On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson
[off-list ref] wrote:
clock-frequency = <0x1e84800>; //<0>; // From boot loader
interrupts = <2 8 0 2 9 0 2 10 0>;
interrupt-parent = <&mpc5200_pic>;
bus-range = <0 0>;
ranges = <0x02000000 0 0x50000000 0x50000000 0 0x10000000
0x01000000 0 0x00000000 0x60000000 0 0x01000000>;
};
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all mapped
to zero.
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hmmm. Your ranges property looks okay to me. The MPC5200 setup code
may be doing the wrong thing. Turn on debug at the top of
arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel
output.
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
When enabling the debug-printouts, it came to me that I forgot to
mention something kind of important. Using the standard mpc52xx_pci.c,
even the memory resources are mapped to zero.
After disabling this code block, the memory regions are mapped out
fine (but still no IO):
static void
mpc52xx_pci_fixup_resources(struct pci_dev *dev)
{
int i;
pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n",
dev->vendor, dev->device);
/* We don't rely on boot loader for PCI and resets all
devices */
for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) {
struct resource *res =3D &dev->resource[i];
if (res->end > res->start) { /* Only valid resources */
res->end -=3D res->start;
res->start =3D 0;
res->flags |=3D IORESOURCE_UNSET;
}
}
What is the purpose of this code? Since all resources are reset here,
where are they inteded to be re-allocated?
Here is the bootlog with the aforementioned code enabled:
reading cuImage.lite5200b
1833699 bytes read
## Booting kernel from Legacy Image at 00201400 ...
Image Name: Linux-2.6.28
Created: 2009-02-05 6:54:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1833635 Bytes =3D 1.7 MB
Load Address: 00400000
Entry Point: 004005a0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
[ 0.000000] Using lite5200 machine description
[ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc
version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET
2009
[ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00
[ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges:
[ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> 0x00000000500=
00000
[ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> 0x00000000000=
00000
[ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00)
[ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff, .fl=
ags=3D200}
[ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100}
.io_base_phys=3D0x60000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00004000
[ 0.000000] Normal 0x00004000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/dev/sd=
a2 rw
[ 0.000000] MPC52xx PIC is up and running!
[ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[ 0.000000] clocksource: timebase mult[7d00000] shift[22] registered
[ 0.000263] console [ttyPSC0] enabled
[ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes=
)
[ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.147433] Memory: 60844k/65536k available (3704k kernel code,
4624k reserved, 156k data, 117k bss, 180k init)
[ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObjects=
=3D0,
CPUs=3D1, Nodes=3D1
[ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744)
[ 0.236265] Mount-cache hash table entries: 512
[ 0.245719] net_namespace: 288 bytes
[ 0.250237] NET: Registered protocol family 16
[ 0.284887] PCI: Probing PCI hardware
[ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809
[ 0.294799] PCI:0000:00:17.0 Resource 0
0000000050400000-00000000507fffff [21208] fixup...
[ 0.303180] PCI:0000:00:17.0 0000000050400000-00000000507ffff=
f
[ 0.309998] PCI:0000:00:17.0 Resource 1
0000000050800000-0000000050ffffff [20200] fixup...
[ 0.318262] PCI:0000:00:17.0 0000000050800000-0000000050fffff=
f
[ 0.325062] PCI:0000:00:17.0 Resource 2
0000000060000000-000000006000000f [20101] fixup...
[ 0.333326] PCI:0000:00:17.0 0000000060000000-000000006000000=
f
[ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.345242] PCI:0000:00:18.0 Resource 0
0000000051000000-00000000513fffff [21208] fixup...
[ 0.353519] PCI:0000:00:18.0 0000000051000000-00000000513ffff=
f
[ 0.360319] PCI:0000:00:18.0 Resource 1
0000000051800000-0000000051ffffff [20200] fixup...
[ 0.368583] PCI:0000:00:18.0 0000000051800000-0000000051fffff=
f
[ 0.375383] PCI:0000:00:18.0 Resource 2
0000000060000010-000000006000001f [20101] fixup...
[ 0.383647] PCI:0000:00:18.0 0000000060000010-000000006000001=
f
[ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.395549] PCI:0000:00:19.0 Resource 0
0000000052000000-00000000523fffff [21208] fixup...
[ 0.403826] PCI:0000:00:19.0 0000000052000000-00000000523ffff=
f
[ 0.410626] PCI:0000:00:19.0 Resource 1
0000000052800000-0000000052ffffff [20200] fixup...
[ 0.418889] PCI:0000:00:19.0 0000000052800000-0000000052fffff=
f
[ 0.425690] PCI:0000:00:19.0 Resource 2
0000000060000020-000000006000002f [20101] fixup...
[ 0.433954] PCI:0000:00:19.0 0000000060000020-000000006000002=
f
[ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.445854] PCI:0000:00:1a.0 Resource 0
0000000053000000-00000000533fffff [21208] fixup...
[ 0.454130] PCI:0000:00:1a.0 0000000053000000-00000000533ffff=
f
[ 0.460930] PCI:0000:00:1a.0 Resource 1
0000000053800000-0000000053ffffff [20200] fixup...
[ 0.469194] PCI:0000:00:1a.0 0000000053800000-0000000053fffff=
f
[ 0.475994] PCI:0000:00:1a.0 Resource 2
0000000060000030-000000006000003f [20101] fixup...
