Just tried 3.3-rc3+git and 3.3-rc4 on a generic i815+P3+e100 PC. It
crashes consistently during the end of bootup, getning oops in
__neigh_for_each_release during timer softirq. 3.2 works fine.
[ 0.000000] Linux version 3.3.0-rc4 (mroos@rhn) (gcc version 4.6.2 (Debian 4.6.2-14) ) #16 PREEMPT Mon Feb 20 14:17:04 EET 2012
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000fec0000 (usable)
[ 0.000000] BIOS-e820: 000000000fec0000 - 000000000fef8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000fef8000 - 000000000ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI 2.3 present.
[ 0.000000] last_pfn = 0xfec0 max_arch_pfn = 0x100000
[ 0.000000] PAT not supported by CPU.
[ 0.000000] total RAM covered: 255M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 2M num_reg: 2 lose cover RAM: 0G
[ 0.000000] init_memory_mapping: 0000000000000000-000000000fec0000
[ 0.000000] ACPI: RSDP 000ff980 00014 (v00 AMI )
[ 0.000000] ACPI: RSDT 0fef0000 0002C (v01 D815EA D815EEA2 20021106 MSFT 00001011)
[ 0.000000] ACPI: FACP 0fef1000 00074 (v01 D815EA EA81510A 20021106 MSFT 00001011)
[ 0.000000] ACPI: DSDT 0fee0000 030E4 (v01 D815E2 EA81520A 00000023 MSFT 0100000B)
[ 0.000000] ACPI: FACS 0fef8000 00040
[ 0.000000] ACPI: SSDT 0fee30e4 00035 (v01 D815EA EA81510A 00000015 MSFT 0100000B)
[ 0.000000] 254MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0fec0000
[ 0.000000] low ram: 0 - 0fec0000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0000fec0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0000fec0
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] Found and enabled local APIC!
[ 0.000000] Allocating PCI resources starting at ff00000 (gap: ff00000:efc80000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64593
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.3.0-rc4 root=/dev/sda1 ro lapic netconsole=1980@192.168.74.17/eth0,1975@192.168.74.24/00:50:8d:91:d9:f0
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Memory: 253772k/260864k available (2381k kernel code, 6640k reserved, 1365k data, 284k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffe3000 - 0xfffff000 ( 112 kB)
[ 0.000000] vmalloc : 0xd06c0000 - 0xfffe1000 ( 761 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcfec0000 ( 254 MB)
[ 0.000000] .init : 0xc13a9000 - 0xc13f0000 ( 284 kB)
[ 0.000000] .data : 0xc1253600 - 0xc13a8d20 (1365 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1253600 (2381 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 930.270 MHz processor.
[ 0.008004] Calibrating delay loop (skipped), value calculated using timer frequency.. 1860.54 BogoMIPS (lpj=3721080)
[ 0.008208] pid_max: default: 32768 minimum: 301
[ 0.008426] Mount-cache hash table entries: 512
[ 0.008800] mce: CPU supports 5 MCE banks
[ 0.008931] CPU: Intel Pentium III (Coppermine) stepping 06
[ 0.009089] ACPI: Core revision 20120111
[ 0.014061] ACPI: setting ELCR to 0200 (from 0e00)
[ 0.015242] Performance Events: p6 PMU driver.
[ 0.015358] ... version: 0
[ 0.015450] ... bit width: 32
[ 0.015543] ... generic registers: 2
[ 0.015635] ... value mask: 00000000ffffffff
[ 0.015731] ... max period: 000000007fffffff
[ 0.015828] ... fixed-purpose events: 0
[ 0.015921] ... event mask: 0000000000000003
[ 0.016210] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.020001] NET: Registered protocol family 16
[ 0.020001] ACPI: bus type pci registered
[ 0.020001] PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=1
[ 0.020001] PCI: Using configuration type 1 for base access
[ 0.025178] bio: create slab <bio-0> at 0
[ 0.025598] ACPI: Added _OSI(Module Device)
[ 0.025700] ACPI: Added _OSI(Processor Device)
[ 0.025801] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.025901] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.029021] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.035893] ACPI: Interpreter enabled
[ 0.036019] ACPI: (supports S0 S5)
[ 0.036150] ACPI: Using PIC for interrupt routing
[ 0.040239] ACPI: Power Resource [FDDP] (off)
[ 0.041042] ACPI: Power Resource [URP1] (off)
[ 0.041866] ACPI: Power Resource [URP2] (off)
[ 0.042263] ACPI: Power Resource [LPTP] (off)
[ 0.047848] ACPI: No dock devices found.
