[PATCH] tc-tbf.8: Add parameter range to man page.

Signed-off-by: Li Wei <redacted>
---
 man/man8/tc-tbf.8 |    6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/man/man8/tc-tbf.8 b/man/man8/tc-tbf.8
index 3abb238..7b76146 100644
--- a/man/man8/tc-tbf.8
+++ b/man/man8/tc-tbf.8

@@ -76,6 +76,7 @@ latency parameter, which specifies the maximum amount of time a packet can
 sit in the TBF. The latter calculation takes into account the size of the
 bucket, the rate and possibly the peakrate (if set). These two parameters
 are mutually exclusive. 
+The range of parameter limit is [1, UINT32_MAX] bytes.
 .TP
 burst
 Also known as buffer or maxburst.

@@ -85,6 +86,7 @@ if you want to reach your configured rate!
 
 If your buffer is too small, packets may be dropped because more tokens arrive per timer tick than fit in your bucket.
 The minimum buffer size can be calculated by dividing the rate by HZ.
+The range of this parameter is [1, UINT32_MAX] bytes.
 
 Token usage calculations are performed using a table which by default has a resolution of 8 packets. 
 This resolution can be changed by specifying the 

@@ -96,11 +98,13 @@ this. Must be an integral power of 2.
 mpu
 A zero-sized packet does not use zero bandwidth. For ethernet, no packet uses less than 64 bytes. The Minimum Packet Unit 
 determines the minimal token usage (specified in bytes) for a packet. Defaults to zero.
+The range of this parameter is [0, UINT32_MAX] bytes.
 .TP
 rate
 The speed knob. See remarks above about limits! See 
 .BR tc (8)
 for units.
+The range of this parameter is [1, UINT32_MAX] bps.
 .PP
 Furthermore, if a peakrate is desired, the following parameters are available:
 

@@ -108,12 +112,14 @@ Furthermore, if a peakrate is desired, the following parameters are available:
 peakrate
 Maximum depletion rate of the bucket. Limited to 1mbit/s on Intel, 10mbit/s on Alpha. The peakrate does 
 not need to be set, it is only necessary if perfect millisecond timescale shaping is required.
+The range of this parameter is [1, UINT32_MAX] bps.
 
 .TP
 mtu/minburst
 Specifies the size of the peakrate bucket. For perfect accuracy, should be set to the MTU of the interface.
 If a peakrate is needed, but some burstiness is acceptable, this size can be raised. A 3000 byte minburst
 allows around 3mbit/s of peakrate, given 1000 byte packets.
+The range of this parameter is [1, UINT32_MAX] bytes.
 
 Like the regular burstsize you can also specify a 
 .B cell

-- 
1.7.10.1

On Tue, 7 Aug 2012 10:30:32 +0800
Li Wei [off-list ref] wrote:

Not sure about this, other qdisc don't document ranges on their man pages.
Probably better to fix the generic documentation about qdisc parameters
which already exists on 'tc-qdisc' man page.

On 08/13/2012 11:30 PM, Stephen Hemminger wrote:

On Tue, 7 Aug 2012 10:30:32 +0800
Li Wei [off-list ref] wrote:

quoted

Signed-off-by: Li Wei <redacted>
---
 man/man8/tc-tbf.8 |    6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/man/man8/tc-tbf.8 b/man/man8/tc-tbf.8
index 3abb238..7b76146 100644
--- a/man/man8/tc-tbf.8
+++ b/man/man8/tc-tbf.8

@@ -76,6 +76,7 @@ latency parameter, which specifies the maximum amount of time a packet can
 sit in the TBF. The latter calculation takes into account the size of the
 bucket, the rate and possibly the peakrate (if set). These two parameters
 are mutually exclusive. 
+The range of parameter limit is [1, UINT32_MAX] bytes.
 .TP
 burst
 Also known as buffer or maxburst.

@@ -85,6 +86,7 @@ if you want to reach your configured rate!
 
 If your buffer is too small, packets may be dropped because more tokens arrive per timer tick than fit in your bucket.
 The minimum buffer size can be calculated by dividing the rate by HZ.
+The range of this parameter is [1, UINT32_MAX] bytes.
 
 Token usage calculations are performed using a table which by default has a resolution of 8 packets. 
 This resolution can be changed by specifying the 

@@ -96,11 +98,13 @@ this. Must be an integral power of 2.
 mpu
 A zero-sized packet does not use zero bandwidth. For ethernet, no packet uses less than 64 bytes. The Minimum Packet Unit 
 determines the minimal token usage (specified in bytes) for a packet. Defaults to zero.
+The range of this parameter is [0, UINT32_MAX] bytes.
 .TP
 rate
 The speed knob. See remarks above about limits! See 
 .BR tc (8)
 for units.
+The range of this parameter is [1, UINT32_MAX] bps.
 .PP
 Furthermore, if a peakrate is desired, the following parameters are available:
 

@@ -108,12 +112,14 @@ Furthermore, if a peakrate is desired, the following parameters are available:
 peakrate
 Maximum depletion rate of the bucket. Limited to 1mbit/s on Intel, 10mbit/s on Alpha. The peakrate does 
 not need to be set, it is only necessary if perfect millisecond timescale shaping is required.
+The range of this parameter is [1, UINT32_MAX] bps.
 
 .TP
 mtu/minburst
 Specifies the size of the peakrate bucket. For perfect accuracy, should be set to the MTU of the interface.
 If a peakrate is needed, but some burstiness is acceptable, this size can be raised. A 3000 byte minburst
 allows around 3mbit/s of peakrate, given 1000 byte packets.
+The range of this parameter is [1, UINT32_MAX] bytes.
 
 Like the regular burstsize you can also specify a 
 .B cell

Not sure about this, other qdisc don't document ranges on their man pages.
Probably better to fix the generic documentation about qdisc parameters
which already exists on 'tc-qdisc' man page.

Hi Stephen,

Not very clear with "the generic documentation about qdisc parameters
which already exists on 'tc-qdisc' man page", is there a separate man page
that describe qdisc parameters?

I'm reading the iproute2 and kernel code which related to TC and record the
value range for each parameter, I think that would be helpful for somebody
else.

Thanks.

Not very clear with "the generic documentation about qdisc parameters
which already exists on 'tc-qdisc' man page", is there a separate man page
that describe qdisc parameters?

I'm reading the iproute2 and kernel code which related to TC and record the
value range for each parameter, I think that would be helpful for somebody
else.

Rather than putting range on each parameter on every sub-page of tc man
page. Why not put something in tc.8 under UNITS.

The following implies everything is floating-point which it isn't:

UNITS
       All parameters accept a floating point number, possibly followed  by  a
       unit.

I would like this section broken down to cover all the generic types
  PARAMETERS
     RATES
     TIMES
     SIZES
     VALUES

Also needs to explain IEC units here.

On 08/21/2012 01:58 AM, Stephen Hemminger wrote:

quoted

Not very clear with "the generic documentation about qdisc parameters
which already exists on 'tc-qdisc' man page", is there a separate man page
that describe qdisc parameters?

I'm reading the iproute2 and kernel code which related to TC and record the
value range for each parameter, I think that would be helpful for somebody
else.

Rather than putting range on each parameter on every sub-page of tc man
page. Why not put something in tc.8 under UNITS.

The following implies everything is floating-point which it isn't:

UNITS
       All parameters accept a floating point number, possibly followed  by  a
       unit.

I would like this section broken down to cover all the generic types
  PARAMETERS
     RATES
     TIMES
     SIZES
     VALUES

Also needs to explain IEC units here.

Thanks Stephen, I got it and will try to work it out.