[ 0.484258] PCI:0000:00:1a.0 0000000060000030-000000006000003=
f
[ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.495999] PCI: Fixup bus 0 (PHB)
[ 0.499383] PCI: device 0000:00:16.0 OF node: <none>
[ 0.504371] PCI: device 0000:00:17.0 OF node: <none>
[ 0.509363] PCI: device 0000:00:18.0 OF node: <none>
[ 0.514354] PCI: device 0000:00:19.0 OF node: <none>
[ 0.519345] PCI: device 0000:00:1a.0 OF node: <none>
[ 0.524332] Try to map irq for 0000:00:16.0...
[ 0.528808] Try to map irq for 0000:00:17.0...
[ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.543389] -> mapped to linux irq 65
[ 0.547117] Try to map irq for 0000:00:18.0...
[ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.561629] -> mapped to linux irq 65
[ 0.565353] Try to map irq for 0000:00:19.0...
[ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.579863] -> mapped to linux irq 65
[ 0.583587] Try to map irq for 0000:00:1a.0...
[ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.598103] -> mapped to linux irq 65
[ 0.605144] PCI: PHB (bus 0) bridge rsrc 0:
0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO)
[ 0.615266] PCI: PHB (bus 0) bridge rsrc 1:
0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem)
[ 0.625539] PCI: Assigning unassigned resouces...
[ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff]
[ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff]
[ 0.640909] DMA: MPC52xx BestComm driver
[ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok !
[ 0.678739] SCSI subsystem initialized
[ 0.709498] NET: Registered protocol family 2
[ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096 byte=
s)
[ 0.762429] TCP established hash table entries: 2048 (order: 2, 16384 by=
tes)
[ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.776224] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.782604] TCP reno registered
[ 0.795054] NET: Registered protocol family 1
[ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc.
[ 0.855699] msgmni has been set to 118
[ 0.861227] alg: No test for stdrng (krng)
[ 0.865651] io scheduler noop registered
[ 0.869658] io scheduler anticipatory registered (default)
[ 0.875224] io scheduler deadline registered
[ 0.879838] io scheduler cfq registered
[ 1.442231] Generic RTC Driver v1.07
[ 1.447145] Serial: MPC52xx PSC UART driver
[ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 130)
is a MPC52xx PSC
[ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 131)
is a MPC52xx PSC
[ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 139)
is a MPC52xx PSC
[ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 140)
is a MPC52xx PSC
[ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 132)
is a MPC52xx PSC
[ 1.521689] brd: module loaded
[ 1.535886] loop: module loaded
[ 1.544328] mpc52xx MII bus: probed
[ 1.550220] net eth0: Using PHY at MDIO address 0
[ 1.556124] Driver 'sd' needs updating - please use bus_type methods
[ 1.563224] ata: MPC52xx IDE/ATA libata driver
[ 1.568729] scsi0 : mpc52xx_ata
[ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135
[ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66
[ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA
[ 1.775156] ata1.00: configured for UDMA/33
[ 1.803154] ata1.00: configured for UDMA/33
[ 1.807423] ata1: EH complete
[ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND
2007 PQ: 0 ANSI: 5
[ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.829333] sd 0:0:0:0: [sda] Write Protect is off
[ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.852841] sd 0:0:0:0: [sda] Write Protect is off
[ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.867450] sda: sda1 sda2
[ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit bank
[ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.902529] fc000000.flash: CFI does not contain boot bank
location. Assuming top.
[ 1.910147] number of CFI chips: 1
[ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to
code brokenness.
[ 1.922009] RedBoot partition parsing not available
[ 1.926998] Creating 4 MTD partitions on "fc000000.flash":
[ 1.932547] 0x00000000-0x00500000 : "u-boot"
[ 1.940601] 0x00500000-0x01000000 : "kernel"
[ 1.948071] 0x01000000-0x02000000 : "rootfs"
[ 1.955601] 0x02000000-0x03000000 : "application"
[ 1.964240] i2c /dev entries driver
[ 1.975775] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
[ 1.983814] ASoC version 0.13.2
[ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device
[ 2.040451] registering ASoC codec driver:
/soc5200@f0000000/i2c@3d00/codec@1a
[ 2.049539] ALSA device list:
[ 2.052591] No soundcards found.
[ 2.057430] TCP cubic registered
[ 2.060765] NET: Registered protocol family 17
[ 2.066886] RPC: Registered udp transport module.
[ 2.071683] RPC: Registered tcp transport module.
[ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck
is recommended
[ 2.094828] VFS: Mounted root (ext2 filesystem).
[ 2.099690] Freeing unused kernel memory: 180k init
On Wed, Feb 4, 2009 at 18:54, Grant Likely [off-list ref] wrot=
e:On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
clock-frequency =3D <0x1e84800>; //<0>; // From boot load=
er
quoted
interrupts =3D <2 8 0 2 9 0 2 10 0>;
interrupt-parent =3D <&mpc5200_pic>;
bus-range =3D <0 0>;
ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x1000000=
0
quoted
0x01000000 0 0x00000000 0x60000000 0 0x01000000>=
;
quoted
};
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all mapp=
ed
quoted
to zero.
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hmmm. Your ranges property looks okay to me. The MPC5200 setup code
may be doing the wrong thing. Turn on debug at the top of
arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel
output.
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--=20
H=E4lsningar/Regards
Tobias Knutsson
On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson
[off-list ref] wrote:
When enabling the debug-printouts, it came to me that I forgot to
mention something kind of important. Using the standard mpc52xx_pci.c,
even the memory resources are mapped to zero.
After disabling this code block, the memory regions are mapped out
fine (but still no IO):
Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c,
and post the results.
