00:0a.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
Memory at e3020000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b000 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
00:0a.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 12
Memory at e3000000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b400 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
[ 950.132046] Stopping tasks ... done.
[ 950.459794] Suspending console(s)
[ 951.776277] pnp: Device 00:0c disabled.
[ 951.776673] pnp: Device 00:0a disabled.
[ 951.776984] pnp: Device 00:09 disabled.
[ 951.777306] pnp: Device 00:08 disabled.
[ 951.777786] ACPI: PCI interrupt for device 0000:00:11.5 disabled
[ 951.995359] ACPI: PCI interrupt for device 0000:00:11.3 disabled
[ 952.006094] ACPI: PCI interrupt for device 0000:00:11.2 disabled
[ 952.022243] ACPI handle has no context!
[ 952.033068] ACPI: PCI interrupt for device 0000:00:0c.2 disabled
[ 952.044086] ACPI: PCI interrupt for device 0000:00:0c.1 disabled
[ 952.055083] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 952.282211] ACPI: PCI interrupt for device 0000:00:0a.1 disabled
[ 952.282221] ACPI handle has no context!
[ 952.537474] ACPI: PCI interrupt for device 0000:00:0a.0 disabled
[ 952.537495] ACPI handle has no context!
[ 956.857085] Back to C!
[ 957.295035] ACPI: Unable to turn cooling device [b18d0e00] 'off'
[ 957.521400] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 957.521478] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 957.532256] PM: Writing back config space on device 0000:00:0a.0 at offset f (was ff0100, writing ff0105)
[ 957.532277] PM: Writing back config space on device 0000:00:0a.0 at offset 8 (was 1, writing b001)
[ 957.532291] PM: Writing back config space on device 0000:00:0a.0 at offset 4 (was 4, writing e3020004)
[ 957.532299] PM: Writing back config space on device 0000:00:0a.0 at offset 3 (was 800000, writing 802008)
[ 957.532309] PM: Writing back config space on device 0000:00:0a.0 at offset 1 (was 2300000, writing 2300007)
[ 957.532339] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 957.567251] PM: Writing back config space on device 0000:00:0a.1 at offset f (was ff0200, writing ff020c)
[ 957.567275] PM: Writing back config space on device 0000:00:0a.1 at offset 8 (was 1, writing b401)
[ 957.567290] PM: Writing back config space on device 0000:00:0a.1 at offset 4 (was 4, writing e3000004)
[ 957.567298] PM: Writing back config space on device 0000:00:0a.1 at offset 3 (was 800000, writing 802008)
[ 957.567308] PM: Writing back config space on device 0000:00:0a.1 at offset 1 (was 2300000, writing 2300007)
[ 957.567346] ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.589975] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.600217] ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 957.611230] ACPI: PCI Interrupt 0000:00:0c.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 957.838282] ACPI: PCI Interrupt 0000:00:0c.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 957.902166] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[e3046000-e30467ff] Max Packet=[512] IR/IT contexts=[4/8]
[ 957.911656] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 957.911666] PCI: VIA VLink IRQ fixup for 0000:00:11.1, from 255 to 11
[ 957.922034] ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.933028] ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.944076] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 957.944091] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 957.946061] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 957.947464] pnp: Device 00:08 activated.
[ 957.948724] pnp: Device 00:09 activated.
[ 957.950635] pnp: Device 00:0a activated.
[ 957.950664] pnp: Failed to activate device 00:0b.
[ 957.951942] pnp: Device 00:0c activated.
[ 959.883939] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 961.866287] hde: selected mode 0x45
[ 965.310493] hdg: selected mode 0x45
[ 965.316152] hdh: selected mode 0x42
[ 969.135523] hda: selected mode 0x46
[ 973.454631] hdb: selected mode 0x45
[ 973.457179] hdc: selected mode 0x44
[ 973.459550] hdd: selected mode 0x42
[ 973.950474] Restarting tasks ... done.
