[PATCH v4 0/7] ARM: davinci: add support for the am1808 based enbw_cmc board

this patchserie add support for the davinci am1808 based
enbw_cmc board.

changes for v2:
Post this patchserie now as v2, as reworked in the
comments I got for the RFC serie.

changes for v3:
- Interrupt Controller:
  - comment from Sergei Shtylyov:
    - rename compatible" prop to "ti,cp_intc"
    - cp_intc_init() is now also for the of case
      the name of the init function (it calls the
      "new" __cp_intc_init() function, which was
      the "old" cp_intc_init()). Through this
      rework the changes for OF is better visible.
      As the OF case uses the irq_domain rework from
      Grant Likely, maybe the none OF case can use
      this also, but this should be tested on a hw ...

changes for v4:
- Interrupt Controller:
  - split in two patches as Nori Sekhar suggested
    one for the irq_domain change
    one for DT support
  - add comment from Grant Likely for the DT part:
    remove if/else clause, not needed.
    Make use of DT runtime configurable
    The non OF case is not tested!
     
Got no comments to the following points, I noted in the
RFC series, so posting this patchseries with them:

- ARM: davinci: configure davinci aemif chipselects through OF
  not moved to mfd, as mentioned in this discussion:
  http://davinci-linux-open-source.1494791.n2.nabble.com/PATCH-arm-davinci-configure-davinci-aemif-chipselects-through-OF-td7059739.html
  instead use a phandle in the DTS, so drivers which
  uses the davinci aemif, can call davinci_aemif_setup_timing_of()

  This is just thought as an RFC ... The enbw_cmc board
  support not really need to setup this bus timings, as
  they are setup in U-Boot ... but I want to post this,
  as I think, it is a nice to have, and I am not really
  sure, if this has to be a MFD device (If so, all bus
  interfaces for other SoCs should be converted also to
  MFD devices) ... as an example how this can be used
  I add this to the davinci nand controller OF support
  patch, in this patchserie.

- ARM: davinci: mux: add OF support
  I want to get rid of the pin setup code in board code ...
  This patch introduces a davinci_cfg_reg_of() function,
  which davinci drivers can call, if they found a
  "pinmux-handle", so used in the following drivers in
  this patchserie:

  drivers/net/ethernet/ti/davinci_emac
  drivers/i2c/busses/i2c-davinci.c
  drivers/mtd/nand/davinci_nand.c

  This is removed for v4 serie, as Nori Sekhar suggested.

- post this board support with USB support, even though
  USB is only working with the 10 ms "workaround", posted here:
  http://comments.gmane.org/gmane.linux.usb.general/54505
  I see this issue also on the AM1808 TMDXEXP1808L evalboard.

  change for v4:
  The 10 ms delay is no longer needed, see discussion here:

  http://www.spinics.net/lists/linux-usb/msg64232.html

  shows the way to go ...

- MMC and USB are not using OF support yet, ideas how to port
  this are welcome. I need for USB and MMC board specific
  callbacks, how to solve this with OF support?

Signed-off-by: Heiko Schocher <redacted>
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org
Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org
Cc: linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: David Woodhouse <redacted>
Cc: Ben Dooks <redacted>
Cc: Wolfram Sang <redacted>
Cc: Sekhar Nori <redacted>
Cc: Kevin Hilman <redacted>
Cc: Wolfgang Denk <redacted>
Cc: Sergei Shtylyov <redacted>
Cc: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

Heiko Schocher (7):
  ARM: davinci, intc: Add irq domain support
  ARM: davinci, intc: Add OF support for TI interrupt controller
  ARM: davinci: configure davinci aemif chipselects through OF
  ARM: davinci: net: davinci_emac: add OF support
  ARM: davinci: i2c: add OF support
  ARM: mtd: nand: davinci: add OF support for davinci nand controller
  ARM: davinci: add support for the am1808 based enbw_cmc board