[ 0.047978] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.048729] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.049988] PCI host bridge to bus 0000:00
[ 0.050089] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.050189] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.051366] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.052417] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.056124] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
[ 0.056466] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12)
[ 0.056792] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.057213] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12)
[ 0.057534] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12)
[ 0.057859] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.058280] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.058700] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12)
[ 0.059320] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.059516] vgaarb: loaded
[ 0.059610] vgaarb: bridge control possible 0000:00:02.0
[ 0.060247] SCSI subsystem initialized
[ 0.061156] PCI: Using ACPI for IRQ routing
[ 0.062055] pnp: PnP ACPI init
[ 0.062176] ACPI: bus type pnp registered
[ 0.069500] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.069620] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.069729] system 00:0c: [mem 0x00100000-0x0fefffff] could not be reserved
[ 0.069863] pnp: PnP ACPI: found 13 devices
[ 0.069963] ACPI: ACPI bus type pnp unregistered
[ 0.111918] Switching to clocksource acpi_pm
[ 0.112079] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[ 0.112185] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
[ 0.112296] pci 0000:00:1e.0: bridge window [mem 0xff800000-0xff8fffff]
[ 0.112405] pci 0000:00:1e.0: bridge window [mem 0xf6a00000-0xf6afffff pref]
[ 0.112807] NET: Registered protocol family 2
[ 0.113046] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.113392] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.113707] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.113911] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.114014] TCP reno registered
[ 0.114113] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.114226] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.114498] NET: Registered protocol family 1
[ 0.114737] pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.117097] VFS: Disk quotas dquot_6.5.2
[ 0.117248] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.117552] msgmni has been set to 495
[ 0.118165] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.118358] io scheduler noop registered
[ 0.118481] io scheduler cfq registered (default)
[ 0.119025] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.392083] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.668081] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.690295] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.710933] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.711547] Non-volatile memory driver v1.3
[ 0.711654] Linux agpgart interface v0.103
[ 0.711795] agpgart-intel 0000:00:00.0: Intel i815 Chipset
[ 0.711941] agpgart-intel 0000:00:00.0: detected gtt size: 65536K total, 65536K mappable
[ 0.712863] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 0.713087] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[ 0.713272] Hangcheck: Using getrawmonotonic().
[ 0.713478] [drm] Initialized drm 1.1.0 20060810
[ 0.713833] Floppy drive(s): fd0 is 1.44M
[ 0.731413] FDC 0 is a post-1991 82077
[ 0.734129] scsi0 : ata_piix
[ 0.734521] scsi1 : ata_piix
[ 0.737239] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.737358] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.737993] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 0.738097] e100: Copyright(c) 1999-2006 Intel Corporation
[ 0.738511] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[ 0.761695] e100 0000:01:08.0: eth0: addr 0xff86f000, irq 11, MAC addr 00:03:47:a4:64:d5
[ 0.762240] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.765652] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.765844] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.766395] mousedev: PS/2 mouse device common for all mice
[ 0.766827] rtc_cmos 00:02: RTC can wake from S4
[ 0.767132] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.767265] rtc0: alarms up to one month, 114 bytes nvram
[ 0.767456] cpuidle: using governor ladder
[ 0.767554] cpuidle: using governor menu
[ 0.769063] TCP cubic registered
[ 0.771339] NET: Registered protocol family 17
[ 0.771470] Registering the dns_resolver key type
[ 0.771600] Using IPI Shortcut mode
[ 0.772140] netconsole: local port 1980
[ 0.772244] netconsole: local IP 192.168.74.17
[ 0.772343] netconsole: interface 'eth0'
[ 0.772439] netconsole: remote port 1975
[ 0.772536] netconsole: remote IP 192.168.74.24
[ 0.772636] netconsole: remote ethernet address 00:50:8d:91:d9:f0
[ 0.772787] netconsole: device eth0 not up yet, forcing it
[ 0.789721] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.792173] e100 0000:01:08.0: eth0: NIC Link is Up 100 Mbps Full Duplex
[ 0.796023] netconsole: carrier detect appears untrustworthy, waiting 4 seconds
[ 0.956500] ata1.00: ATA-6: ST380011A, 8.01, max UDMA/100
[ 0.956605] ata1.00: 156301488 sectors, multi 16: LBA48
[ 0.972370] ata1.00: configured for UDMA/100
[ 0.972800] scsi 0:0:0:0: Direct-Access ATA ST380011A 8.01 PQ: 0 ANSI: 5
[ 0.973638] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 0.973964] sd 0:0:0:0: [sda] Write Protect is off
[ 0.974129] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.995686] sda: sda1 sda2 sda3
[ 0.996805] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.112032] Refined TSC clocksource calibration: 930.314 MHz.
[ 1.112149] Switching to clocksource tsc
[ 4.801225] console [netcon0] enabled
[ 4.801357] netconsole: network logging started
[ 4.801532] rtc_cmos 00:02: setting system clock to 2012-02-20 12:55:15 UTC (1329742515)
[ 4.817157] EXT3-fs (sda1): recovery required on readonly filesystem
[ 4.817290] EXT3-fs (sda1): write access will be enabled during recovery
[ 5.283547] kjournald starting. Commit interval 5 seconds
[ 5.283909] EXT3-fs (sda1): recovery complete
[ 5.284026] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 5.284171] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[ 5.284359] Freeing unused kernel memory: 284k freed
[ 5.285311] Write protecting the kernel text: 2384k
[ 5.285522] Write protecting the kernel read-only data: 1196k
[ 7.550607] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 7.550827] ACPI: Power Button [PBTN]
[ 7.551139] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 7.551322] ACPI: Power Button [PWRF]
[ 7.659948] parport_pc 00:0a: reported by Plug and Play ACPI
[ 7.660246] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 7.989627] usbcore: registered new interface driver usbfs
[ 7.990381] usbcore: registered new interface driver hub
[ 7.991881] usbcore: registered new device driver usb
[ 8.062219] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.140339] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
[ 8.148670] uhci_hcd: USB Universal Host Controller Interface driver
[ 8.149220] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 8.149363] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 8.149481] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[ 8.149716] uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000ef40
[ 8.149910] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.150031] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.150223] usb usb1: Product: UHCI Host Controller
[ 8.150325] usb usb1: Manufacturer: Linux 3.3.0-rc4 uhci_hcd
[ 8.150434] usb usb1: SerialNumber: 0000:00:1f.2
[ 8.150793] hub 1-0:1.0: USB hub found
[ 8.150908] hub 1-0:1.0: 2 ports detected
[ 8.151363] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[ 8.151504] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[ 8.151622] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
[ 8.151858] uhci_hcd 0000:00:1f.4: irq 10, io base 0x0000ef80
[ 8.159500] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.159644] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.159874] usb usb2: Product: UHCI Host Controller
[ 8.159978] usb usb2: Manufacturer: Linux 3.3.0-rc4 uhci_hcd
[ 8.160141] usb usb2: SerialNumber: 0000:00:1f.4
[ 8.165932] hub 2-0:1.0: USB hub found
[ 8.166086] hub 2-0:1.0: 2 ports detected
[ 9.396043] intel8x0_measure_ac97_clock: measured 52271 usecs (2926 samples)
[ 9.396191] intel8x0: clocking to 41159
[ 10.231275] Adding 1048572k swap on /dev/sda2. Priority:-1 extents:1 across:1048572k
[ 10.476088] EXT3-fs (sda1): using internal journal
[ 10.595095] NTFS driver 2.1.30 [Flags: R/W MODULE].