[ 974.261357] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 974.262099] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 974.262620] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 974.262894] [drm] Loading R200 Microcode
eth0 now doesn't receive anything - it's transmitting ok because
I can receive its packets on another host. It's also still getting
interrupts.
If I then ifconfig eth0 down and up, or change the MTU (since
that resets the link on e1000), it starts working again:
[ 993.926603] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
There's a link up at 959.883939 too...
--
Simon Arlott
Simon Arlott wrote:
00:0a.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
Memory at e3020000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b000 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
00:0a.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 12
Memory at e3000000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b400 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
[ 950.132046] Stopping tasks ... done.
[ 950.459794] Suspending console(s)
[ 951.776277] pnp: Device 00:0c disabled.
[ 951.776673] pnp: Device 00:0a disabled.
[ 951.776984] pnp: Device 00:09 disabled.
[ 951.777306] pnp: Device 00:08 disabled.
[ 951.777786] ACPI: PCI interrupt for device 0000:00:11.5 disabled
[ 951.995359] ACPI: PCI interrupt for device 0000:00:11.3 disabled
[ 952.006094] ACPI: PCI interrupt for device 0000:00:11.2 disabled
[ 952.022243] ACPI handle has no context!
[ 952.033068] ACPI: PCI interrupt for device 0000:00:0c.2 disabled
[ 952.044086] ACPI: PCI interrupt for device 0000:00:0c.1 disabled
[ 952.055083] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 952.282211] ACPI: PCI interrupt for device 0000:00:0a.1 disabled
[ 952.282221] ACPI handle has no context!
[ 952.537474] ACPI: PCI interrupt for device 0000:00:0a.0 disabled
[ 952.537495] ACPI handle has no context!
[ 956.857085] Back to C!
[ 957.295035] ACPI: Unable to turn cooling device [b18d0e00] 'off'
[ 957.521400] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 957.521478] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 957.532256] PM: Writing back config space on device 0000:00:0a.0 at offset f (was ff0100, writing ff0105)
[ 957.532277] PM: Writing back config space on device 0000:00:0a.0 at offset 8 (was 1, writing b001)
[ 957.532291] PM: Writing back config space on device 0000:00:0a.0 at offset 4 (was 4, writing e3020004)
[ 957.532299] PM: Writing back config space on device 0000:00:0a.0 at offset 3 (was 800000, writing 802008)
[ 957.532309] PM: Writing back config space on device 0000:00:0a.0 at offset 1 (was 2300000, writing 2300007)
[ 957.532339] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 957.567251] PM: Writing back config space on device 0000:00:0a.1 at offset f (was ff0200, writing ff020c)
[ 957.567275] PM: Writing back config space on device 0000:00:0a.1 at offset 8 (was 1, writing b401)
[ 957.567290] PM: Writing back config space on device 0000:00:0a.1 at offset 4 (was 4, writing e3000004)
[ 957.567298] PM: Writing back config space on device 0000:00:0a.1 at offset 3 (was 800000, writing 802008)
[ 957.567308] PM: Writing back config space on device 0000:00:0a.1 at offset 1 (was 2300000, writing 2300007)
[ 957.567346] ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.589975] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.600217] ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 957.611230] ACPI: PCI Interrupt 0000:00:0c.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 957.838282] ACPI: PCI Interrupt 0000:00:0c.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 957.902166] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[e3046000-e30467ff] Max Packet=[512] IR/IT contexts=[4/8]
[ 957.911656] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 957.911666] PCI: VIA VLink IRQ fixup for 0000:00:11.1, from 255 to 11
[ 957.922034] ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.933028] ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 957.944076] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 957.944091] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 957.946061] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 957.947464] pnp: Device 00:08 activated.
[ 957.948724] pnp: Device 00:09 activated.
[ 957.950635] pnp: Device 00:0a activated.
[ 957.950664] pnp: Failed to activate device 00:0b.
[ 957.951942] pnp: Device 00:0c activated.
