PROBLEM: BNX2 missing fw file
From: Marco Carlo Spada <hidden>
Date: 2012-12-09 10:57:57
Hi everybody, few days ago I installed and recompiled kernel release 3.6.9 on an HP Server ML350g5 with a bnx2 ethernet controller on board. I¹m using a Slackware64 V.13.37 distro. After booting up, I could not see the controller. From ³dmesg² log I noticed that bnx2 driver would load the firmware file called ³bnx2/bnx2-mips-06-6.2.3.fw², but this file is not present. I could download it from ³http://git2.kernel.org/?p=linux/kernel/git/firmware/linux-firmware.git;a=tr ee;f=bnx2;h=78c16645553a90b365391312546ca4e256f271fb;hb=654c70dae35817b6a5f6 dae553c5d4ef38d07195². ===== It seems to me that the dir contents of /usr/src/linux-3.6.9/firmware/bnx2 are not in sync with the /usr/src/linux-3.6.9/drivers/net/ethernet/broadcom/bnx2.c source file. If this can be of some help, I send you here some listings I produced during the debug analisys I did. Here are relevant lines from ³dmesg²... bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.2.3 (June 27, 2012) bnx2 0000:03:00.0: eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem fa000000, IRQ 16, node addr 00:23:7d:a0:48:c6 8139too: 8139too Fast Ethernet driver 0.9.28 8139too 0000:0c:02.0: eth1: RealTek RTL8139 at 0x0000000000014000, 00:0e:2e:85:f1:cb, IRQ 26 8139too 0000:0c:02.0: eth0: link down bnx2: Can't load firmware file "bnx2/bnx2-mips-06-6.2.3.fw" bnx2: Can't load firmware file "bnx2/bnx2-mips-06-6.2.3.fw" 8139too 0000:0c:02.0: eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 ..the listing of firmware lib dir and the listing of the kernel firmware object dir: root@srv-virt:~# ls -la /lib/firmware/bnx2 total 236 drwxr-xr-x 2 root root 4096 Apr 9 2011 ./ drwxr-xr-x 38 root root 4096 Mar 11 2011 ../ -rw-r--r-- 1 root root 92780 Apr 9 2011 bnx2-mips-06-6.0.15.fw -rw-r--r-- 1 root root 103488 Apr 9 2011 bnx2-mips-09-6.0.17.fw -rw-r--r-- 1 root root 5696 Apr 9 2011 bnx2-rv2p-06-6.0.15.fw -rw-r--r-- 1 root root 6104 Apr 9 2011 bnx2-rv2p-09-6.0.17.fw -rw-r--r-- 1 root root 6616 Apr 9 2011 bnx2-rv2p-09ax-6.0.17.fw root@srv-virt:~# ls -la /usr/src/linux/firmware/bnx2 total 1100 drwxrwxr-x 2 root root 4096 Dec 6 19:37 ./ drwxrwxr-x 37 root root 4096 Dec 6 19:39 ../ -rw-r--r-- 1 root root 853 Dec 6 19:37 .bnx2-mips-06-6.2.1.fw.gen.o.cmd -rw-r--r-- 1 root root 863 Dec 6 19:37 .bnx2-mips-09-6.2.1a.fw.gen.o.cmd -rw-r--r-- 1 root root 863 Dec 6 19:37 .bnx2-rv2p-06-6.0.15.fw.gen.o.cmd -rw-r--r-- 1 root root 863 Dec 6 19:37 .bnx2-rv2p-09-6.0.17.fw.gen.o.cmd -rw-r--r-- 1 root root 883 Dec 6 19:37 .bnx2-rv2p-09ax-6.0.17.fw.gen.o.cmd -rw-r--r-- 1 root root 92792 Dec 6 19:37 bnx2-mips-06-6.2.1.fw -rw-r--r-- 1 root root 503 Dec 6 19:37 bnx2-mips-06-6.2.1.fw.gen.S -rw-r--r-- 1 root root 94072 Dec 6 19:37 bnx2-mips-06-6.2.1.fw.gen.o -rw-rw-r-- 1 root root 255624 Dec 3 20:39 bnx2-mips-06-6.2.1.fw.ihex -rw-r--r-- 1 root root 103868 Dec 6 19:37 bnx2-mips-09-6.2.1a.fw -rw-r--r-- 1 root root 510 Dec 6 19:37 bnx2-mips-09-6.2.1a.fw.gen.S -rw-r--r-- 1 root root 105160 Dec 6 19:37 bnx2-mips-09-6.2.1a.fw.gen.o -rw-rw-r-- 1 root root 286104 Dec 3 20:39 bnx2-mips-09-6.2.1a.fw.ihex -rw-r--r-- 1 root root 5696 Dec 6 19:37 bnx2-rv2p-06-6.0.15.fw -rw-r--r-- 1 root root 510 Dec 6 19:37 bnx2-rv2p-06-6.0.15.fw.gen.S -rw-r--r-- 1 root root 6984 Dec 6 19:37 bnx2-rv2p-06-6.0.15.fw.gen.o -rw-rw-r-- 1 root root 16004 Dec 3 20:39 bnx2-rv2p-06-6.0.15.fw.ihex -rw-r--r-- 1 root root 6104 Dec 6 19:37 bnx2-rv2p-09-6.0.17.fw -rw-r--r-- 1 root root 510 Dec 6 19:37 bnx2-rv2p-09-6.0.17.fw.gen.S -rw-r--r-- 1 