[ 10.824763] usbcore: registered new interface driver libusual
[ 10.830985] Initializing USB Mass Storage driver...
[ 10.832120] usbcore: registered new interface driver usb-storage
[ 10.832255] USB Mass Storage support registered.
[ 10.885221] smsc47m1: Found SMSC LPC47M10x/LPC47M112/LPC47M13x
[ 10.885384] ACPI Warning: 0x00000804-0x00000804 SystemIO conflicts with Region \_SB_.PCI0.SBRG.RNT3 1 (20120111/utaddress-251)
[ 10.885622] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.766616] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 13.138202] NET: Registered protocol family 8
[ 13.138341] NET: Registered protocol family 20
[ 15.402941] NET: Registered protocol family 10
[ 17.837703] RPC: Registered named UNIX socket transport module.
[ 17.837917] RPC: Registered udp transport module.
[ 17.838021] RPC: Registered tcp transport module.
[ 17.838125] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 17.938275] Registering the id_resolver key type
[ 17.969638] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 18.725603] fuse init (API version 7.18)
[ 20.391759] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input3
[ 20.915381] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 20.928931] NFSD: starting 90-second grace period
[ 23.179451] lp0: using parport0 (interrupt-driven).
[ 23.192176] ppdev: user-space parallel port driver
[ 23.264048] BUG: unable to handle kernel NULL pointer dereference at 00000004
[ 23.264241] IP: [<c11e4cfa>] __neigh_for_each_release+0x7c/0x92
[ 23.264385] *pde = 00000000
[ 23.264493] Oops: 0000 [#1] PREEMPT
[ 23.264616] Modules linked in: ppdev lp uinput fuse nfsd nfs lockd auth_rpcgss nfs_acl sunrpc ipv6 clip atm ext4 jbd2 adm1025 hwmon_vid hwmon usb_storage usb_libusual udf crc_itu_t isofs zlib_inflate vfat fat eeprom ntfs snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device snd uhci_hcd i2c_i801 ehci_hcd evdev serio_raw usbcore usb_common soundcore snd_page_alloc parport_pc parport button processor
[ 23.265997]
[ 23.266098] Pid: 0, comm: swapper Not tainted 3.3.0-rc4 #16 /D815EEA2
[ 23.266330] EIP: 0060:[<c11e4cfa>] EFLAGS: 00010286 CPU: 0
[ 23.266438] EIP is at __neigh_for_each_release+0x7c/0x92
[ 23.266544] EAX: d08f036c EBX: 00000000 ECX: 00000000 EDX: d08edf38
[ 23.266655] ESI: 00000000 EDI: d08ede2b EBP: cf809f78 ESP: cf809f60
[ 23.266766] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[ 23.266875] Process swapper (pid: 0, ti=cf808000 task=c1388460 task.ti=c1380000)
[ 23.267065] Stack:
[ 23.267163] cf97d8a0 cf97d8a0 d08edf38 00000100 c141bc80 d08ede2b cf809f80 d08ede47
[ 23.267455] cf809fc4 c1022309 cf809fac c118a00d cf809fac c1030e0e cd5dc390 00000001
[ 23.267756] c141c68c c141c48c 00000000 cf809fb0 cf809fb0 cf809fb0 c141bb5c 00000001
[ 23.268004] Call Trace:
[ 23.268004] [<d08edf38>] ? clip_seq_show+0x3b/0x3b [clip]
[ 23.268004] [<d08ede2b>] ? clip_seq_start+0x21/0x21 [clip]
[ 23.268004] [<d08ede47>] idle_timer_check+0x1c/0x4a [clip]
[ 23.268004] [<c1022309>] run_timer_softirq+0x140/0x1de
[ 23.268004] [<c118a00d>] ? scsi_softirq_done+0xbf/0xc7
[ 23.268004] [<c1030e0e>] ? put_cred_rcu+0x6f/0x76
[ 23.268004] [<c101e24a>] __do_softirq+0x5f/0xe8
[ 23.268004] [<c101e1eb>] ? send_remote_softirq+0x18/0x18
[ 23.268004] <IRQ>
[ 23.268004] [<c101e44b>] ? irq_exit+0x34/0x8b
[ 23.268004] [<c1012644>] ? smp_apic_timer_interrupt+0x6e/0x79
[ 23.268004] [<c125225d>] ? apic_timer_interrupt+0x31/0x38
[ 23.268004] [<c1006f7e>] ? default_idle+0x29/0x3e
[ 23.268004] [<c1001574>] ? cpu_idle+0x73/0xa6
[ 23.268004] [<c1243453>] ? rest_init+0x77/0x79
[ 23.268004] [<c13a9653>] ? start_kernel+0x296/0x29c
