[RFT PATCH] 8139cp: properly support change of MTU values

Subsystems: networking drivers, the rest

STALE5014d

2 messages, 2 authors, 2012-12-01 · open the first message on its own page

[RFT PATCH] 8139cp: properly support change of MTU values

From: John Greene <hidden>
Date: 2012-11-30 20:53:31

The 8139cp driver has a change_mtu function that has not been
enabled since the dawn of the git repository. However, the
generic eth_change_mtu is not used in its place, so that
invalid MTU values can be set on the interface.

Original patch salvages the broken code for the single case of
setting the MTU while the interface is down, which is safe
and also includes the range check.  Now enhanced to support up
or down interface.

Original patch from
http://lkml.indiana.edu/hypermail/linux/kernel/1202.2/00770.html

Testing: has been test on virtual 8139cp setup without issue,
have no access real hardware 8139cp, need testing help.

Signed-off-by: "John Greene" <redacted>
CC: "David S. Miller" <davem@davemloft.net>
---
 drivers/net/ethernet/realtek/8139cp.c | 22 +++-------------------
 1 file changed, 3 insertions(+), 19 deletions(-)
diff --git a/drivers/net/ethernet/realtek/8139cp.c b/drivers/net/ethernet/realtek/8139cp.c
index 6cb96b4..7847c83 100644
--- a/drivers/net/ethernet/realtek/8139cp.c
+++ b/drivers/net/ethernet/realtek/8139cp.c
@@ -1226,12 +1226,9 @@ static void cp_tx_timeout(struct net_device *dev)
 	spin_unlock_irqrestore(&cp->lock, flags);
 }
 
-#ifdef BROKEN
 static int cp_change_mtu(struct net_device *dev, int new_mtu)
 {
 	struct cp_private *cp = netdev_priv(dev);
-	int rc;
-	unsigned long flags;
 
 	/* check for invalid MTU, according to hardware limits */
 	if (new_mtu < CP_MIN_MTU || new_mtu > CP_MAX_MTU)
@@ -1244,22 +1241,11 @@ static int cp_change_mtu(struct net_device *dev, int new_mtu)
 		return 0;
 	}
 
-	spin_lock_irqsave(&cp->lock, flags);
-
-	cp_stop_hw(cp);			/* stop h/w and free rings */
-	cp_clean_rings(cp);
-
+	/* network IS up, close it, reset MTU, and come up again. */
+	cp_close(dev);
 	dev->mtu = new_mtu;
-	cp_set_rxbufsize(cp);		/* set new rx buf size */
-
-	rc = cp_init_rings(cp);		/* realloc and restart h/w */
-	cp_start_hw(cp);
-
-	spin_unlock_irqrestore(&cp->lock, flags);
-
-	return rc;
+	return cp_open(dev);
 }
-#endif /* BROKEN */
 
 static const char mii_2_8139_map[8] = {
 	BasicModeCtrl,
@@ -1835,9 +1821,7 @@ static const struct net_device_ops cp_netdev_ops = {
 	.ndo_start_xmit		= cp_start_xmit,
 	.ndo_tx_timeout		= cp_tx_timeout,
 	.ndo_set_features	= cp_set_features,
-#ifdef BROKEN
 	.ndo_change_mtu		= cp_change_mtu,
-#endif
 
 #ifdef CONFIG_NET_POLL_CONTROLLER
 	.ndo_poll_controller	= cp_poll_controller,
-- 
1.7.11.7

Re: [RFT PATCH] 8139cp: properly support change of MTU values

From: Francois Romieu <romieu@fr.zoreil.com>
Date: 2012-12-01 22:13:50

John Greene [off-list ref] :
[...]
Testing: has been test on virtual 8139cp setup without issue,
have no access real hardware 8139cp, need testing help.
You should Cc: David Woodhouse [off-list ref] for testing.

[...]
quoted hunk
diff --git a/drivers/net/ethernet/realtek/8139cp.c b/drivers/net/ethernet/realtek/8139cp.c
index 6cb96b4..7847c83 100644
--- a/drivers/net/ethernet/realtek/8139cp.c
+++ b/drivers/net/ethernet/realtek/8139cp.c
[...]
quoted hunk
@@ -1244,22 +1241,11 @@ static int cp_change_mtu(struct net_device *dev, int new_mtu)
 		return 0;
 	}
 
-	spin_lock_irqsave(&cp->lock, flags);
-
-	cp_stop_hw(cp);			/* stop h/w and free rings */
-	cp_clean_rings(cp);
-
+	/* network IS up, close it, reset MTU, and come up again. */
+	cp_close(dev);
 	dev->mtu = new_mtu;
-	cp_set_rxbufsize(cp);		/* set new rx buf size */
-
-	rc = cp_init_rings(cp);		/* realloc and restart h/w */
-	cp_start_hw(cp);
-
-	spin_unlock_irqrestore(&cp->lock, flags);
-
-	return rc;
+	return cp_open(dev);
netif_running is true since cp_close() is not running from dev_close.
Bad things will happen if cp_open fails while cp_interrupt was waiting
for the lock.

-- 
Ueimor
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help