root root 7392 Dec 6 19:37 bnx2-rv2p-09-6.0.17.fw.gen.o -rw-rw-r-- 1 root root 17132 Dec 3 20:39 bnx2-rv2p-09-6.0.17.fw.ihex -rw-r--r-- 1 root root 6616 Dec 6 19:37 bnx2-rv2p-09ax-6.0.17.fw -rw-r--r-- 1 root root 524 Dec 6 19:37 bnx2-rv2p-09ax-6.0.17.fw.gen.S -rw-r--r-- 1 root root 7904 Dec 6 19:37 bnx2-rv2p-09ax-6.0.17.fw.gen.o -rw-rw-r-- 1 root root 18552 Dec 3 20:39 bnx2-rv2p-09ax-6.0.17.fw.ihex ... some lines from /usr/src/linux/firmware/Makefile ifdef CONFIG_ACENIC_OMIT_TIGON_I acenic-objs := acenic/tg2.bin fw-shipped- += acenic/tg1.bin else acenic-objs := acenic/tg1.bin acenic/tg2.bin endif fw-shipped-$(CONFIG_ACENIC) += $(acenic-objs) fw-shipped-$(CONFIG_ADAPTEC_STARFIRE) += adaptec/starfire_rx.bin \ adaptec/starfire_tx.bin fw-shipped-$(CONFIG_ATARI_DSP56K) += dsp56k/bootstrap.bin fw-shipped-$(CONFIG_ATM_AMBASSADOR) += atmsar11.fw fw-shipped-$(CONFIG_BNX2X) += bnx2x/bnx2x-e1-6.2.9.0.fw \ bnx2x/bnx2x-e1h-6.2.9.0.fw \ bnx2x/bnx2x-e2-6.2.9.0.fw fw-shipped-$(CONFIG_BNX2) += bnx2/bnx2-mips-09-6.2.1a.fw \ bnx2/bnx2-rv2p-09-6.0.17.fw \ bnx2/bnx2-rv2p-09ax-6.0.17.fw \ bnx2/bnx2-mips-06-6.2.1.fw \ bnx2/bnx2-rv2p-06-6.0.15.fw fw-shipped-$(CONFIG_CASSINI) += sun/cassini.bin the listing of /usr/src/linux-2.6.37.6/firmware/bnx2, the original distro kernel source dir root@srv-virt:/usr/src/linux-2.6.37.6/firmware/bnx2# ls -la total 604 drwxr-xr-x 2 root root 4096 Apr 9 2011 ./ drwxr-xr-x 37 root root 4096 Apr 9 2011 ../ -rw-r--r-- 1 root root 255564 Mar 27 2011 bnx2-mips-06-6.0.15.fw.ihex -rw-r--r-- 1 root root 285056 Mar 27 2011 bnx2-mips-09-6.0.17.fw.ihex -rw-r--r-- 1 root root 16004 Mar 27 2011 bnx2-rv2p-06-6.0.15.fw.ihex -rw-r--r-- 1 root root 17132 Mar 27 2011 bnx2-rv2p-09-6.0.17.fw.ihex -rw-r--r-- 1 root root 18552 Mar 27 2011 bnx2-rv2p-09ax-6.0.17.fw.ihex root@srv-virt:/usr/src/linux-2.6.37.6/firmware/bnx2# root@srv-virt:/usr/src/linux-2.6.37.6/firmware/bnx2# and last, a piece of code from /usr/src/linux-3.6.9/drivers/net/ethernet/broadcom/bnx2.c #include "bnx2.h" #include "bnx2_fw.h" #define DRV_MODULE_NAME "bnx2" #define DRV_MODULE_VERSION "2.2.3" #define DRV_MODULE_RELDATE "June 27, 2012" #define FW_MIPS_FILE_06 "bnx2/bnx2-mips-06-6.2.3.fw" #define FW_RV2P_FILE_06 "bnx2/bnx2-rv2p-06-6.0.15.fw" #define FW_MIPS_FILE_09 "bnx2/bnx2-mips-09-6.2.1b.fw" #define FW_RV2P_FILE_09_Ax "bnx2/bnx2-rv2p-09ax-6.0.17.fw" #define FW_RV2P_FILE_09 "bnx2/bnx2-rv2p-09-6.0.17.fw" #define RUN_AT(x) (jiffies + (x)) ======= I add here all other info from bug report guide I missed in my previous mail ... [1] BNX2 driver won¹t load [2] see above... [3] kernel driver net broadcom firmware [4] root@srv-virt:/usr/src/linux# cat /proc/version Linux version 3.6.9-built-on-20121206-by-mcs (root@srv-virt) (gcc version 4.5.2 (GCC) ) #1 SMP Thu Dec 6 19:39:20 CET 2012 root@srv-virt:/usr/src/linux# [5] n.a. [6] n.a. [7] [7.1] root@srv-virt:/usr/src/linux# sh scripts/ver_linux If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes. Linux srv-virt 3.6.9-built-on-20121206-by-mcs #1 SMP Thu Dec 6 19:39:20 CET 2012 x86_64 Intel(R) Xeon(R) CPU E5420 @ 2.50GHz GenuineIntel GNU/Linux Gnu C 4.5.2 Gnu make 3.82 binutils 2.21.51.0.6.20110118 util-linux 2.19 mount support module-init-tools 3.12 e2fsprogs 1.41.14 jfsutils 1.1.15 reiserfsprogs 3.6.21 xfsprogs 3.1.4 pcmciautils 017 quota-tools 3.17. PPP 2.4.5 Linux C Library 2.13 Dynamic linker (ldd) 2.13 Linux C++ Library 6.0.14 Procps 3.2.8 Net-tools 1.60 Kbd 1.15.2 oprofile 0.9.6 Sh-utils 8.11 Modules Loaded vboxpci vboxnetadp vboxnetflt vboxdrv