[ 23.268004] [<c13a91ca>] ? obsolete_checksetup+0x8b/0x8b
[ 23.268004] [<c13a9044>] ? i386_start_kernel+0x44/0x46
[ 23.268004] Code: 14 8b 52 08 f6 c2 08 74 0b 89 45 e8 e8 31 ca 06 00 8b 45 e8 85 c0 74 07 89 f8 e8 5c ff ff ff 8b 3b 85 ff 75 b2 89 f3 8b 75 ec 43 <8b> 4e 04 b8 01 00 00 00 d3 e0 39 c3 7c 8c 83 c4 0c 5b 5e 5f 5d
[ 23.268004] EIP: [<c11e4cfa>] __neigh_for_each_release+0x7c/0x92 SS:ESP 0068:cf809f60
[ 23.268004] CR2: 0000000000000004
[ 23.271899] ---[ end trace f4b1cbf2fb401c6c ]---
[ 23.272011] Kernel panic - not syncing: Fatal exception in interrupt
--
Meelis Roos (mroos@linux.ee)
Le lundi 20 février 2012 à 14:02 +0200, Meelis Roos a écrit :
Just tried 3.3-rc3+git and 3.3-rc4 on a generic i815+P3+e100 PC. It
crashes consistently during the end of bootup, getning oops in
__neigh_for_each_release during timer softirq. 3.2 works fine.
[ 0.000000] Linux version 3.3.0-rc4 (mroos@rhn) (gcc version 4.6.2 (Debian 4.6.2-14) ) #16 PREEMPT Mon Feb 20 14:17:04 EET 2012
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000fec0000 (usable)
[ 0.000000] BIOS-e820: 000000000fec0000 - 000000000fef8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000fef8000 - 000000000ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI 2.3 present.
[ 0.000000] last_pfn = 0xfec0 max_arch_pfn = 0x100000
[ 0.000000] PAT not supported by CPU.
[ 0.000000] total RAM covered: 255M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 2M num_reg: 2 lose cover RAM: 0G
[ 0.000000] init_memory_mapping: 0000000000000000-000000000fec0000
[ 0.000000] ACPI: RSDP 000ff980 00014 (v00 AMI )
[ 0.000000] ACPI: RSDT 0fef0000 0002C (v01 D815EA D815EEA2 20021106 MSFT 00001011)
[ 0.000000] ACPI: FACP 0fef1000 00074 (v01 D815EA EA81510A 20021106 MSFT 00001011)
[ 0.000000] ACPI: DSDT 0fee0000 030E4 (v01 D815E2 EA81520A 00000023 MSFT 0100000B)
[ 0.000000] ACPI: FACS 0fef8000 00040
[ 0.000000] ACPI: SSDT 0fee30e4 00035 (v01 D815EA EA81510A 00000015 MSFT 0100000B)
[ 0.000000] 254MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0fec0000
[ 0.000000] low ram: 0 - 0fec0000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0000fec0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0000fec0
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] Found and enabled local APIC!
[ 0.000000] Allocating PCI resources starting at ff00000 (gap: ff00000:efc80000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64593
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.3.0-rc4 root=/dev/sda1 ro lapic netconsole=1980@192.168.74.17/eth0,1975@192.168.74.24/00:50:8d:91:d9:f0
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Memory: 253772k/260864k available (2381k kernel code, 6640k reserved, 1365k data, 284k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffe3000 - 0xfffff000 ( 112 kB)
[ 0.000000] vmalloc : 0xd06c0000 - 0xfffe1000 ( 761 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcfec0000 ( 254 MB)
[ 0.000000] .init : 0xc13a9000 - 0xc13f0000 ( 284 kB)
[ 0.000000] .data : 0xc1253600 - 0xc13a8d20 (1365 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1253600 (2381 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 930.270 MHz processor.
[ 0.008004] Calibrating delay loop (skipped), value calculated using timer frequency.. 1860.54 BogoMIPS (lpj=3721080)
[ 0.008208] pid_max: default: 32768 minimum: 301
[ 0.008426] Mount-cache hash table entries: 512
[ 0.008800] mce: CPU supports 5 MCE banks
[ 0.008931] CPU: Intel Pentium III (Coppermine) stepping 06
[ 0.009089] ACPI: Core revision 20120111
[ 0.014061] ACPI: setting ELCR to 0200 (from 0e00)
[ 0.015242] Performance Events: p6 PMU driver.
