[PATCH v2 1/3] net: macb: Document zynq gem dt binding

---
 drivers/net/ethernet/cadence/macb.c |   12 ++++++++++++
 drivers/net/ethernet/cadence/macb.h |    1 +
 2 files changed, 13 insertions(+)

diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c
index 61aa570..e7c0ef6 100644
--- a/drivers/net/ethernet/cadence/macb.c
+++ b/drivers/net/ethernet/cadence/macb.c

@@ -350,6 +350,9 @@ static int macb_mii_probe(struct net_device *dev)
 	else
 		phydev->supported &= PHY_BASIC_FEATURES;
 
+	if (bp->caps & MACB_CAPS_NO_GIGABIT_HALF)
+		phydev->supported &= ~SUPPORTED_1000baseT_Half;
+
 	phydev->advertising = phydev->supported;
 
 	bp->link = 0;

@@ -2693,6 +2696,14 @@ static const struct macb_config emac_config = {
 	.init = at91ether_init,
 };
 
+static const struct macb_config zynq_config = {
+	.caps = MACB_CAPS_SG_DISABLED | MACB_CAPS_GIGABIT_MODE_AVAILABLE |
+		MACB_CAPS_NO_GIGABIT_HALF,
+	.dma_burst_length = 16,
+	.clk_init = macb_clk_init,
+	.init = macb_init,
+};
+
 static const struct of_device_id macb_dt_ids[] = {
 	{ .compatible = "cdns,at32ap7000-macb" },
 	{ .compatible = "cdns,at91sam9260-macb", .data = &at91sam9260_config },

@@ -2703,6 +2714,7 @@ static const struct of_device_id macb_dt_ids[] = {
 	{ .compatible = "atmel,sama5d4-gem", .data = &sama5d4_config },
 	{ .compatible = "cdns,at91rm9200-emac", .data = &emac_config },
 	{ .compatible = "cdns,emac", .data = &emac_config },
+	{ .compatible = "cdns,zynq-gem", .data = &zynq_config },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, macb_dt_ids);

diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index eb7d76f..24b1d9b 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h

@@ -393,6 +393,7 @@
 #define MACB_CAPS_ISR_CLEAR_ON_WRITE		0x00000001
 #define MACB_CAPS_USRIO_HAS_CLKEN		0x00000002
 #define MACB_CAPS_USRIO_DEFAULT_IS_MII		0x00000004
+#define MACB_CAPS_NO_GIGABIT_HALF		0x00000008
 #define MACB_CAPS_FIFO_MODE			0x10000000
 #define MACB_CAPS_GIGABIT_MODE_AVAILABLE	0x20000000
 #define MACB_CAPS_SG_DISABLED			0x40000000

---
 Documentation/devicetree/bindings/net/cdns-emac.txt |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt
index abd67c1..4451ee9 100644
--- a/Documentation/devicetree/bindings/net/cdns-emac.txt
+++ b/Documentation/devicetree/bindings/net/cdns-emac.txt

@@ -3,7 +3,8 @@
 Required properties:
 - compatible: Should be "cdns,[<chip>-]{emac}"
   Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
-  or the generic form: "cdns,emac".
+  Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
+  Or the generic form: "cdns,emac".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt
 - phy-mode: see ethernet.txt file in the same directory.

Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.

Signed-off-by: Nathan Sullivan <redacted>
---
 arch/arm/boot/dts/zynq-7000.dtsi |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
index a5cd2ed..9ea54b3 100644
--- a/arch/arm/boot/dts/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/zynq-7000.dtsi

@@ -193,7 +193,7 @@
 		};
 
 		gem0: ethernet@e000b000 {
-			compatible = "cdns,gem";
+			compatible = "cdns,zynq-gem";

 			reg = <0xe000b000 0x1000>;
 			status = "disabled";
 			interrupts = <0 22 4>;

@@ -204,7 +204,7 @@
 		};
 
 		gem1: ethernet@e000c000 {
-			compatible = "cdns,gem";
+			compatible = "cdns,zynq-gem";