[ 959.883939] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 961.866287] hde: selected mode 0x45
[ 965.310493] hdg: selected mode 0x45
[ 965.316152] hdh: selected mode 0x42
[ 969.135523] hda: selected mode 0x46
[ 973.454631] hdb: selected mode 0x45
[ 973.457179] hdc: selected mode 0x44
[ 973.459550] hdd: selected mode 0x42
[ 973.950474] Restarting tasks ... done.
[ 974.261357] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 974.262099] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 974.262620] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 974.262894] [drm] Loading R200 Microcode
eth0 now doesn't receive anything - it's transmitting ok because
I can receive its packets on another host. It's also still getting
interrupts.
If I then ifconfig eth0 down and up, or change the MTU (since
that resets the link on e1000), it starts working again:
[ 993.926603] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
There's a link up at 959.883939 too...
OK, I'll try to look into this coming week.
Can you run `ethtool -d ethX` immediately after resuming and post that output?
it might help to know that upfront.
Thanks,
Auke
On 06/08/07 04:01, Kok, Auke wrote:
Simon Arlott wrote:
quoted
00:0a.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet
Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
Memory at e3020000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b000 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
00:0a.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet
Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 12
Memory at e3000000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b400 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
[ 950.132046] Stopping tasks ... done.
[ 950.459794] Suspending console(s)
[ 951.776277] pnp: Device 00:0c disabled.
[ 951.776673] pnp: Device 00:0a disabled.
[ 951.776984] pnp: Device 00:09 disabled.
[ 951.777306] pnp: Device 00:08 disabled.
[ 951.777786] ACPI: PCI interrupt for device 0000:00:11.5 disabled
[ 951.995359] ACPI: PCI interrupt for device 0000:00:11.3 disabled
[ 952.006094] ACPI: PCI interrupt for device 0000:00:11.2 disabled
[ 952.022243] ACPI handle has no context!
[ 952.033068] ACPI: PCI interrupt for device 0000:00:0c.2 disabled
[ 952.044086] ACPI: PCI interrupt for device 0000:00:0c.1 disabled
[ 952.055083] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 952.282211] ACPI: PCI interrupt for device 0000:00:0a.1 disabled
[ 952.282221] ACPI handle has no context!
[ 952.537474] ACPI: PCI interrupt for device 0000:00:0a.0 disabled
[ 952.537495] ACPI handle has no context!
[ 956.857085] Back to C!
[ 957.295035] ACPI: Unable to turn cooling device [b18d0e00] 'off'
[ 957.521400] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 957.521478] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] ->
GSI 11 (level, low) -> IRQ 11
[ 957.532256] PM: Writing back config space on device 0000:00:0a.0 at
offset f (was ff0100, writing ff0105)
[ 957.532277] PM: Writing back config space on device 0000:00:0a.0 at
offset 8 (was 1, writing b001)
[ 957.532291] PM: Writing back config space on device 0000:00:0a.0 at
offset 4 (was 4, writing e3020004)
[ 957.532299] PM: Writing back config space on device 0000:00:0a.0 at
offset 3 (was 800000, writing 802008)
[ 957.532309] PM: Writing back config space on device 0000:00:0a.0 at
offset 1 (was 2300000, writing 2300007)
[ 957.532339] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] ->
GSI 5 (level, low) -> IRQ 5
[ 957.567251] PM: Writing back config space on device 0000:00:0a.1 at
offset f (was ff0200, writing ff020c)
[ 957.567275] PM: Writing back config space on device 0000:00:0a.1 at
offset 8 (was 1, writing b401)
[ 957.567290] PM: Writing back config space on device 0000:00:0a.1 at
offset 4 (was 4, writing e3000004)
[ 957.567298] PM: Writing back config space on device 0000:00:0a.1 at
offset 3 (was 800000, writing 802008)
[ 957.567308] PM: Writing back config space on device 0000:00:0a.1 at
offset 1 (was 2300000, writing 2300007)
[ 957.567346] ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKD] ->
GSI 12 (level, low) -> IRQ 12