[ 0.015358] ... version: 0
[ 0.015450] ... bit width: 32
[ 0.015543] ... generic registers: 2
[ 0.015635] ... value mask: 00000000ffffffff
[ 0.015731] ... max period: 000000007fffffff
[ 0.015828] ... fixed-purpose events: 0
[ 0.015921] ... event mask: 0000000000000003
[ 0.016210] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.020001] NET: Registered protocol family 16
[ 0.020001] ACPI: bus type pci registered
[ 0.020001] PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=1
[ 0.020001] PCI: Using configuration type 1 for base access
[ 0.025178] bio: create slab <bio-0> at 0
[ 0.025598] ACPI: Added _OSI(Module Device)
[ 0.025700] ACPI: Added _OSI(Processor Device)
[ 0.025801] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.025901] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.029021] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.035893] ACPI: Interpreter enabled
[ 0.036019] ACPI: (supports S0 S5)
[ 0.036150] ACPI: Using PIC for interrupt routing
[ 0.040239] ACPI: Power Resource [FDDP] (off)
[ 0.041042] ACPI: Power Resource [URP1] (off)
[ 0.041866] ACPI: Power Resource [URP2] (off)
[ 0.042263] ACPI: Power Resource [LPTP] (off)
[ 0.047848] ACPI: No dock devices found.
[ 0.047978] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.048729] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.049988] PCI host bridge to bus 0000:00
[ 0.050089] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.050189] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.051366] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.052417] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.056124] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
[ 0.056466] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12)
[ 0.056792] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.057213] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12)
[ 0.057534] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12)
[ 0.057859] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.058280] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.058700] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12)
[ 0.059320] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.059516] vgaarb: loaded
[ 0.059610] vgaarb: bridge control possible 0000:00:02.0
[ 0.060247] SCSI subsystem initialized
[ 0.061156] PCI: Using ACPI for IRQ routing
[ 0.062055] pnp: PnP ACPI init
[ 0.062176] ACPI: bus type pnp registered
[ 0.069500] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.069620] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.069729] system 00:0c: [mem 0x00100000-0x0fefffff] could not be reserved
[ 0.069863] pnp: PnP ACPI: found 13 devices
[ 0.069963] ACPI: ACPI bus type pnp unregistered
[ 0.111918] Switching to clocksource acpi_pm
[ 0.112079] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[ 0.112185] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
[ 0.112296] pci 0000:00:1e.0: bridge window [mem 0xff800000-0xff8fffff]
[ 0.112405] pci 0000:00:1e.0: bridge window [mem 0xf6a00000-0xf6afffff pref]
[ 0.112807] NET: Registered protocol family 2
[ 0.113046] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.113392] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.113707] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.113911] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.114014] TCP reno registered
[ 0.114113] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.114226] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.114498] NET: Registered protocol family 1
[ 0.114737] pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.117097] VFS: Disk quotas dquot_6.5.2
[ 0.117248] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.117552] msgmni has been set to 495
[ 0.118165] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.118358] io scheduler noop registered
[ 0.118481] io scheduler cfq registered (default)
[ 0.119025] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.392083] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.668081] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.690295] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.710933] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.711547] Non-volatile memory driver v1.3
[ 0.711654] Linux agpgart interface v0.103
[ 0.711795] agpgart-intel 0000:00:00.0: Intel i815 Chipset
[ 0.711941] agpgart-intel 0000:00:00.0: detected gtt size: 65536K total, 65536K mappable
[ 0.712863] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 0.713087] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[ 0.713272] Hangcheck: Using getrawmonotonic().
[ 0.713478] [drm] Initialized drm 1.1.0 20060810
[ 0.713833] Floppy drive(s): fd0 is 1.44M
[ 0.731413] FDC 0 is a post-1991 82077
[ 0.734129] scsi0 : ata_piix
[ 0.734521] scsi1 : ata_piix
[ 0.737239] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.737358] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.737993] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 0.738097] e100: Copyright(c) 1999-2006 Intel Corporation
[ 0.738511] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[ 0.761695] e100 0000:01:08.0: eth0: addr 0xff86f000, irq 11, MAC addr 00:03:47:a4:64:d5
[ 0.762240] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.765652] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.765844] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.766395] mousedev: PS/2 mouse device common for all mice
[ 0.766827] rtc_cmos 00:02: RTC can wake from S4
[ 0.767132] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.767265] rtc0: alarms up to one month, 114 bytes nvram
[ 0.767456] cpuidle: using governor ladder
[ 0.767554] cpuidle: using governor menu
[ 0.769063] TCP cubic registered
[ 0.771339] NET: Registered protocol family 17
[ 0.771470] Registering the dns_resolver key type
[ 0.771600] Using IPI Shortcut mode
[ 0.772140] netconsole: local port 1980
[ 0.772244] netconsole: local IP 192.168.74.17
[ 0.772343] netconsole: interface 'eth0'
[ 0.772439] netconsole: remote port 1975
[ 0.772536] netconsole: remote IP 192.168.74.24
[ 0.772636] netconsole: remote ethernet address 00:50:8d:91:d9:f0
[ 0.772787] netconsole: device eth0 not up yet, forcing it
[ 0.789721] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.792173] e100 0000:01:08.0: eth0: NIC Link is Up 100 Mbps Full Duplex
[ 0.796023] netconsole: carrier detect appears untrustworthy, waiting 4 seconds
[ 0.956500] ata1.00: ATA-6: ST380011A, 8.01, max UDMA/100
[ 0.956605] ata1.00: 156301488 sectors, multi 16: LBA48
[ 0.972370] ata1.00: configured for UDMA/100
[ 0.972800] scsi 0:0:0:0: Direct-Access ATA ST380011A 8.01 PQ: 0 ANSI: 5
[ 0.973638] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 0.973964] sd 0:0:0:0: [sda] Write Protect is off
[ 0.974129] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.995686] sda: sda1 sda2 sda3
[ 0.996805] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.112032] Refined TSC clocksource calibration: 930.314 MHz.