root@srv-virt:/usr/src/linux# [7.2] root@srv-virt:/usr/src/linux# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5420 @ 2.50GHz stepping : 10 microcode : 0xa07 cpu MHz : 2499.864 cache size : 6144 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm dca sse4_1 xsave lahf_lm dtherm tpr_shadow vnmi flexpriority bogomips : 4999.72 clflush size : 64 cache_alignment : 64 address sizes : 38 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5420 @ 2.50GHz stepping : 10 microcode : 0xa07 cpu MHz : 2499.864 cache size : 6144 KB physical id : 0 siblings : 4 core id : 2 cpu cores : 4 apicid : 2 initial apicid : 2 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm dca sse4_1 xsave lahf_lm dtherm tpr_shadow vnmi flexpriority bogomips : 4999.72 clflush size : 64 cache_alignment : 64 address sizes : 38 bits physical, 48 bits virtual power management: processor : 2 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5420 @ 2.50GHz stepping : 10 microcode : 0xa07 cpu MHz : 2499.864 cache size : 6144 KB physical id : 0 siblings : 4 core id : 1 cpu cores : 4 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm dca sse4_1 xsave lahf_lm dtherm tpr_shadow vnmi flexpriority bogomips : 4999.72 clflush size : 64 cache_alignment : 64 address sizes : 38 bits physical, 48 bits virtual power management: processor : 3 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU E5420 @ 2.50GHz stepping : 10 microcode : 0xa07 cpu MHz : 2499.864 cache size : 6144 KB physical id : 0 siblings : 4 core id : 3 cpu cores : 4 apicid : 3 initial apicid : 3 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm dca sse4_1 xsave lahf_lm dtherm tpr_shadow vnmi flexpriority bogomips : 4999.72 clflush size : 64 cache_alignment : 64 address sizes : 38 bits physical, 48 bits virtual power management: root@srv-virt:/usr/src/linux# [7.3] root@srv-virt:/usr/src/linux# cat /proc/modules vboxpci 11528 0 - Live 0xffffffffa01db000 (O) vboxnetadp 17508 0 - Live 0xffffffffa01d3000 (O) vboxnetflt 14199 1 - Live 0xffffffffa01cb000 (O) vboxdrv 1787876 4 vboxpci,vboxnetadp,vboxnetflt, Live 0xffffffffa0000000 (O) root@srv-virt:/usr/src/linux# [7.4] root@srv-virt:/usr/src/linux# cat /proc/ioports 0000-0cf7 : PCI Bus 0000:00 0000-001f : dma1 0020-0021 : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-0060 : keyboard 0064-0064 : keyboard 0070-0071 : rtc_cmos 0070-0071 : rtc 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : 0000:00:1f.2 0170-0177 : ata_piix 01f0-01f7 : 0000:00:1f.2 01f0-01f7 : ata_piix 02f8-02ff : pnp 00:01 0376-0376 : 0000:00:1f.2 0376-0376 : ata_piix 03c0-03df : vga+ 03f6-03f6 : 0000:00:1f.2 03f6-03f6 : ata_piix 0408-040f : pnp 00:01 04d0-04d1 : pnp 00:01 0500-050f : 0000:00:1f.2 0500-050f : ata_piix 0700-071f : pnp 00:01 0800-083f : pnp 00:01 0900-097f : pnp 00:01 0900-0903 : ACPI PM1a_EVT_BLK 0904-0907 : ACPI PM1a_CNT_BLK 0908-090b : ACPI PM_TMR 0928-092f : ACPI GPE0_BLK 0950-0953 : ACPI PM2_CNT_BLK 0c80-0c83 : pnp 00:01 0ca0-0ca1 : pnp 00:01 0ca4-0ca5 : pnp 00:01 0cd4-0cd7 : pnp 00:01 0cf8-0cff : PCI conf1 0d00-ffff : PCI Bus 0000:00 0f50-0f58 : pnp 00:01 1000-101f : 0000:00:1d.0 1000-101f : uhci_hcd 1020-103f : 0000:00:1d.1 1020-103f : uhci_hcd 1040-105f : 0000:00:1d.2 1040-105f : uhci_hcd 1060-107f : 0000:00:1d.3 1060-107f : uhci_hcd 2000-3fff : PCI Bus 0000:01 2800-28ff : 0000:01:04.0 3000-30ff : 0000:01:03.0 3400-34ff : 0000:01:04.2 3800-381f : 0000:01:04.4 3800-381f : uhci_hcd 4000-4fff : PCI Bus 0000:04 4000-4fff : PCI Bus 0000:0c 4000-40ff : 0000:0c:02.0 4000-40ff : 8139too 5000-5fff : PCI Bus 0000:12 5000-5fff : PCI Bus 0000:13 5000-50ff : 0000:13:08.0 5000-50ff : cciss root@srv-virt:/usr/src/linux# root@srv-virt:/usr/src/linux# cat /proc/iomem 00000000-0000ffff : reserved 00010000-0009f3ff : System RAM 0009f400-0009ffff : reserved 000a0000-000bffff : PCI Bus 0000:00 000c0000-000cafff : Video ROM 000f0000-000fffff : reserved 000f0000-000fffff : System ROM 00100000-dfe53fff : System RAM 01000000-0143e071 : Kernel code 0143e072-016597ff : Kernel data 016de000-01741fff : Kernel bss dfe54000-dfe5bfff : ACPI Tables dfe5c000-dfe5cfff : System RAM dfe5d000-efffffff : reserved e0000000-efffffff : PCI MMCONFIG 0000 [bus 00-ff] e0000000-efffffff : pnp 00:01 f0000000-febfffff : PCI Bus 0000:00 f0000000-f7ffffff : PCI Bus 0000:01 f0000000-f7ffffff : 0000:01:03.0 f8000000-f80fffff : PCI Bus 0000:12 f8000000-f80fffff : PCI Bus 0000:13 f8000000-f8003fff : 0000:13:08.0 f8100000-f81fffff : PCI Bus 0000:02 f8100000-f81fffff : PCI Bus 0000:03 f8100000-f81007ff : 0000:03:00.0 f9df0000-f9df03ff : 0000:00:1d.7 f9df0000-f9df03ff : ehci_hcd f9e00000-f9ffffff : PCI Bus 0000:01 f9e00000-f9e1ffff : 0000:01:03.0 f9e20000-f9e2ffff : 0000:01:04.2 f9ef0000-f9ef00ff : 0000:01:04.6 f9f00000-f9f7ffff : 0000:01:04.2 f9fc0000-f9fc1fff : 0000:01:04.2 f9fd0000-f9fd07ff : 0000:01:04.2 f9fe0000-f9fe01ff : 0000:01:04.0 f9ff0000-f9ffffff : 0000:01:03.0 fa000000-fbffffff : PCI Bus 0000:02 fa000000-fbffffff : PCI Bus 0000:03 fa000000-fbffffff : 0000:03:00.0 fa000000-fbffffff : bnx2 fdd00000-fdefffff : PCI Bus 0000:04 fde00000-fdefffff : PCI Bus 0000:0c fdef0000-fdef00ff : 0000:0c:02.0 fdef0000-fdef00ff : 8139too fdf00000-fdffffff : PCI Bus 0000:12 fdf00000-fdffffff : PCI Bus 0000:13 fdf70000-fdf77fff : 0000:13:08.0 fdf70000-fdf77fff : cciss fdf80000-fdffffff : 0000:13:08.0 fdf80000-fdffffff : cciss fe000000-febfffff : pnp 00:01 fec00000-fecfffff : reserved fec00000-fec003ff : IOAPIC 0 fec80000-fec803ff : IOAPIC 1 fed00000-fed003ff : HPET 0 fee00000-fee0ffff : reserved fee00000-fee00fff : Local APIC ffc00000-ffffffff : reserved 100000000-11fffefff : System RAM 11ffff000-11fffffff : RAM buffer root@srv-virt:/usr/src/linux# [7.5] root@srv-virt:/usr/src/linux# lspci -vvv 00:00.0 Host bridge: Intel Corporation 5000Z Chipset Memory Controller Hub (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit- Address: fee00000 Data: 0000 Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 15, GenCap- CGenEn- ChkCap- ChkEn- 00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=0e, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: fdd00000-fdefffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit- Address: fee00000 Data: 0000 Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: pcieport 00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=17, subordinate=19, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit- Address: fee00000 Data: 0000 Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #3, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: pcieport 00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 4 (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0f, subordinate=11, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit- Address: fee00000 Data: 0000 Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #4, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: pcieport 00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 (rev b1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=12, subordinate=16, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit- Address: fee00000 Data: 0000 Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #5, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: pcieport 00:10.0 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:10.1 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:10.2 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:11.