 .../devicetree/bindings/arm/davinci/aemif.txt      |  119 +++++++
 .../devicetree/bindings/arm/davinci/i2c.txt        |   31 ++
 .../devicetree/bindings/arm/davinci/intc.txt       |   27 ++
 .../devicetree/bindings/arm/davinci/nand.txt       |   72 ++++
 .../devicetree/bindings/net/davinci_emac.txt       |   41 +++
 arch/arm/boot/dts/enbw_cmc.dts                     |  172 +++++++++
 arch/arm/configs/enbw_cmc_defconfig                |  123 +++++++
 arch/arm/mach-davinci/Kconfig                      |    9 +
 arch/arm/mach-davinci/Makefile                     |    1 +
 arch/arm/mach-davinci/aemif.c                      |   86 +++++-
 arch/arm/mach-davinci/board-enbw-cmc.c             |  374 ++++++++++++++++++++
 arch/arm/mach-davinci/cp_intc.c                    |   74 ++++-
 arch/arm/mach-davinci/include/mach/aemif.h         |    1 +
 arch/arm/mach-davinci/include/mach/uncompress.h    |    1 +
 drivers/i2c/busses/i2c-davinci.c                   |   32 ++
 drivers/mtd/nand/davinci_nand.c                    |   80 ++++-
 drivers/net/ethernet/ti/davinci_emac.c             |   87 +++++-
 17 files changed, 1317 insertions(+), 13 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/aemif.txt
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/i2c.txt
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/intc.txt
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/nand.txt
 create mode 100644 Documentation/devicetree/bindings/net/davinci_emac.txt
 create mode 100644 arch/arm/boot/dts/enbw_cmc.dts
 create mode 100644 arch/arm/configs/enbw_cmc_defconfig
 create mode 100644 arch/arm/mach-davinci/board-enbw-cmc.c

-- 
1.7.7.6

add of support for the davinci_emac driver.

Signed-off-by: Heiko Schocher <redacted>
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Cc: Grant Likely <redacted>
Cc: Sekhar Nori <redacted>
Cc: Wolfgang Denk <redacted>
Cc: Anatoly Sivov <redacted>

---
- changes for v2:
  - add comment from Anatoly Sivov
    - fix typo in davinci_emac.txt
  - add comment from Grant Likely:
    - add prefix "ti,davinci-" to davinci specific property names
    - remove version property
    - use compatible name "ti,davinci-dm6460-emac"
    - use devm_kzalloc()
    - use of_match_ptr()
    - document all new properties
    - remove of_address_to_resource() and do not overwrite
      resource table
    - whitespace fixes
    - remove hw_ram_addr as it is not used in current
      board code
- no changes for v3
- changes for v4:
  add comments from Nori Sekhar:
  - move devictree documentation to:
    Documentation/devicetree/bindings/net/davinci_emac.txt
  - fix typo in it
  - rename compatible property to "ti,davinci-dm6467-emac"
  - remove pinmux-handle
  - set version directly in pdata->version
---
 .../devicetree/bindings/net/davinci_emac.txt       |   41 +++++++++
 drivers/net/ethernet/ti/davinci_emac.c             |   87 +++++++++++++++++++-
 2 files changed, 127 insertions(+), 1 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/davinci_emac.txt

diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt
new file mode 100644
index 0000000..48b259e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/davinci_emac.txt

@@ -0,0 +1,41 @@
+* Texas Instruments Davinci EMAC
+
+This file provides information, what the device node
+for the davinci_emac interface contains.
+
+Required properties:
+- compatible: "ti,davinci-dm6467-emac";
+- reg: Offset and length of the register set for the device
+- ti,davinci-ctrl-reg-offset: offset to control register
+- ti,davinci-ctrl-mod-reg-offset: offset to control module register
+- ti,davinci-ctrl-ram-offset: offset to control module ram
+- ti,davinci-ctrl-ram-size: size of control module ram
+- ti,davinci-rmii-en: use RMII
+- ti,davinci-no-bd-ram: has the emac controller BD RAM
+- phy-handle: Contains a phandle to an Ethernet PHY.
+              if not, davinci_emac driver defaults to 100/FULL
+- interrupts: interrupt mapping for the davinci emac interrupts sources:
+              4 sources: <Receive Threshold Interrupt
+			  Receive Interrupt
+			  Transmit Interrupt
+			  Miscellaneous Interrupt>
+
+Optional properties:
+- local-mac-address : 6 bytes, mac address
+
+Example (enbw_cmc board):
+	eth0: emac@1e20000 {
+		compatible = "ti,davinci-dm6467-emac";
+		reg = <0x220000 0x4000>;
+		ti,davinci-ctrl-reg-offset = <0x3000>;
+		ti,davinci-ctrl-mod-reg-offset = <0x2000>;
+		ti,davinci-ctrl-ram-offset = <0>;
+		ti,davinci-ctrl-ram-size = <0x2000>;
+		local-mac-address = [ 00 00 00 00 00 00 ];
+		interrupts = <33
+				34
+				35
+				36
+				>;
+		interrupt-parent = <&intc>;
+	};

diff --git a/drivers/net/ethernet/ti/davinci_emac.c b/drivers/net/ethernet/ti/davinci_emac.c
index 4da93a5..645618d 100644
--- a/drivers/net/ethernet/ti/davinci_emac.c
+++ b/drivers/net/ethernet/ti/davinci_emac.c