[ 1.112149] Switching to clocksource tsc
[ 4.801225] console [netcon0] enabled
[ 4.801357] netconsole: network logging started
[ 4.801532] rtc_cmos 00:02: setting system clock to 2012-02-20 12:55:15 UTC (1329742515)
[ 4.817157] EXT3-fs (sda1): recovery required on readonly filesystem
[ 4.817290] EXT3-fs (sda1): write access will be enabled during recovery
[ 5.283547] kjournald starting. Commit interval 5 seconds
[ 5.283909] EXT3-fs (sda1): recovery complete
[ 5.284026] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 5.284171] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[ 5.284359] Freeing unused kernel memory: 284k freed
[ 5.285311] Write protecting the kernel text: 2384k
[ 5.285522] Write protecting the kernel read-only data: 1196k
[ 7.550607] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 7.550827] ACPI: Power Button [PBTN]
[ 7.551139] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 7.551322] ACPI: Power Button [PWRF]
[ 7.659948] parport_pc 00:0a: reported by Plug and Play ACPI
[ 7.660246] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 7.989627] usbcore: registered new interface driver usbfs
[ 7.990381] usbcore: registered new interface driver hub
[ 7.991881] usbcore: registered new device driver usb
[ 8.062219] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.140339] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
[ 8.148670] uhci_hcd: USB Universal Host Controller Interface driver
[ 8.149220] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 8.149363] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 8.149481] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[ 8.149716] uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000ef40
[ 8.149910] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.150031] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.150223] usb usb1: Product: UHCI Host Controller
[ 8.150325] usb usb1: Manufacturer: Linux 3.3.0-rc4 uhci_hcd
[ 8.150434] usb usb1: SerialNumber: 0000:00:1f.2
[ 8.150793] hub 1-0:1.0: USB hub found
[ 8.150908] hub 1-0:1.0: 2 ports detected
[ 8.151363] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[ 8.151504] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[ 8.151622] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
[ 8.151858] uhci_hcd 0000:00:1f.4: irq 10, io base 0x0000ef80
[ 8.159500] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.159644] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.159874] usb usb2: Product: UHCI Host Controller
[ 8.159978] usb usb2: Manufacturer: Linux 3.3.0-rc4 uhci_hcd
[ 8.160141] usb usb2: SerialNumber: 0000:00:1f.4
[ 8.165932] hub 2-0:1.0: USB hub found
[ 8.166086] hub 2-0:1.0: 2 ports detected
[ 9.396043] intel8x0_measure_ac97_clock: measured 52271 usecs (2926 samples)
[ 9.396191] intel8x0: clocking to 41159
[ 10.231275] Adding 1048572k swap on /dev/sda2. Priority:-1 extents:1 across:1048572k
[ 10.476088] EXT3-fs (sda1): using internal journal
[ 10.595095] NTFS driver 2.1.30 [Flags: R/W MODULE].
[ 10.824763] usbcore: registered new interface driver libusual
[ 10.830985] Initializing USB Mass Storage driver...
[ 10.832120] usbcore: registered new interface driver usb-storage
[ 10.832255] USB Mass Storage support registered.
[ 10.885221] smsc47m1: Found SMSC LPC47M10x/LPC47M112/LPC47M13x
[ 10.885384] ACPI Warning: 0x00000804-0x00000804 SystemIO conflicts with Region \_SB_.PCI0.SBRG.RNT3 1 (20120111/utaddress-251)
[ 10.885622] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.766616] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 13.138202] NET: Registered protocol family 8
[ 13.138341] NET: Registered protocol family 20
[ 15.402941] NET: Registered protocol family 10
[ 17.837703] RPC: Registered named UNIX socket transport module.
[ 17.837917] RPC: Registered udp transport module.
[ 17.838021] RPC: Registered tcp transport module.
[ 17.838125] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 17.938275] Registering the id_resolver key type
[ 17.969638] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 18.725603] fuse init (API version 7.18)
[ 20.391759] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input3
[ 20.915381] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 20.928931] NFSD: starting 90-second grace period
[ 23.179451] lp0: using parport0 (interrupt-driven).