When this code is disabled then you're just getting the leftovers from
U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own
scan and its own allocation of memory/IO address space and this code
is needed to make sure that happens.
g.
static void
mpc52xx_pci_fixup_resources(struct pci_dev *dev)
{
int i;
pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n",
dev->vendor, dev->device);
/* We don't rely on boot loader for PCI and resets all
devices */
for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) {
struct resource *res =3D &dev->resource[i];
if (res->end > res->start) { /* Only valid resources */
res->end -=3D res->start;
res->start =3D 0;
res->flags |=3D IORESOURCE_UNSET;
}
}
What is the purpose of this code? Since all resources are reset here,
where are they inteded to be re-allocated?
Here is the bootlog with the aforementioned code enabled:
reading cuImage.lite5200b
1833699 bytes read
## Booting kernel from Legacy Image at 00201400 ...
Image Name: Linux-2.6.28
Created: 2009-02-05 6:54:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1833635 Bytes =3D 1.7 MB
Load Address: 00400000
Entry Point: 004005a0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
[ 0.000000] Using lite5200 machine description
[ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc
version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET
2009
[ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00
[ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges:
[ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> 0x000000005=
0000000
[ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> 0x000000000=
0000000
[ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00)
[ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff, .=
flags=3D200}
[ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100}
.io_base_phys=3D0x60000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00004000
[ 0.000000] Normal 0x00004000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/dev/=
sda2 rw
[ 0.000000] MPC52xx PIC is up and running!
[ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[ 0.000000] clocksource: timebase mult[7d00000] shift[22] registered
[ 0.000263] console [ttyPSC0] enabled
[ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768 byt=
es)
[ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384 byte=
s)
[ 0.147433] Memory: 60844k/65536k available (3704k kernel code,
4624k reserved, 156k data, 117k bss, 180k init)
[ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObjects=
=3D0,
CPUs=3D1, Nodes=3D1
[ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744)
[ 0.236265] Mount-cache hash table entries: 512
[ 0.245719] net_namespace: 288 bytes
[ 0.250237] NET: Registered protocol family 16
[ 0.284887] PCI: Probing PCI hardware
[ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809
[ 0.294799] PCI:0000:00:17.0 Resource 0
0000000050400000-00000000507fffff [21208] fixup...
[ 0.303180] PCI:0000:00:17.0 0000000050400000-00000000507ff=
fff
[ 0.309998] PCI:0000:00:17.0 Resource 1
0000000050800000-0000000050ffffff [20200] fixup...
[ 0.318262] PCI:0000:00:17.0 0000000050800000-0000000050fff=
fff
[ 0.325062] PCI:0000:00:17.0 Resource 2
0000000060000000-000000006000000f [20101] fixup...
[ 0.333326] PCI:0000:00:17.0 0000000060000000-0000000060000=
00f
[ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.345242] PCI:0000:00:18.0 Resource 0
0000000051000000-00000000513fffff [21208] fixup...
[ 0.353519] PCI:0000:00:18.0 0000000051000000-00000000513ff=
fff
[ 0.360319] PCI:0000:00:18.0 Resource 1
0000000051800000-0000000051ffffff [20200] fixup...
[ 0.368583] PCI:0000:00:18.0 0000000051800000-0000000051fff=
fff
[ 0.375383] PCI:0000:00:18.0 Resource 2
0000000060000010-000000006000001f [20101] fixup...
[ 0.383647] PCI:0000:00:18.0 0000000060000010-0000000060000=
01f
[ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.395549] PCI:0000:00:19.0 Resource 0
0000000052000000-00000000523fffff [21208] fixup...
[ 0.403826] PCI:0000:00:19.0 0000000052000000-00000000523ff=
fff
[ 0.410626] PCI:0000:00:19.0 Resource 1
0000000052800000-0000000052ffffff [20200] fixup...
[ 0.418889] PCI:0000:00:19.0 0000000052800000-0000000052fff=
fff
[ 0.425690] PCI:0000:00:19.0 Resource 2
0000000060000020-000000006000002f [20101] fixup...
[ 0.433954] PCI:0000:00:19.0 0000000060000020-0000000060000=
02f
[ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.445854] PCI:0000:00:1a.0 Resource 0
0000000053000000-00000000533fffff [21208] fixup...
[ 0.454130] PCI:0000:00:1a.0 0000000053000000-00000000533ff=
fff
[ 0.460930] PCI:0000:00:1a.0 Resource 1
0000000053800000-0000000053ffffff [20200] fixup...
[ 0.469194] PCI:0000:00:1a.0 0000000053800000-0000000053fff=
fff
[ 0.475994] PCI:0000:00:1a.0 Resource 2
0000000060000030-000000006000003f [20101] fixup...
[ 0.484258] PCI:0000:00:1a.0 0000000060000030-0000000060000=
03f
[ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.495999] PCI: Fixup bus 0 (PHB)
[ 0.499383] PCI: device 0000:00:16.0 OF node: <none>
[ 0.504371] PCI: device 0000:00:17.0 OF node: <none>
[ 0.509363] PCI: device 0000:00:18.0 OF node: <none>
[ 0.514354] PCI: device 0000:00:19.0 OF node: <none>
[ 0.519345] PCI: device 0000:00:1a.0 OF node: <none>
[ 0.524332] Try to map irq for 0000:00:16.0...
[ 0.528808] Try to map irq for 0000:00:17.0...
[ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.543389] -> mapped to linux irq 65
[ 0.547117] Try to map irq for 0000:00:18.0...
[ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.561629] -> mapped to linux irq 65
[ 0.565353] Try to map irq for 0000:00:19.0...
[ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.579863] -> mapped to linux irq 65
[ 0.583587] Try to map irq for 0000:00:1a.0...
[ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.598103] -> mapped to linux irq 65
[ 0.605144] PCI: PHB (bus 0) bridge rsrc 0:
0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO)
[ 0.615266] PCI: PHB (bus 0) bridge rsrc 1:
0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem)
[ 0.625539] PCI: Assigning unassigned resouces...
[ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff]
[ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff]
[ 0.640909] DMA: MPC52xx BestComm driver
[ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok !
[ 0.678739] SCSI subsystem initialized
[ 0.709498] NET: Registered protocol family 2
[ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096 by=
tes)
[ 0.762429] TCP established hash table entries: 2048 (order: 2, 16384 =
bytes)
[ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.776224] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.782604] TCP reno registered
[ 0.795054] NET: Registered protocol family 1
[ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc.
[ 0.855699] msgmni has been set to 118
[ 0.861227] alg: No test for stdrng (krng)
[ 0.865651] io scheduler noop registered
[ 0.869658] io scheduler anticipatory registered (default)
[ 0.875224] io scheduler deadline registered
[ 0.879838] io scheduler cfq registered
[ 1.442231] Generic RTC Driver v1.07
[ 1.447145] Serial: MPC52xx PSC UART driver
[ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 130)
is a MPC52xx PSC
[ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 131)
is a MPC52xx PSC
[ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 139)
is a MPC52xx PSC
[ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 140)
is a MPC52xx PSC
[ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 132)
is a MPC52xx PSC
[ 1.521689] brd: module loaded
[ 1.535886] loop: module loaded
[ 1.544328] mpc52xx MII bus: probed
[ 1.550220] net eth0: Using PHY at MDIO address 0
[ 1.556124] Driver 'sd' needs updating - please use bus_type methods
[ 1.563224] ata: MPC52xx IDE/ATA libata driver
[ 1.568729] scsi0 : mpc52xx_ata
[ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135
[ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66
[ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA
[ 1.775156] ata1.00: configured for UDMA/33
[ 1.803154] ata1.00: configured for UDMA/33
[ 1.807423] ata1: EH complete
[ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND
2007 PQ: 0 ANSI: 5
[ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.829333] sd 0:0:0:0: [sda] Write Protect is off
[ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.852841] sd 0:0:0:0: [sda] Write Protect is off
[ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.867450] sda: sda1 sda2
[ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit bank
[ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.902529] fc000000.flash: CFI does not contain boot bank
location. Assuming top.
[ 1.910147] number of CFI chips: 1
[ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to
code brokenness.
[ 1.922009] RedBoot partition parsing not available
[ 1.926998] Creating 4 MTD partitions on "fc000000.flash":
[ 1.932547] 0x00000000-0x00500000 : "u-boot"
[ 1.940601] 0x00500000-0x01000000 : "kernel"
[ 1.948071] 0x01000000-0x02000000 : "rootfs"
[ 1.955601] 0x02000000-0x03000000 : "application"
[ 1.964240] i2c /dev entries driver
[ 1.975775] Advanced Linux Sound Architecture Driver Version 1.0.18rc3=
.
[ 1.983814] ASoC version 0.13.2
[ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device
[ 2.040451] registering ASoC codec driver:
/soc5200@f0000000/i2c@3d00/codec@1a
[ 2.049539] ALSA device list:
[ 2.052591] No soundcards found.
[ 2.057430] TCP cubic registered
[ 2.060765] NET: Registered protocol family 17
[ 2.066886] RPC: Registered udp transport module.
[ 2.071683] RPC: Registered tcp transport module.
[ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck
is recommended
[ 2.094828] VFS: Mounted root (ext2 filesystem).
[ 2.099690] Freeing unused kernel memory: 180k init
On Wed, Feb 4, 2009 at 18:54, Grant Likely [off-list ref] wr=
ote:
quoted
On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
clock-frequency =3D <0x1e84800>; //<0>; // From boot loa=
der
quoted
quoted
interrupts =3D <2 8 0 2 9 0 2 10 0>;
interrupt-parent =3D <&mpc5200_pic>;
bus-range =3D <0 0>;
ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x100000=
00
quoted
quoted
0x01000000 0 0x00000000 0x60000000 0 0x01000000=
;
quoted
quoted
};
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all map=
ped
quoted
quoted
to zero.
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hmmm. Your ranges property looks okay to me. The MPC5200 setup code
may be doing the wrong thing. Turn on debug at the top of
arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel
output.
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--
H=E4lsningar/Regards
Tobias Knutsson
--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
Hi,
That is exactly what the bootlog shows. Debug output on in both =20
mpc52xx_pci.c and in pci-common.c. And the discussed code section =20
enabled.
H=C3=A4lsningar / Regards
Tobias Knutsson
On 5 feb 2009, at 17.44, Grant Likely [off-list ref] wrote:
On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
When enabling the debug-printouts, it came to me that I forgot to
mention something kind of important. Using the standard =20
mpc52xx_pci.c,
even the memory resources are mapped to zero.
After disabling this code block, the memory regions are mapped out
fine (but still no IO):
Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c,
and post the results.
When this code is disabled then you're just getting the leftovers from
U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own
scan and its own allocation of memory/IO address space and this code
is needed to make sure that happens.
g.
quoted
static void
mpc52xx_pci_fixup_resources(struct pci_dev *dev)
{
int i;
pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n",
dev->vendor, dev->device);
/* We don't rely on boot loader for PCI and resets all
devices */
for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) {
struct resource *res =3D &dev->resource[i];
if (res->end > res->start) { /* Only valid =20
resources */
res->end -=3D res->start;
res->start =3D 0;
res->flags |=3D IORESOURCE_UNSET;
}
}
What is the purpose of this code? Since all resources are reset here,
where are they inteded to be re-allocated?
