin in
the port.  As far as I can tell, anything that causes one of the 3rd
or 4th pairs of wires to not work will degrade to 100Mbit on just the
first 2 pairs of wires and give that message.  Some badly implemented
switches can also cause it of course.

-- 
Len Sorensen

On Fri 2016-09-02 12:57:35, Lennart Sorensen wrote:

On Thu, Sep 01, 2016 at 02:58:13PM -0700, Greg wrote:

quoted

On Thu, 2016-09-01 at 22:14 +0200, Pavel Machek wrote:

quoted

Hi!

I have trouble getting 1000mbit out of my ethernet card.

I tried direct connection between two PCs with different cables, and
no luck.

Today I tried connection to 1000mbit switch, and no luck, either. (Two
cables, one was cat6, both short).

My computer sees 1000mbit being advertised by the other side, but does
not advertise 1000mbit, "Link Speed was downgraded by SmartSpeed".

Check your cables?

https://vmxp.wordpress.com/2015/01/06/1gbe-intel-nic-throttled-to-100mbit-by-smartspeed/

Of course if it isn't the cable, then it could even be a broken pin in
the port.  As far as I can tell, anything that causes one of the 3rd
or 4th pairs of wires to not work will degrade to 100Mbit on just the
first 2 pairs of wires and give that message.  Some badly implemented
switches can also cause it of course.

Ok, so it seems like broken pin in the port. I realized I had docking
station available for the machine, and when connecting using that
connector (not internal notebook one), I get gigabit speed.

Thanks and best regards,
								Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html