[ 23.192176] ppdev: user-space parallel port driver
[ 23.264048] BUG: unable to handle kernel NULL pointer dereference at 00000004
[ 23.264241] IP: [<c11e4cfa>] __neigh_for_each_release+0x7c/0x92
[ 23.264385] *pde = 00000000
[ 23.264493] Oops: 0000 [#1] PREEMPT
[ 23.264616] Modules linked in: ppdev lp uinput fuse nfsd nfs lockd auth_rpcgss nfs_acl sunrpc ipv6 clip atm ext4 jbd2 adm1025 hwmon_vid hwmon usb_storage usb_libusual udf crc_itu_t isofs zlib_inflate vfat fat eeprom ntfs snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device snd uhci_hcd i2c_i801 ehci_hcd evdev serio_raw usbcore usb_common soundcore snd_page_alloc parport_pc parport button processor
[ 23.265997]
[ 23.266098] Pid: 0, comm: swapper Not tainted 3.3.0-rc4 #16 /D815EEA2
[ 23.266330] EIP: 0060:[<c11e4cfa>] EFLAGS: 00010286 CPU: 0
[ 23.266438] EIP is at __neigh_for_each_release+0x7c/0x92
[ 23.266544] EAX: d08f036c EBX: 00000000 ECX: 00000000 EDX: d08edf38
[ 23.266655] ESI: 00000000 EDI: d08ede2b EBP: cf809f78 ESP: cf809f60
[ 23.266766] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[ 23.266875] Process swapper (pid: 0, ti=cf808000 task=c1388460 task.ti=c1380000)
[ 23.267065] Stack:
[ 23.267163] cf97d8a0 cf97d8a0 d08edf38 00000100 c141bc80 d08ede2b cf809f80 d08ede47
[ 23.267455] cf809fc4 c1022309 cf809fac c118a00d cf809fac c1030e0e cd5dc390 00000001
[ 23.267756] c141c68c c141c48c 00000000 cf809fb0 cf809fb0 cf809fb0 c141bb5c 00000001
[ 23.268004] Call Trace:
[ 23.268004] [<d08edf38>] ? clip_seq_show+0x3b/0x3b [clip]
[ 23.268004] [<d08ede2b>] ? clip_seq_start+0x21/0x21 [clip]
[ 23.268004] [<d08ede47>] idle_timer_check+0x1c/0x4a [clip]
[ 23.268004] [<c1022309>] run_timer_softirq+0x140/0x1de
[ 23.268004] [<c118a00d>] ? scsi_softirq_done+0xbf/0xc7
[ 23.268004] [<c1030e0e>] ? put_cred_rcu+0x6f/0x76
[ 23.268004] [<c101e24a>] __do_softirq+0x5f/0xe8
[ 23.268004] [<c101e1eb>] ? send_remote_softirq+0x18/0x18
[ 23.268004] <IRQ>
[ 23.268004] [<c101e44b>] ? irq_exit+0x34/0x8b
[ 23.268004] [<c1012644>] ? smp_apic_timer_interrupt+0x6e/0x79
[ 23.268004] [<c125225d>] ? apic_timer_interrupt+0x31/0x38
[ 23.268004] [<c1006f7e>] ? default_idle+0x29/0x3e
[ 23.268004] [<c1001574>] ? cpu_idle+0x73/0xa6
[ 23.268004] [<c1243453>] ? rest_init+0x77/0x79
[ 23.268004] [<c13a9653>] ? start_kernel+0x296/0x29c
[ 23.268004] [<c13a91ca>] ? obsolete_checksetup+0x8b/0x8b
[ 23.268004] [<c13a9044>] ? i386_start_kernel+0x44/0x46
[ 23.268004] Code: 14 8b 52 08 f6 c2 08 74 0b 89 45 e8 e8 31 ca 06 00 8b 45 e8 85 c0 74 07 89 f8 e8 5c ff ff ff 8b 3b 85 ff 75 b2 89 f3 8b 75 ec 43 <8b> 4e 04 b8 01 00 00 00 d3 e0 39 c3 7c 8c 83 c4 0c 5b 5e 5f 5d
[ 23.268004] EIP: [<c11e4cfa>] __neigh_for_each_release+0x7c/0x92 SS:ESP 0068:cf809f60
[ 23.268004] CR2: 0000000000000004
[ 23.271899] ---[ end trace f4b1cbf2fb401c6c ]---
[ 23.272011] Kernel panic - not syncing: Fatal exception in interrupt
Coming from 32092ecf0644
(atm: clip: Use device neigh support on top of "arp_tbl".)
David forgot to remove clip_tbl for good
But I dont know enough this code to know if the following patch is the
way to fix this. (and __neigh_for_each_release() can also be deleted if
no users left in tree)
net/atm/clip.c | 53 -----------------------------------------------
1 file changed, 53 deletions(-)
diff --git a/net/atm/clip.c b/net/atm/clip.c
index c12c258..ca780ff 100644
--- a/net/atm/clip.c
+++ b/net/atm/clip.c
@@ -46,8 +46,6 @@
static struct net_device *clip_devs;
static struct atm_vcc *atmarpd;
-static struct neigh_table clip_tbl;
-static struct timer_list idle_timer;
static int to_atmarpd(enum atmarp_ctrl_type type, int itf, __be32 ip)
{@@ -117,49 +115,6 @@ out:
netif_tx_unlock_bh(entry->neigh->dev);
}
-/* The neighbour entry n->lock is held. */
-static int neigh_check_cb(struct neighbour *n)
-{
- struct atmarp_entry *entry = neighbour_priv(n);
- struct clip_vcc *cv;
-
- for (cv = entry->vccs; cv; cv = cv->next) {
- unsigned long exp = cv->last_use + cv->idle_timeout;
-
- if (cv->idle_timeout && time_after(jiffies, exp)) {
- pr_debug("releasing vcc %p->%p of entry %p\n",
- cv, cv->vcc, entry);
- vcc_release_async(cv->vcc, -ETIMEDOUT);
- }
- }
-
- if (entry->vccs || time_before(jiffies, entry->expires))
- return 0;
-
- if (atomic_read(&n->refcnt) > 1) {
- struct sk_buff *skb;
-
- pr_debug("destruction postponed with ref %d\n",
- atomic_read(&n->refcnt));
-
- while ((skb = skb_dequeue(&n->arp_queue)) != NULL)
- dev_kfree_skb(skb);
-
- return 0;
- }
-
- pr_debug("expired neigh %p\n", n);
- return 1;
-}
-
-static void idle_timer_check(unsigned long dummy)
-{
- write_lock(&clip_tbl.lock);
- __neigh_for_each_release(&clip_tbl, neigh_check_cb);
- mod_timer(&idle_timer, jiffies + CLIP_CHECK_INTERVAL * HZ);
- write_unlock(&clip_tbl.lock);
-}
-
static int clip_arp_rcv(struct sk_buff *skb)
{
struct atm_vcc *vcc;@@ -622,8 +577,6 @@ static int atm_init_atmarp(struct atm_vcc *vcc)
return -EADDRINUSE;
}
- mod_timer(&idle_timer, jiffies + CLIP_CHECK_INTERVAL * HZ);
-
atmarpd = vcc;
set_bit(ATM_VF_META, &vcc->flags);
set_bit(ATM_VF_READY, &vcc->flags);
@@ -871,7 +824,6 @@ static int __init atm_clip_init(void)
register_netdevice_notifier(&clip_dev_notifier);
register_inetaddr_notifier(&clip_inet_notifier);
- setup_timer(&idle_timer, idle_timer_check, 0);
#ifdef CONFIG_PROC_FS
{@@ -898,11 +850,6 @@ static void atm_clip_exit_noproc(void)
deregister_atm_ioctl(&clip_ioctl_ops);
- /* First, stop the idle timer, so it stops banging
- * on the table.