Here is the bootlog with the aforementioned code enabled:
reading cuImage.lite5200b
1833699 bytes read
## Booting kernel from Legacy Image at 00201400 ...
Image Name: Linux-2.6.28
Created: 2009-02-05 6:54:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1833635 Bytes =3D 1.7 MB
Load Address: 00400000
Entry Point: 004005a0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
[ 0.000000] Using lite5200 machine description
[ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc
version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET
2009
[ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00
[ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges:
[ 0.000000] MEM 0x0000000050000000..0x000000005fffffff -> =20
0x0000000050000000
[ 0.000000] IO 0x0000000060000000..0x0000000060ffffff -> =20
0x0000000000000000
[ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00)
[ 0.000000] mem_resource[0] =3D =20
{.start=3D50000000, .end=3D5fffffff, .flags=3D200}
[ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100}
.io_base_phys=3D0x60000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00004000
[ 0.000000] Normal 0x00004000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/=20=
quoted
dev/sda2 rw
[ 0.000000] MPC52xx PIC is up and running!
[ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[ 0.000000] clocksource: timebase mult[7d00000] shift[22] =20
registered
[ 0.000263] console [ttyPSC0] enabled
[ 0.121690] Dentry cache hash table entries: 8192 (order: 3, =20
32768 bytes)
[ 0.129012] Inode-cache hash table entries: 4096 (order: 2, =20
16384 bytes)
[ 0.147433] Memory: 60844k/65536k available (3704k kernel code,
4624k reserved, 156k data, 117k bss, 180k init)
[ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, =20
MinObjects=3D0,
CPUs=3D1, Nodes=3D1
[ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744)
[ 0.236265] Mount-cache hash table entries: 512
[ 0.245719] net_namespace: 288 bytes
[ 0.250237] NET: Registered protocol family 16
[ 0.284887] PCI: Probing PCI hardware
[ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809
[ 0.294799] PCI:0000:00:17.0 Resource 0
0000000050400000-00000000507fffff [21208] fixup...
[ 0.303180] PCI:0000:00:17.0 =20
0000000050400000-00000000507fffff
[ 0.309998] PCI:0000:00:17.0 Resource 1
0000000050800000-0000000050ffffff [20200] fixup...
[ 0.318262] PCI:0000:00:17.0 =20
0000000050800000-0000000050ffffff
[ 0.325062] PCI:0000:00:17.0 Resource 2
0000000060000000-000000006000000f [20101] fixup...
[ 0.333326] PCI:0000:00:17.0 =20
0000000060000000-000000006000000f
[ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.345242] PCI:0000:00:18.0 Resource 0
0000000051000000-00000000513fffff [21208] fixup...
[ 0.353519] PCI:0000:00:18.0 =20
0000000051000000-00000000513fffff
[ 0.360319] PCI:0000:00:18.0 Resource 1
0000000051800000-0000000051ffffff [20200] fixup...
[ 0.368583] PCI:0000:00:18.0 =20
0000000051800000-0000000051ffffff
[ 0.375383] PCI:0000:00:18.0 Resource 2
0000000060000010-000000006000001f [20101] fixup...
[ 0.383647] PCI:0000:00:18.0 =20
0000000060000010-000000006000001f
[ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.395549] PCI:0000:00:19.0 Resource 0
0000000052000000-00000000523fffff [21208] fixup...
[ 0.403826] PCI:0000:00:19.0 =20
0000000052000000-00000000523fffff
[ 0.410626] PCI:0000:00:19.0 Resource 1
0000000052800000-0000000052ffffff [20200] fixup...
[ 0.418889] PCI:0000:00:19.0 =20
0000000052800000-0000000052ffffff
[ 0.425690] PCI:0000:00:19.0 Resource 2
0000000060000020-000000006000002f [20101] fixup...
[ 0.433954] PCI:0000:00:19.0 =20
0000000060000020-000000006000002f
[ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.445854] PCI:0000:00:1a.0 Resource 0
0000000053000000-00000000533fffff [21208] fixup...
[ 0.454130] PCI:0000:00:1a.0 =20
0000000053000000-00000000533fffff
[ 0.460930] PCI:0000:00:1a.0 Resource 1
0000000053800000-0000000053ffffff [20200] fixup...
[ 0.469194] PCI:0000:00:1a.0 =20
0000000053800000-0000000053ffffff
[ 0.475994] PCI:0000:00:1a.0 Resource 2
0000000060000030-000000006000003f [20101] fixup...
[ 0.484258] PCI:0000:00:1a.0 =20
0000000060000030-000000006000003f
[ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.495999] PCI: Fixup bus 0 (PHB)
[ 0.499383] PCI: device 0000:00:16.0 OF node: <none>
[ 0.504371] PCI: device 0000:00:17.0 OF node: <none>
[ 0.509363] PCI: device 0000:00:18.0 OF node: <none>
[ 0.514354] PCI: device 0000:00:19.0 OF node: <none>
[ 0.519345] PCI: device 0000:00:1a.0 OF node: <none>
[ 0.524332] Try to map irq for 0000:00:16.0...
[ 0.528808] Try to map irq for 0000:00:17.0...
[ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) =20=
quoted
on
/soc5200@f0000000/interrupt-controller@500
[ 0.543389] -> mapped to linux irq 65
[ 0.547117] Try to map irq for 0000:00:18.0...
[ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) =20=
quoted
on
/soc5200@f0000000/interrupt-controller@500
[ 0.561629] -> mapped to linux irq 65
[ 0.565353] Try to map irq for 0000:00:19.0...
[ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) =20=
quoted
on
/soc5200@f0000000/interrupt-controller@500
[ 0.579863] -> mapped to linux irq 65
[ 0.583587] Try to map irq for 0000:00:1a.0...
[ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) =20=
quoted
on
/soc5200@f0000000/interrupt-controller@500
[ 0.598103] -> mapped to linux irq 65
[ 0.605144] PCI: PHB (bus 0) bridge rsrc 0:
0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO)
[ 0.615266] PCI: PHB (bus 0) bridge rsrc 1:
0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem)
[ 0.625539] PCI: Assigning unassigned resouces...
[ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff]
[ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff]
[ 0.640909] DMA: MPC52xx BestComm driver
[ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok !
[ 0.678739] SCSI subsystem initialized
[ 0.709498] NET: Registered protocol family 2
[ 0.754980] IP route cache hash table entries: 1024 (order: 0, =20
4096 bytes)
[ 0.762429] TCP established hash table entries: 2048 (order: 2, =20=
quoted
16384 bytes)
[ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 =20
bytes)
[ 0.776224] TCP: Hash tables configured (established 2048 bind =20
2048)
[ 0.782604] TCP reno registered
[ 0.795054] NET: Registered protocol family 1
[ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc.
[ 0.855699] msgmni has been set to 118
[ 0.861227] alg: No test for stdrng (krng)
[ 0.865651] io scheduler noop registered
[ 0.869658] io scheduler anticipatory registered (default)
[ 0.875224] io scheduler deadline registered
[ 0.879838] io scheduler cfq registered
[ 1.442231] Generic RTC Driver v1.07
[ 1.447145] Serial: MPC52xx PSC UART driver
[ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D =20=
quoted
130)
is a MPC52xx PSC
[ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D =20=
quoted
131)
is a MPC52xx PSC
[ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D =20=
quoted
139)
is a MPC52xx PSC
[ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D =20=
quoted
140)
is a MPC52xx PSC
[ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D =20=
quoted
132)
is a MPC52xx PSC
[ 1.521689] brd: module loaded
[ 1.535886] loop: module loaded
[ 1.544328] mpc52xx MII bus: probed
[ 1.550220] net eth0: Using PHY at MDIO address 0
[ 1.556124] Driver 'sd' needs updating - please use bus_type =20
methods
[ 1.563224] ata: MPC52xx IDE/ATA libata driver
[ 1.568729] scsi0 : mpc52xx_ata
[ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135
[ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66
[ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA
[ 1.775156] ata1.00: configured for UDMA/33
[ 1.803154] ata1.00: configured for UDMA/33
[ 1.807423] ata1: EH complete
[ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND
2007 PQ: 0 ANSI: 5
[ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.829333] sd 0:0:0:0: [sda] Write Protect is off
[ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.852841] sd 0:0:0:0: [sda] Write Protect is off
[ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.867450] sda: sda1 sda2
[ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit =20=
quoted
bank
[ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.902529] fc000000.flash: CFI does not contain boot bank
location. Assuming top.
[ 1.910147] number of CFI chips: 1
[ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due =20=
quoted
to
code brokenness.
[ 1.922009] RedBoot partition parsing not available
[ 1.926998] Creating 4 MTD partitions on "fc000000.flash":
[ 1.932547] 0x00000000-0x00500000 : "u-boot"
[ 1.940601] 0x00500000-0x01000000 : "kernel"
[ 1.948071] 0x01000000-0x02000000 : "rootfs"
[ 1.955601] 0x02000000-0x03000000 : "application"
[ 1.964240] i2c /dev entries driver
[ 1.975775] Advanced Linux Sound Architecture Driver Version =20
1.0.18rc3.
[ 1.983814] ASoC version 0.13.2
[ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device
[ 2.040451] registering ASoC codec driver:
/soc5200@f0000000/i2c@3d00/codec@1a
[ 2.049539] ALSA device list:
[ 2.052591] No soundcards found.
[ 2.057430] TCP cubic registered
[ 2.060765] NET: Registered protocol family 17
[ 2.066886] RPC: Registered udp transport module.
[ 2.071683] RPC: Registered tcp transport module.
[ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck
is recommended
[ 2.094828] VFS: Mounted root (ext2 filesystem).
[ 2.099690] Freeing unused kernel memory: 180k init
On Wed, Feb 4, 2009 at 18:54, Grant Likely =20
[off-list ref] wrote:
quoted
On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
clock-frequency =3D <0x1e84800>; //<0>; // =46rom =
boot =20
quoted
quoted
quoted
loader
interrupts =3D <2 8 0 2 9 0 2 10 0>;
interrupt-parent =3D <&mpc5200_pic>;
bus-range =3D <0 0>;
ranges =3D <0x02000000 0 0x50000000 0x50000000 0 =20
0x10000000
0x01000000 0 0x00000000 0x60000000 0 =20
0x01000000>;
};
The cards' memory regions are mapped out fine to different =20
addresses
in the 0x50000000-0x60000000 range. However, the IO regions are =20
all mapped
to zero.
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hmmm. Your ranges property looks okay to me. The MPC5200 setup =20
code
may be doing the wrong thing. Turn on debug at the top of
arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel
output.
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--
H=C3=A4lsningar/Regards
Tobias Knutsson
--=20
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
Ok, I have had a breakthrough. I was trying to find out where the
resources were supposed to be allocated and that was when i found this
section of code in pbus_assign_resources_sorted() in
drivers/pci/setup-bus.c:
/* Don't touch classless devices or host bridges or ioapics. */
if (class =3D=3D PCI_CLASS_NOT_DEFINED ||
class =3D=3D PCI_CLASS_BRIDGE_HOST)
continue;
After that i took a quick look at the PCI-info reported by u-boot.