[ 957.589975] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] ->
GSI 12 (level, low) -> IRQ 12
[ 957.600217] ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] ->
GSI 11 (level, low) -> IRQ 11
[ 957.611230] ACPI: PCI Interrupt 0000:00:0c.1[B] -> Link [LNKB] ->
GSI 11 (level, low) -> IRQ 11
[ 957.838282] ACPI: PCI Interrupt 0000:00:0c.2[C] -> Link [LNKC] ->
GSI 5 (level, low) -> IRQ 5
[ 957.902166] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11]
MMIO=[e3046000-e30467ff] Max Packet=[512] IR/IT contexts=[4/8]
[ 957.911656] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] ->
GSI 11 (level, low) -> IRQ 11
[ 957.911666] PCI: VIA VLink IRQ fixup for 0000:00:11.1, from 255 to 11
[ 957.922034] ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] ->
GSI 12 (level, low) -> IRQ 12
[ 957.933028] ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] ->
GSI 12 (level, low) -> IRQ 12
[ 957.944076] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] ->
GSI 5 (level, low) -> IRQ 5
[ 957.944091] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 957.946061] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] ->
GSI 11 (level, low) -> IRQ 11
[ 957.947464] pnp: Device 00:08 activated.
[ 957.948724] pnp: Device 00:09 activated.
[ 957.950635] pnp: Device 00:0a activated.
[ 957.950664] pnp: Failed to activate device 00:0b.
[ 957.951942] pnp: Device 00:0c activated.
[ 959.883939] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps
Full Duplex, Flow Control: RX/TX
[ 961.866287] hde: selected mode 0x45
[ 965.310493] hdg: selected mode 0x45
[ 965.316152] hdh: selected mode 0x42
[ 969.135523] hda: selected mode 0x46
[ 973.454631] hdb: selected mode 0x45
[ 973.457179] hdc: selected mode 0x44
[ 973.459550] hdd: selected mode 0x42
[ 973.950474] Restarting tasks ... done.
[ 974.261357] agpgart: Found an AGP 2.0 compliant device at
0000:00:00.0.
[ 974.262099] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x
mode
[ 974.262620] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x
mode
[ 974.262894] [drm] Loading R200 Microcode
eth0 now doesn't receive anything - it's transmitting ok because I can
receive its packets on another host. It's also still getting interrupts.
If I then ifconfig eth0 down and up, or change the MTU (since that
resets the link on e1000), it starts working again:
[ 993.926603] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps
Full Duplex, Flow Control: RX/TX
There's a link up at 959.883939 too...
OK, I'll try to look into this coming week.
Can you run `ethtool -d ethX` immediately after resuming and post that
output? it might help to know that upfront.
MAC Registers
-------------
0x00000: CTRL (Device control register) 0x18F00249
Endian mode (buffers): little
Link reset: reset
Set link up: 1
Invert Loss-Of-Signal: no
Receive flow control: enabled
Transmit flow control: enabled
VLAN mode: disabled
Auto speed detect: disabled
Speed select: 1000Mb/s
Force speed: no
Force duplex: no
0x00008: STATUS (Device status register) 0x0000C383
Duplex: full
Link up: link config
TBI mode: disabled
Link speed: 1000Mb/s
Bus type: PCI
Bus speed: 33MHz
Bus width: 32-bit
0x00100: RCTL (Receive control register) 0x02018022
Receiver: enabled
Store bad packets: disabled
Unicast promiscuous: disabled
Multicast promiscuous: disabled
Long packet: enabled
Descriptor minimum threshold size: 1/2
Broadcast accept mode: accept
VLAN filter: disabled
Cononical form indicator: disabled
Discard pause frames: filtered
Pass MAC control frames: don't pass
Receive buffer size: 16384
0x02808: RDLEN (Receive desc length) 0x00001000
0x02810: RDH (Receive desc head) 0x00000000
0x02818: RDT (Receive desc tail) 0x00000000
0x02820: RDTR (Receive delay timer) 0x00000000
0x00400: TCTL (Transmit ctrl register) 0x0103F0FA
Transmitter: enabled
Pad short packets: enabled
Software XOFF Transmission: disabled
Re-transmit on late collision: enabled
0x03808: TDLEN (Transmit desc length) 0x00001000
0x03810: TDH (Transmit desc head) 0x0000005C
0x03818: TDT (Transmit desc tail) 0x0000005C
0x03820: TIDV (Transmit delay timer) 0x00000008
PHY type: M88
--
Simon Arlott
Hi!