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:13.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:15.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:16.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1) Subsystem: Hewlett-Packard Company Device 31fd Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 09) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=03, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fa000000-fbffffff Prefetchable memory behind bridge: 00000000f8100000-00000000f81fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag+ RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Gammagraphx, Inc. (or missing ID) Device 0000 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed+ WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 Status: NegoPending- InProgress- Capabilities: [180 v1] Root Complex Link Desc: PortNumber=01 ComponentID=02 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed1c001 Kernel driver in use: pcieport 00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device 31fe Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at 1000 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device 31fe Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at 1020 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device 31fe Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 1040 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 (rev 09) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device 31fe Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at 1060 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 09) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device 31fe Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f9df0000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d9) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00002000-00003fff Memory behind bridge: f9e00000-f9ffffff Prefetchable memory behind bridge: 00000000f0000000-00000000f7ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: Hewlett-Packard Company Device 31fe 00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 09) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.2 IDE interface: Intel Corporation 631xESB/632xESB/3100 Chipset SATA IDE Controller (rev 09) (prog-if 80 [Master]) Subsystem: Compaq Computer Corporation Device 3201 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 0500 [size=16] Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ata_piix 01:03.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 31fb Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 7 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 3000 [size=256] Region 2: Memory at f9ff0000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at f9e00000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 01:04.0 System peripheral: Compaq Computer Corporation Integrated Lights Out Controller (rev 03) Subsystem: Hewlett-Packard Company Device 3305 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 2800 [size=256] Region 1: Memory at f9fe0000 (32-bit, non-prefetchable) [size=512] Capabilities: [f0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- 01:04.2 System peripheral: Compaq Computer Corporation Integrated Lights Out Processor (rev 03) Subsystem: Hewlett-Packard Company Device 3305 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 