@@ -58,6 +58,12 @@
 #include <linux/io.h>
 #include <linux/uaccess.h>
 #include <linux/davinci_emac.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_net.h>
+
+#include <mach/mux.h>
 
 #include <asm/irq.h>
 #include <asm/page.h>

@@ -339,6 +345,9 @@ struct emac_priv {
 	u32 rx_addr_type;
 	atomic_t cur_tx;
 	const char *phy_id;
+#ifdef CONFIG_OF
+	struct device_node *phy_node;
+#endif
 	struct phy_device *phydev;
 	spinlock_t lock;
 	/*platform specific members*/

@@ -1762,6 +1771,75 @@ static const struct net_device_ops emac_netdev_ops = {
 #endif
 };
 
+#ifdef CONFIG_OF
+static struct emac_platform_data
+	*davinci_emac_of_get_pdata(struct platform_device *pdev,
+	struct emac_priv *priv)
+{
+	struct device_node *np;
+	struct emac_platform_data *pdata = NULL;
+	const u8 *mac_addr;
+	u32 data;
+	int ret;
+
+	pdata = pdev->dev.platform_data;
+	if (!pdata) {
+		pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+		if (!pdata)
+			goto nodata;
+	}
+
+	np = pdev->dev.of_node;
+	if (!np)
+		goto nodata;
+	else
+		pdata->version = EMAC_VERSION_2;
+
+	mac_addr = of_get_mac_address(np);
+	if (mac_addr)
+		memcpy(pdata->mac_addr, mac_addr, ETH_ALEN);
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-reg-offset", &data);
+	if (!ret)
+		pdata->ctrl_reg_offset = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-mod-reg-offset",
+		&data);
+	if (!ret)
+		pdata->ctrl_mod_reg_offset = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-ram-offset", &data);
+	if (!ret)
+		pdata->ctrl_ram_offset = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-ram-size", &data);
+	if (!ret)
+		pdata->ctrl_ram_size = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-rmii-en", &data);
+	if (!ret)
+		pdata->rmii_en = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-no-bd-ram", &data);
+	if (!ret)
+		pdata->no_bd_ram = data;
+
+	priv->phy_node = of_parse_phandle(np, "phy-handle", 0);
+	if (!priv->phy_node)
+		pdata->phy_id = "";
+
+	pdev->dev.platform_data = pdata;
+nodata:
+	return  pdata;
+}
+#else
+static struct emac_platform_data
+	*davinci_emac_of_get_pdata(struct platform_device *pdev,
+	struct emac_priv *priv)
+{
+	return  pdev->dev.platform_data;
+}
+#endif
 /**
  * davinci_emac_probe: EMAC device probe
  * @pdev: The DaVinci EMAC device that we are removing

@@ -1804,7 +1882,7 @@ static int __devinit davinci_emac_probe(struct platform_device *pdev)
 
 	spin_lock_init(&priv->lock);
 
-	pdata = pdev->dev.platform_data;
+	pdata = davinci_emac_of_get_pdata(pdev, priv);
 	if (!pdata) {
 		dev_err(&pdev->dev, "no platform data\n");
 		rc = -ENODEV;

@@ -2015,6 +2093,12 @@ static const struct dev_pm_ops davinci_emac_pm_ops = {
 	.resume		= davinci_emac_resume,
 };
 
+static const struct of_device_id davinci_emac_of_match[] = {
+	{.compatible = "ti,davinci-dm6467-emac", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, davinci_emac_of_match);
+
 /**
  * davinci_emac_driver: EMAC platform driver structure
  */

@@ -2023,6 +2107,7 @@ static struct platform_driver davinci_emac_driver = {
 		.name	 = "davinci_emac",
 		.owner	 = THIS_MODULE,
 		.pm	 = &davinci_emac_pm_ops,
+		.of_match_table = of_match_ptr(davinci_emac_of_match),
 	},
 	.probe = davinci_emac_probe,
 	.remove = __devexit_p(davinci_emac_remove),

-- 
1.7.7.6