[PATCH] at803x: fix suspend/resume for SGMII link
From: Zefir Kurtisi <hidden>
Date: 2016-03-11 14:40:50
When operating the at803x in SGMII mode, resuming the chip from power down brings up the copper-side link but leaves the SGMII link in unconnected state (tested with at8031 attached to gianfar). In effect, this caused a permanent link loss once the related interface was put down. This patch ensures that power down handling in supspend() and resume() is also applied to the SGMII link. Signed-off-by: Zefir Kurtisi <redacted> --- drivers/net/phy/at803x.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 2174ec9..1e901c7 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c@@ -52,6 +52,9 @@ #define AT803X_DEBUG_REG_5 0x05 #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) +#define AT803X_REG_CHIP_CONFIG 0x1f +#define AT803X_BT_BX_REG_SEL 0x8000 + #define ATH8030_PHY_ID 0x004dd076 #define ATH8031_PHY_ID 0x004dd074 #define ATH8035_PHY_ID 0x004dd072
@@ -206,6 +209,7 @@ static int at803x_suspend(struct phy_device *phydev) { int value; int wol_enabled; + int ccr; mutex_lock(&phydev->lock);
@@ -221,6 +225,16 @@ static int at803x_suspend(struct phy_device *phydev) phy_write(phydev, MII_BMCR, value); + if (phydev->interface != PHY_INTERFACE_MODE_SGMII) + goto done; + + /* also power-down SGMII interface */ + ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG); + phy_write(phydev, AT803X_REG_CHIP_CONFIG, ccr & ~AT803X_BT_BX_REG_SEL); + phy_write(phydev, MII_BMCR, phy_read(phydev, MII_BMCR) | BMCR_PDOWN); + phy_write(phydev, AT803X_REG_CHIP_CONFIG, ccr | AT803X_BT_BX_REG_SEL); + +done: mutex_unlock(&phydev->lock); return 0;
@@ -229,6 +243,7 @@ static int at803x_suspend(struct phy_device *phydev) static int at803x_resume(struct phy_device *phydev) { int value; + int ccr; mutex_lock(&phydev->lock);
@@ -236,6 +251,17 @@ static int at803x_resume(struct phy_device *phydev) value &= ~(BMCR_PDOWN | BMCR_ISOLATE); phy_write(phydev, MII_BMCR, value); + if (phydev->interface != PHY_INTERFACE_MODE_SGMII) + goto done; + + /* also power-up SGMII interface */ + ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG); + phy_write(phydev, AT803X_REG_CHIP_CONFIG, ccr & ~AT803X_BT_BX_REG_SEL); + value = phy_read(phydev, MII_BMCR) & ~(BMCR_PDOWN | BMCR_ISOLATE); + phy_write(phydev, MII_BMCR, value); + phy_write(phydev, AT803X_REG_CHIP_CONFIG, ccr | AT803X_BT_BX_REG_SEL); + +done: mutex_unlock(&phydev->lock); return 0;
--
2.7.0