10 BIST result: 00 Region 0: I/O ports at 3400 [size=256] Region 1: Memory at f9fd0000 (32-bit, non-prefetchable) [size=2K] Region 2: Memory at f9fc0000 (32-bit, non-prefetchable) [size=8K] Region 3: Memory at f9f00000 (32-bit, non-prefetchable) [size=512K] [virtual] Expansion ROM at f9e20000 [disabled] [size=64K] Capabilities: [f0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- 01:04.4 USB Controller: Hewlett-Packard Company Proliant iLO2/iLO3 virtual USB controller (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device 3305 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin B routed to IRQ 22 Region 4: I/O ports at 3800 [size=32] Capabilities: [f0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 01:04.6 IPMI SMIC interface: Hewlett-Packard Company Proliant iLO2 virtual UART (prog-if 01) Subsystem: Hewlett-Packard Company Device 3305 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 5 Region 0: Memory at f9ef0000 (32-bit, non-prefetchable) [size=256] Capabilities: [f0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- 02:00.0 PCI bridge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=02, secondary=03, subordinate=03, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fa000000-fbffffff Prefetchable memory behind bridge: 00000000f8100000-00000000f81fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [60] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <4us, L1 <4us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=02:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=0 CommitmentLimit=0 Downstream: Capacity=0 CommitmentLimit=0 Capabilities: [b0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [14c v1] Power Budgeting <?> Capabilities: [160 v1] Device Serial Number 00-23-7d-ff-fe-a0-48-c6 03:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) Subsystem: Hewlett-Packard Company NC373i Integrated Multifunction Gigabit Server Adapter Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (16000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=32M] [virtual] Expansion ROM at f8100000 [disabled] [size=2K] Capabilities: [40] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=8 Status: Dev=03:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz- Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data Product Name: HP NC373i Multifunction Gigabit Server Adapter Read-only fields: [PN] Part number: N/A [EC] Engineering changes: N/A [SN] Serial number: 0123456789 [MN] Manufacture ID: 31 30 33 43 [RV] Reserved: checksum good, 37 byte(s) reserved End Capabilities: [58] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 4181 Kernel driver in use: bnx2 04:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=04, secondary=05, subordinate=0b, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Express (v1) Upstream Port, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr+ UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] Subsystem: Gammagraphx, Inc. (or missing ID) Device 0000 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: pcieport 04:00.3 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=04, secondary=0c, subordinate=0e, sec-latency=64 I/O behind bridge: 00004000-00004fff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry- MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr+ UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [6c] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] Subsystem: Gammagraphx, Inc. (or missing ID) Device 0000 Capabilities: [d8] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv Status: Dev=00:00.3 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=65535 CommitmentLimit=65535 Downstream: Capacity=65535 CommitmentLimit=65535 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- 05:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=05, secondary=06, subordinate=08, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain+ CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] Subsystem: Gammagraphx, Inc. (or missing ID) Device 0000 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: pcieport 05:01.