Sure enough, all boards were reported having class 0. At first i tried
to write a different class type, but as i suspected, the register
seems to be read-only. Therefore I simply commented out the first part
of the if-statement and now the resources seems to get allocated
properly.
However, I do realize that this is not the proper way of solving this
issue. Any ideas on how to fix it without modifying any kernel code?
On Thu, Feb 5, 2009 at 21:03, Tobias Knutsson [off-list ref] w=
rote:
Hi,
That is exactly what the bootlog shows. Debug output on in both
mpc52xx_pci.c and in pci-common.c. And the discussed code section enabled=
.
H=E4lsningar / Regards
Tobias Knutsson
On 5 feb 2009, at 17.44, Grant Likely [off-list ref] wrote:
quoted
On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
When enabling the debug-printouts, it came to me that I forgot to
mention something kind of important. Using the standard mpc52xx_pci.c,
even the memory resources are mapped to zero.
After disabling this code block, the memory regions are mapped out
fine (but still no IO):
Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c,
and post the results.
When this code is disabled then you're just getting the leftovers from
U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own
scan and its own allocation of memory/IO address space and this code
is needed to make sure that happens.
g.
quoted
static void
mpc52xx_pci_fixup_resources(struct pci_dev *dev)
{
int i;
pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n",
dev->vendor, dev->device);
/* We don't rely on boot loader for PCI and resets all
devices */
for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) {
struct resource *res =3D &dev->resource[i];
if (res->end > res->start) { /* Only valid resources */
res->end -=3D res->start;
res->start =3D 0;
res->flags |=3D IORESOURCE_UNSET;
}
}
What is the purpose of this code? Since all resources are reset here,
where are they inteded to be re-allocated?
Here is the bootlog with the aforementioned code enabled:
reading cuImage.lite5200b
1833699 bytes read
## Booting kernel from Legacy Image at 00201400 ...
Image Name: Linux-2.6.28
Created: 2009-02-05 6:54:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1833635 Bytes =3D 1.7 MB
Load Address: 00400000
Entry Point: 004005a0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
[ 0.000000] Using lite5200 machine description
[ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc
version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET
2009
[ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00
[ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges:
[ 0.000000] MEM 0x0000000050000000..0x000000005fffffff ->
0x0000000050000000
[ 0.000000] IO 0x0000000060000000..0x0000000060ffffff ->
0x0000000000000000
[ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00)
[ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff,
.flags=3D200}
[ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100}
.io_base_phys=3D0x60000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00004000
[ 0.000000] Normal 0x00004000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/de=
v/sda2
quoted
quoted
rw
[ 0.000000] MPC52xx PIC is up and running!
[ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[ 0.000000] clocksource: timebase mult[7d00000] shift[22] registered
[ 0.000263] console [ttyPSC0] enabled
[ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.147433] Memory: 60844k/65536k available (3704k kernel code,
4624k reserved, 156k data, 117k bss, 180k init)
[ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObjec=
ts=3D0,
quoted
quoted
CPUs=3D1, Nodes=3D1
[ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744)
[ 0.236265] Mount-cache hash table entries: 512
[ 0.245719] net_namespace: 288 bytes
[ 0.250237] NET: Registered protocol family 16
[ 0.284887] PCI: Probing PCI hardware
[ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809
[ 0.294799] PCI:0000:00:17.0 Resource 0
0000000050400000-00000000507fffff [21208] fixup...
[ 0.303180] PCI:0000:00:17.0
0000000050400000-00000000507fffff
[ 0.309998] PCI:0000:00:17.0 Resource 1
0000000050800000-0000000050ffffff [20200] fixup...
[ 0.318262] PCI:0000:00:17.0
0000000050800000-0000000050ffffff
[ 0.325062] PCI:0000:00:17.0 Resource 2
0000000060000000-000000006000000f [20101] fixup...
[ 0.333326] PCI:0000:00:17.0
0000000060000000-000000006000000f
[ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.345242] PCI:0000:00:18.0 Resource 0
0000000051000000-00000000513fffff [21208] fixup...
[ 0.353519] PCI:0000:00:18.0
0000000051000000-00000000513fffff
[ 0.360319] PCI:0000:00:18.0 Resource 1
0000000051800000-0000000051ffffff [20200] fixup...
[ 0.368583] PCI:0000:00:18.0
0000000051800000-0000000051ffffff
[ 0.375383] PCI:0000:00:18.0 Resource 2
0000000060000010-000000006000001f [20101] fixup...
[ 0.383647] PCI:0000:00:18.0
0000000060000010-000000006000001f
[ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.395549] PCI:0000:00:19.0 Resource 0
0000000052000000-00000000523fffff [21208] fixup...
[ 0.403826] PCI:0000:00:19.0
0000000052000000-00000000523fffff
[ 0.410626] PCI:0000:00:19.0 Resource 1
0000000052800000-0000000052ffffff [20200] fixup...
[ 0.418889] PCI:0000:00:19.0
0000000052800000-0000000052ffffff
[ 0.425690] PCI:0000:00:19.0 Resource 2
0000000060000020-000000006000002f [20101] fixup...
[ 0.433954] PCI:0000:00:19.0
0000000060000020-000000006000002f
[ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.445854] PCI:0000:00:1a.0 Resource 0
0000000053000000-00000000533fffff [21208] fixup...
