[PATCH V2 3/4] CS89x0 : add CS89x0 platform device to the iMX31ADS board

@@ -66,6 +66,8 @@ CONFIG_NETDEVICES=y
 CONFIG_SMSC_PHY=y
 CONFIG_NET_ETHERNET=y
 CONFIG_SMSC911X=y
+CONFIG_CS89x0=y
+CONFIG_CS89x0_PLATFORM=y
 CONFIG_DNET=y
 # CONFIG_NETDEV_1000 is not set
 # CONFIG_NETDEV_10000 is not set

@@ -28,7 +28,6 @@
 #include <asm/memory.h>
 #include <asm/mach/map.h>
 #include <mach/common.h>
-#include <mach/board-mx31ads.h>
 #include <mach/iomux-mx3.h>
 
 #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1

@@ -39,6 +38,9 @@
 
 #include "devices-imx31.h"
 
+/* Base address of PBC controller */
+#define PBC_BASE_ADDRESS	MX31_CS4_BASE_ADDR_VIRT
+
 /* PBC Board interrupt status register */
 #define PBC_INTSTATUS           0x000016
 

@@ -62,10 +64,12 @@
 #define PBC_INTMASK_CLEAR_REG	(PBC_INTMASK_CLEAR + PBC_BASE_ADDRESS)
 #define EXPIO_PARENT_INT	IOMUX_TO_IRQ(MX31_PIN_GPIO1_4)
 
+#define MXC_EXP_IO_BASE		MXC_BOARD_IRQ_START
 #define MXC_IRQ_TO_EXPIO(irq)	((irq) - MXC_EXP_IO_BASE)
 
 #define EXPIO_INT_XUART_INTA	(MXC_EXP_IO_BASE + 10)
 #define EXPIO_INT_XUART_INTB	(MXC_EXP_IO_BASE + 11)
+#define EXPIO_INT_ENET_INT	(MXC_EXP_IO_BASE + 8)
 
 #define MXC_MAX_EXP_IO_LINES	16
 

@@ -101,11 +105,36 @@ static struct platform_device serial_device = {
 	},
 };
 
+static struct resource mx31ads_cs8900_resources[] = {
+	{
+		.start	= MX31_CS4_BASE_ADDR + 0x20000 + 0x300,
+		.end	= MX31_CS4_BASE_ADDR + 0x20000 + 0x1000 - 1,
+		.flags	= IORESOURCE_MEM
+	},
+	{
+		.start	= EXPIO_INT_ENET_INT,
+		.end	= EXPIO_INT_ENET_INT,
+		.flags	= IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device mx31ads_cs8900_device = {
+	.name		= "cs89x0",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(mx31ads_cs8900_resources),
+	.resource	= mx31ads_cs8900_resources
+};
+
 static int __init mxc_init_extuart(void)
 {
 	return platform_device_register(&serial_device);
 }
 
+static void __init mxc_init_ext_ethernet(void)
+{
+	platform_device_register(&mx31ads_cs8900_device);
+}
+
 static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };

@@ -497,7 +526,7 @@ static struct map_desc mx31ads_io_desc[] __initdata = {
 	{
 		.virtual	= MX31_CS4_BASE_ADDR_VIRT,
 		.pfn		= __phys_to_pfn(MX31_CS4_BASE_ADDR),
-		.length		= MX31_CS4_SIZE / 2,
+		.length		= 0x20000,
 		.type		= MT_DEVICE
 	},
 };

@@ -522,6 +551,7 @@ static void __init mx31ads_init(void)
 	mxc_init_imx_uart();
 	mxc_init_i2c();
 	mxc_init_audio();
+	mxc_init_ext_ethernet();
 }
 
 static void __init mx31ads_timer_init(void)

@@ -1,33 +0,0 @@
-/*
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31ADS_H__
-#define __ASM_ARCH_MXC_BOARD_MX31ADS_H__
-
-#include <mach/hardware.h>
-
-/*
- * These symbols are used by drivers/net/cs89x0.c.
- * This is ugly as hell, but we have to provide them until
- * someone fixed the driver.
- */
-
-/* Base address of PBC controller */
-#define PBC_BASE_ADDRESS        MX31_CS4_BASE_ADDR_VIRT
-/* Offsets for the PBC Controller register */
-
-/* Ethernet Controller IO base address */
-#define PBC_CS8900A_IOBASE      0x020000
-
-#define MXC_EXP_IO_BASE		(MXC_BOARD_IRQ_START)
-
-#define EXPIO_INT_ENET_INT	(MXC_EXP_IO_BASE + 8)
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31ADS_H__ */

@@ -191,8 +191,7 @@ static struct devprobe2 isa_probes[] __initdata = {
 #endif
 #ifdef CONFIG_CS89x0
 #if !defined(CONFIG_CS89x0_PLATFORM) || defined(CONFIG_MACH_IXDP2351) || \
-	defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_MACH_QQ2440) || \
-	defined(CONFIG_MACH_MX31ADS)
+	defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_MACH_QQ2440)
  	{cs89x0_probe, 0},
 #endif
 #endif

@@ -185,12 +185,6 @@ static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
 #include <mach/qq2440.h>
 static unsigned int netcard_portlist[] __used __initdata = { QQ2440_CS8900_VIRT_BASE + 0x300, 0 };
 static unsigned int cs8900_irq_map[] = { QQ2440_CS8900_IRQ, 0, 0, 0 };
-#elif defined(CONFIG_MACH_MX31ADS)
-#include <mach/board-mx31ads.h>
-static unsigned int netcard_portlist[] __used __initdata = {
-	PBC_BASE_ADDRESS + PBC_CS8900A_IOBASE + 0x300, 0
-};
-static unsigned cs8900_irq_map[] = {EXPIO_INT_ENET_INT, 0, 0, 0};
 #endif
 #else
 static unsigned int netcard_portlist[] __used __initdata =

@@ -303,8 +297,7 @@ __setup("cs89x0_media=", media_fn);
 
 
 #if !defined(CONFIG_CS89x0_PLATFORM) || defined(CONFIG_MACH_IXDP2351) || \
-	defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_MACH_QQ2440) ||  \
-	defined(CONFIG_MACH_MX31ADS)
+	defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_MACH_QQ2440)
 /* Check for a network adaptor of this type, and return '0' iff one exists.
    If dev->base_addr == 0, probe all likely locations.
    If dev->base_addr == 1, always return failure.

@@ -1180,8 +1173,7 @@ write_irq(struct net_device *dev, int chip_type, int irq)
 
 	if (chip_type == CS8900) {
 #if !defined(CONFIG_CS89x0_PLATFORM) || defined(CONFIG_MACH_IXDP2351) || \
-	defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_MACH_QQ2440) ||  \
-	defined(CONFIG_MACH_MX31ADS)
+	defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_MACH_QQ2440)
 		/* Search the mapping table for the corresponding IRQ pin. */
 		for (i = 0; i != ARRAY_SIZE(cs8900_irq_map); i++)
 			if (cs8900_irq_map[i] == irq)