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E2 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=05, secondary=09, subordinate=0b, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain+ CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] Subsystem: Gammagraphx, Inc. (or missing ID) Device 0000 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: pcieport 0c:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 26 Region 0: I/O ports at 4000 [size=256] Region 1: Memory at fdef0000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: 8139too 12:00.0 PCI bridge: Broadcom EPB PCI-Express to PCI-X Bridge (rev b4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=12, secondary=13, subordinate=16, sec-latency=64 I/O behind bridge: 00005000-00005fff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [60] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <16us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <4us, L1 <4us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=12:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=0 CommitmentLimit=0 Downstream: Capacity=0 CommitmentLimit=0 Capabilities: [b0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr- AERCap: First Error Pointer: 04, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [14c v1] Power Budgeting <?> 13:04.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge (rev b2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Bus: primary=13, secondary=14, subordinate=16, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv Status: Dev=13:04.0 64bit+ 133MHz+ SCD- USC- SCO- SRD- Upstream: Capacity=8 CommitmentLimit=8 Downstream: Capacity=8 CommitmentLimit=8 13:08.0 RAID bus controller: Hewlett-Packard Company Smart Array E200i (SAS Controller) Subsystem: Hewlett-Packard Company Smart Array E200i Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr+ DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx- Latency: 64 Interrupt: pin A routed to IRQ 19 Region 0: Memory at fdf80000 (64-bit, non-prefetchable) [size=512K] Region 2: I/O ports at 5000 [size=256] Region 3: Memory at fdf70000 (32-bit, non-prefetchable) [size=32K] [virtual] Expansion ROM at f8000000 [disabled] [size=16K] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [cc] MSI: Enable- Count=1/2 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [dc] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=1 Status: Dev=13:08.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=4096 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz- Kernel driver in use: cciss [7.6] root@srv-virt:/usr/src/linux# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HP Model: Ultrium 2-SCSI Rev: T61D Type: Sequential-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: DVD-RAM GH15L Rev: FA01 Type: CD-ROM ANSI SCSI revision: 05 [7.7] see above. best regards Marco Carlo Spada -- Divisione Sistemi - opiMAINT srl ing. Marco Carlo Spada (n° B034 Albo B O.d.I. PV) m.c.spada@opimaint.it Via Ludovico da Viadana, 7 - 20122 - Milano tel 02 58490336 fax 02 58307137