[PATCH v6 1/7] QE: Add IC, SI and SIRAM document to device tree bindings.

@@ -69,6 +69,58 @@ Example:
 	};
      };
 
+* Interrupt Controller (IC)
+
+Required properties:
+- compatible : should be "fsl,qe-ic".
+- reg : Address range of IC register set.
+- interrupts : interrupts generated by the device.
+- interrupt-controller : this device is a interrupt controller.
+
+Example:
+
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <95 2 0 0  94 2 0 0>;
+	};
+
+* Serial Interface Block (SI)
+
+The SI manages the routing of eight TDM lines to the QE block serial drivers
+, the MCC and the UCCs, for receive and transmit.
+
+Required properties:
+- compatible : must be "fsl,<chip>-qe-si". For t1040, must contain
+  "fsl,t1040-qe-si".
+- reg : Address range of SI register set.
+
+Example:
+
+	si1: si@700 {
+		compatible = "fsl,t1040-qe-si";
+		reg = <0x700 0x80>;
+	};
+
+* Serial Interface Block RAM(SIRAM)
+
+store the routing entries of SI
+
+Required properties:
+- compatible : should be "fsl,<chip>-qe-siram". For t1040, must contain
+  "fsl,t1040-qe-siram".
+- reg : Address range of SI RAM.
+
+Example:
+
+	siram1: siram@1000 {
+		compatible = "fsl,t1040-qe-siram";
+		reg = <0x1000 0x800>;
+	};
+
 * QE Firmware Node
 
 This node defines a firmware binary that is embedded in the device tree, for

@@ -41,3 +41,84 @@ Example:
 		fsl,mdio-pin = <12>;
 		fsl,mdc-pin = <13>;
 	};
+
+* HDLC
+
+Currently defined compatibles:
+- fsl,ucc-hdlc
+
+Properties for fsl,ucc-hdlc:
+- rx-clock-name
+- tx-clock-name
+	Usage: required
+	Value type: <string>
+	Definition : Must be "brg1"-"brg16" for internal clock source,
+		     Must be "clk1"-"clk24" for external clock source.
+
+- fsl,tdm-interface
+	Usage: optional
+	Value type: <empty>
+	Definition : Specify that hdlc is based on tdm-interface
+
+The property below is dependent on fsl,tdm-interface:
+- fsl,rx-sync-clock
+	Usage: required
+	Value type: <string>
+	Definition : Must be "none", "rsync_pin", "brg9-11" and "brg13-15".
+
+- fsl,tx-sync-clock
+	Usage: required
+	Value type: <string>
+	Definition : Must be "none", "tsync_pin", "brg9-11" and "brg13-15".
+
+- fsl,tdm-framer-type
+	Usage: required for tdm interface
+	Value type: <string>
+	Definition : "e1" or "t1".Now e1 and t1 are used, other framer types
+		     are not supported.
+
+- fsl,tdm-id
+	Usage: required for tdm interface
+	Value type: <u32>
+	Definition : number of TDM ID
+
+- fsl,tx-timeslot-mask
+- fsl,rx-timeslot-mask
+	Usage: required for tdm interface
+	Value type: <u32>
+	Definition : time slot mask for TDM operation. Indicates which time
+		     slots used for transmitting and receiving.
+
+- fsl,siram-entry-id
+	Usage: required for tdm interface
+	Value type: <u32>
+	Definition : Must be 0,2,4...64. the number of TDM entry.
+
+- fsl,tdm-internal-loopback
+	usage: optional for tdm interface
+	value type: <empty>
+	Definition : Internal loopback connecting on TDM layer.
+
+Example for tdm interface:
+
+	ucc@2000 {
+		compatible = "fsl,ucc-hdlc";
+		rx-clock-name = "clk8";
+		tx-clock-name = "clk9";
+		fsl,rx-sync-clock = "rsync_pin";
+		fsl,tx-sync-clock = "tsync_pin";
+		fsl,tx-timeslot-mask = <0xfffffffe>;
+		fsl,rx-timeslot-mask = <0xfffffffe>;
+		fsl,tdm-framer-type = "e1";
+		fsl,tdm-id = <0>;
+		fsl,siram-entry-id = <0>;
+		fsl,tdm-interface;
+	};
+
+Example for hdlc without tdm interface:
+
+	ucc@2000 {
+		compatible = "fsl,ucc-hdlc";
+		rx-clock-name = "brg1";
+		tx-clock-name = "brg1";
+	};