quoted
00:0a.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet
Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
Memory at e3020000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b000 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
00:0a.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet
Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 12
Memory at e3000000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b400 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
[ 950.132046] Stopping tasks ... done.
[ 950.459794] Suspending console(s)
[ 951.776277] pnp: Device 00:0c disabled.
[ 951.776673] pnp: Device 00:0a disabled.
[ 951.776984] pnp: Device 00:09 disabled.
[ 951.777306] pnp: Device 00:08 disabled.
[ 951.777786] ACPI: PCI interrupt for device 0000:00:11.5 disabled
[ 951.995359] ACPI: PCI interrupt for device 0000:00:11.3 disabled
[ 952.006094] ACPI: PCI interrupt for device 0000:00:11.2 disabled
[ 952.022243] ACPI handle has no context!
[ 952.033068] ACPI: PCI interrupt for device 0000:00:0c.2 disabled
[ 952.044086] ACPI: PCI interrupt for device 0000:00:0c.1 disabled
[ 952.055083] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 952.282211] ACPI: PCI interrupt for device 0000:00:0a.1 disabled
[ 952.282221] ACPI handle has no context!
[ 952.537474] ACPI: PCI interrupt for device 0000:00:0a.0 disabled
[ 952.537495] ACPI handle has no context!
[ 956.857085] Back to C!
Are you sure that is standby? Looks like suspend-to-RAM to me.
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
On Mon, August 6, 2007 11:44, Pavel Machek wrote:
Hi!
quoted
quoted
00:0a.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet
Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
Memory at e3020000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b000 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
00:0a.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet
Controller (Copper) (rev 01)
Subsystem: Intel Corp.: Unknown device 1012
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 12
Memory at e3000000 (64-bit, non-prefetchable) [size=128K]
I/O ports at b400 [size=64]
Capabilities: [dc] Power Management version 2
Capabilities: [e4] PCI-X non-bridge device.
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
[ 950.132046] Stopping tasks ... done.
[ 950.459794] Suspending console(s)
[ 951.776277] pnp: Device 00:0c disabled.
[ 951.776673] pnp: Device 00:0a disabled.
[ 951.776984] pnp: Device 00:09 disabled.
[ 951.777306] pnp: Device 00:08 disabled.
[ 951.777786] ACPI: PCI interrupt for device 0000:00:11.5 disabled
[ 951.995359] ACPI: PCI interrupt for device 0000:00:11.3 disabled
[ 952.006094] ACPI: PCI interrupt for device 0000:00:11.2 disabled
[ 952.022243] ACPI handle has no context!
[ 952.033068] ACPI: PCI interrupt for device 0000:00:0c.2 disabled
[ 952.044086] ACPI: PCI interrupt for device 0000:00:0c.1 disabled
[ 952.055083] ACPI: PCI interrupt for device 0000:00:0c.0 disabled
[ 952.282211] ACPI: PCI interrupt for device 0000:00:0a.1 disabled
[ 952.282221] ACPI handle has no context!
[ 952.537474] ACPI: PCI interrupt for device 0000:00:0a.0 disabled
[ 952.537495] ACPI handle has no context!
[ 956.857085] Back to C!
Are you sure that is standby? Looks like suspend-to-RAM to me.
It's S1 (power-on suspend/standby), my BIOS/motherboard doesn't support S2 or S3.
--
Simon Arlott