[PATCH net-next 0/6] at86rf230: cleanups and add missing devicetree documentation

@@ -557,11 +557,12 @@ at86rf230_state(struct ieee802154_dev *dev, int state)
 	    (desired_status == STATE_RX_AACK_ON && val == STATE_BUSY_RX_AACK))
 		return 0;
 
-	pr_err("unexpected state change: %d, asked for %d\n", val, state);
+	dev_err(&lp->spi->dev, "unexpected state change: %d, asked for %d\n",
+		val, state);
 	return -EBUSY;
 
 err:
-	pr_err("error: %d\n", rc);
+	dev_err(&lp->spi->dev, "error: %d\n", rc);
 	return rc;
 }
 

@@ -699,7 +700,7 @@ at86rf230_xmit(struct ieee802154_dev *dev, struct sk_buff *skb)
 err_rx:
 	at86rf230_start(dev);
 err:
-	pr_err("error: %d\n", rc);
+	dev_err(&lp->spi->dev, "error: %d\n", rc);
 
 	spin_lock_irqsave(&lp->lock, flags);
 	lp->is_tx = 0;

@@ -732,7 +733,7 @@ static int at86rf230_rx(struct at86rf230_local *lp)
 
 	return 0;
 err:
-	pr_debug("received frame is too small\n");
+	dev_dbg(&lp->spi->dev, "received frame is too small\n");
 
 	kfree_skb(skb);
 	return -EINVAL;

@@ -23,6 +23,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
+#include <linux/irq.h>
 #include <linux/gpio.h>
 #include <linux/delay.h>
 #include <linux/mutex.h>

@@ -971,8 +972,7 @@ static int at86rf230_irq_polarity(struct at86rf230_local *lp, int pol)
 
 static int at86rf230_hw_init(struct at86rf230_local *lp)
 {
-	struct at86rf230_platform_data *pdata = lp->spi->dev.platform_data;
-	int rc, irq_pol;
+	int rc, irq_pol, irq_type;
 	u8 status;
 	u8 csma_seed[2];
 

@@ -984,8 +984,9 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
 	if (rc)
 		return rc;
 
+	irq_type = irq_get_trigger_type(lp->spi->irq);
 	/* configure irq polarity, defaults to high active */
-	if (pdata->irq_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
+	if (irq_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
 		irq_pol = IRQ_ACTIVE_LOW;
 	else
 		irq_pol = IRQ_ACTIVE_HIGH;

@@ -1041,7 +1042,6 @@ static struct at86rf230_platform_data *
 at86rf230_get_pdata(struct spi_device *spi)
 {
 	struct at86rf230_platform_data *pdata;
-	const char *irq_type;
 
 	if (!IS_ENABLED(CONFIG_OF) || !spi->dev.of_node)
 		return spi->dev.platform_data;

@@ -1053,19 +1053,6 @@ at86rf230_get_pdata(struct spi_device *spi)
 	pdata->rstn = of_get_named_gpio(spi->dev.of_node, "reset-gpio", 0);
 	pdata->slp_tr = of_get_named_gpio(spi->dev.of_node, "sleep-gpio", 0);
 
-	pdata->irq_type = IRQF_TRIGGER_RISING;
-	of_property_read_string(spi->dev.of_node, "irq-type", &irq_type);
-	if (!strcmp(irq_type, "level-high"))
-		pdata->irq_type = IRQF_TRIGGER_HIGH;
-	else if (!strcmp(irq_type, "level-low"))
-		pdata->irq_type = IRQF_TRIGGER_LOW;
-	else if (!strcmp(irq_type, "edge-rising"))
-		pdata->irq_type = IRQF_TRIGGER_RISING;
-	else if (!strcmp(irq_type, "edge-falling"))
-		pdata->irq_type = IRQF_TRIGGER_FALLING;
-	else
-		dev_warn(&spi->dev, "wrong irq-type specified using edge-rising\n");
-
 	spi->dev.platform_data = pdata;
 done:
 	return pdata;

@@ -1080,7 +1067,7 @@ static int at86rf230_probe(struct spi_device *spi)
 	u8 part = 0, version = 0, status;
 	irq_handler_t irq_handler;
 	work_func_t irq_worker;
-	int rc;
+	int rc, irq_type;
 	const char *chip;
 	struct ieee802154_ops *ops = NULL;
 

@@ -1185,7 +1172,8 @@ static int at86rf230_probe(struct spi_device *spi)
 	dev->extra_tx_headroom = 0;
 	dev->flags = IEEE802154_HW_OMIT_CKSUM | IEEE802154_HW_AACK;
 
-	if (pdata->irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
+	irq_type = irq_get_trigger_type(spi->irq);
+	if (irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
 		irq_worker = at86rf230_irqwork;
 		irq_handler = at86rf230_isr;
 	} else {

@@ -1212,7 +1200,7 @@ static int at86rf230_probe(struct spi_device *spi)
 		goto err_hw_init;
 
 	rc = request_irq(spi->irq, irq_handler,
-			 IRQF_SHARED | pdata->irq_type,
+			 IRQF_SHARED | irq_type,
 			 dev_name(&spi->dev), lp);
 	if (rc)
 		goto err_hw_init;

@@ -26,20 +26,6 @@ struct at86rf230_platform_data {
 	int rstn;
 	int slp_tr;
 	int dig2;
-
-	/* Setting the irq_type will configure the driver to request
-	 * the platform irq trigger type according to the given value
-	 * and configure the interrupt polarity of the device to the
-	 * corresponding polarity.
-	 *
-	 * Allowed values are: IRQF_TRIGGER_RISING, IRQF_TRIGGER_FALLING,
-	 *                     IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW
-	 *
-	 * Setting it to 0, the driver does not touch the trigger type
-	 * configuration of the interrupt and sets the interrupt polarity
-	 * of the device to high active (the default value).
-	 */
-	int irq_type;
 };
 
 #endif

@@ -0,0 +1,23 @@
+* AT86RF230 IEEE 802.15.4 *
+
+Required properties:
+  - compatible:		should be "atmel,at86rf230", "atmel,at86rf231",
+			"atmel,at86rf233" or "atmel,at86rf212"
+  - spi-max-frequency:	maximal bus speed, should be set to 7500000 depends
+			sync or async operation mode
+  - reg:		the chipselect index
+  - interrupts:		the interrupt generated by the device
+
+Optional properties:
+  - reset-gpio:		GPIO spec for the rstn pin
+  - sleep-gpio:		GPIO spec for the slp_tr pin
+
+Example:
+
+	at86rf231@0 {
+		compatible = "atmel,at86rf231";
+		spi-max-frequency = <7500000>;
+		reg = <0>;
+		interrupts = <19 1>;
+		interrupt-parent = <&gpio3>;
+	};