- */
- del_timer_sync(&idle_timer);
-
dev = clip_devs;
while (dev) {
next = PRIV(dev)->next;Le mardi 21 février 2012 à 14:07 -0500, David Miller a écrit :
From: Eric Dumazet <redacted>
Date: Tue, 21 Feb 2012 20:03:24 +0100
quoted
But I dont know enough this code to know if the following patch is the
way to fix this. (and __neigh_for_each_release() can also be deleted if
no users left in tree)
I think instead of removing the code, we need to have it iterate over
"arp_tbl" but only invoke the callback for devices which are of type
ATM.
That makes sense...
Or invoke callback for all entries, and filter in callback non ATM ones.
Le mardi 21 février 2012 à 20:15 +0100, Eric Dumazet a écrit :
Le mardi 21 février 2012 à 14:07 -0500, David Miller a écrit :
quoted
From: Eric Dumazet <redacted>
Date: Tue, 21 Feb 2012 20:03:24 +0100
quoted
But I dont know enough this code to know if the following patch is the
way to fix this. (and __neigh_for_each_release() can also be deleted if
no users left in tree)
I think instead of removing the code, we need to have it iterate over
"arp_tbl" but only invoke the callback for devices which are of type
ATM.
That makes sense...
Or invoke callback for all entries, and filter in callback non ATM ones.
What about following patch ?
Meelis, can you test it please ?
[PATCH] atm: clip: remove clip_tbl
Commit 32092ecf0644 (atm: clip: Use device neigh support on top of
"arp_tbl".) introduced a bug since clip_tbl is zeroed : Crash occurs in
__neigh_for_each_release()
idle_timer_check() must use instead arp_tbl and neigh_check_cb() should
ignore non clip neighbours.
Idea from David Miller.
Reported-by: Meelis Roos <redacted>
Signed-off-by: Eric Dumazet <redacted>
---
net/atm/clip.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/net/atm/clip.c b/net/atm/clip.c
index c12c258..127fe70 100644
--- a/net/atm/clip.c
+++ b/net/atm/clip.c
@@ -46,8 +46,8 @@
static struct net_device *clip_devs;
static struct atm_vcc *atmarpd;
-static struct neigh_table clip_tbl;
static struct timer_list idle_timer;
+static const struct neigh_ops clip_neigh_ops;
static int to_atmarpd(enum atmarp_ctrl_type type, int itf, __be32 ip)
{@@ -123,6 +123,8 @@ static int neigh_check_cb(struct neighbour *n)
struct atmarp_entry *entry = neighbour_priv(n);
struct clip_vcc *cv;
+ if (n->ops != &clip_neigh_ops)
+ return 0;
for (cv = entry->vccs; cv; cv = cv->next) {
unsigned long exp = cv->last_use + cv->idle_timeout;
@@ -154,10 +156,10 @@ static int neigh_check_cb(struct neighbour *n)
static void idle_timer_check(unsigned long dummy)
{
- write_lock(&clip_tbl.lock);
- __neigh_for_each_release(&clip_tbl, neigh_check_cb);
+ write_lock(&arp_tbl.lock);
+ __neigh_for_each_release(&arp_tbl, neigh_check_cb);
mod_timer(&idle_timer, jiffies + CLIP_CHECK_INTERVAL * HZ);
- write_unlock(&clip_tbl.lock);
+ write_unlock(&arp_tbl.lock);
}
static int clip_arp_rcv(struct sk_buff *skb)From: Eric Dumazet <redacted>
Date: Tue, 21 Feb 2012 21:46:49 +0100
[PATCH] atm: clip: remove clip_tbl
Commit 32092ecf0644 (atm: clip: Use device neigh support on top of
"arp_tbl".) introduced a bug since clip_tbl is zeroed : Crash occurs in
__neigh_for_each_release()
idle_timer_check() must use instead arp_tbl and neigh_check_cb() should
ignore non clip neighbours.
Idea from David Miller.
Reported-by: Meelis Roos <redacted>
Signed-off-by: Eric Dumazet <redacted>
Yep, this looks a lot better, once we have positive testing from
Meelis I'll apply this.
Thanks.