[ 0.454130] PCI:0000:00:1a.0
0000000053000000-00000000533fffff
[ 0.460930] PCI:0000:00:1a.0 Resource 1
0000000053800000-0000000053ffffff [20200] fixup...
[ 0.469194] PCI:0000:00:1a.0
0000000053800000-0000000053ffffff
[ 0.475994] PCI:0000:00:1a.0 Resource 2
0000000060000030-000000006000003f [20101] fixup...
[ 0.484258] PCI:0000:00:1a.0
0000000060000030-000000006000003f
[ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.495999] PCI: Fixup bus 0 (PHB)
[ 0.499383] PCI: device 0000:00:16.0 OF node: <none>
[ 0.504371] PCI: device 0000:00:17.0 OF node: <none>
[ 0.509363] PCI: device 0000:00:18.0 OF node: <none>
[ 0.514354] PCI: device 0000:00:19.0 OF node: <none>
[ 0.519345] PCI: device 0000:00:1a.0 OF node: <none>
[ 0.524332] Try to map irq for 0000:00:16.0...
[ 0.528808] Try to map irq for 0000:00:17.0...
[ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.543389] -> mapped to linux irq 65
[ 0.547117] Try to map irq for 0000:00:18.0...
[ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.561629] -> mapped to linux irq 65
[ 0.565353] Try to map irq for 0000:00:19.0...
[ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.579863] -> mapped to linux irq 65
[ 0.583587] Try to map irq for 0000:00:1a.0...
[ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.598103] -> mapped to linux irq 65
[ 0.605144] PCI: PHB (bus 0) bridge rsrc 0:
0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO)
[ 0.615266] PCI: PHB (bus 0) bridge rsrc 1:
0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem)
[ 0.625539] PCI: Assigning unassigned resouces...
[ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff]
[ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff]
[ 0.640909] DMA: MPC52xx BestComm driver
[ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok !
[ 0.678739] SCSI subsystem initialized
[ 0.709498] NET: Registered protocol family 2
[ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.762429] TCP established hash table entries: 2048 (order: 2, 1638=
4
quoted
quoted
bytes)
[ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.776224] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.782604] TCP reno registered
[ 0.795054] NET: Registered protocol family 1
[ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc.
[ 0.855699] msgmni has been set to 118
[ 0.861227] alg: No test for stdrng (krng)
[ 0.865651] io scheduler noop registered
[ 0.869658] io scheduler anticipatory registered (default)
[ 0.875224] io scheduler deadline registered
[ 0.879838] io scheduler cfq registered
[ 1.442231] Generic RTC Driver v1.07
[ 1.447145] Serial: MPC52xx PSC UART driver
[ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 130=
)
quoted
quoted
is a MPC52xx PSC
[ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 131=
)
quoted
quoted
is a MPC52xx PSC
[ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 139=
)
quoted
quoted
is a MPC52xx PSC
[ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 140=
)
quoted
quoted
is a MPC52xx PSC
[ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 132=
)
quoted
quoted
is a MPC52xx PSC
[ 1.521689] brd: module loaded
[ 1.535886] loop: module loaded
[ 1.544328] mpc52xx MII bus: probed
[ 1.550220] net eth0: Using PHY at MDIO address 0
[ 1.556124] Driver 'sd' needs updating - please use bus_type methods
[ 1.563224] ata: MPC52xx IDE/ATA libata driver
[ 1.568729] scsi0 : mpc52xx_ata
[ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135
[ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66
[ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA
[ 1.775156] ata1.00: configured for UDMA/33
[ 1.803154] ata1.00: configured for UDMA/33
[ 1.807423] ata1: EH complete
[ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND
2007 PQ: 0 ANSI: 5
[ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.829333] sd 0:0:0:0: [sda] Write Protect is off
[ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.852841] sd 0:0:0:0: [sda] Write Protect is off
[ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.867450] sda: sda1 sda2
[ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit bank
[ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.902529] fc000000.flash: CFI does not contain boot bank
location. Assuming top.
[ 1.910147] number of CFI chips: 1
[ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to
code brokenness.
[ 1.922009] RedBoot partition parsing not available
[ 1.926998] Creating 4 MTD partitions on "fc000000.flash":
[ 1.932547] 0x00000000-0x00500000 : "u-boot"
[ 1.940601] 0x00500000-0x01000000 : "kernel"
[ 1.948071] 0x01000000-0x02000000 : "rootfs"
[ 1.955601] 0x02000000-0x03000000 : "application"
[ 1.964240] i2c /dev entries driver
[ 1.975775] Advanced Linux Sound Architecture Driver Version
1.0.18rc3.
[ 1.983814] ASoC version 0.13.2
[ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device
[ 2.040451] registering ASoC codec driver:
/soc5200@f0000000/i2c@3d00/codec@1a
[ 2.049539] ALSA device list:
[ 2.052591] No soundcards found.
[ 2.057430] TCP cubic registered
[ 2.060765] NET: Registered protocol family 17
[ 2.066886] RPC: Registered udp transport module.
[ 2.071683] RPC: Registered tcp transport module.
[ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck
is recommended
[ 2.094828] VFS: Mounted root (ext2 filesystem).
[ 2.099690] Freeing unused kernel memory: 180k init
On Wed, Feb 4, 2009 at 18:54, Grant Likely [off-list ref]
wrote:
quoted
On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
clock-frequency =3D <0x1e84800>; //<0>; // From boot loa=
der
quoted
quoted
quoted
quoted
interrupts =3D <2 8 0 2 9 0 2 10 0>;
interrupt-parent =3D <&mpc5200_pic>;
bus-range =3D <0 0>;
ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x100000=
00
quoted
quoted
quoted
quoted
0x01000000 0 0x00000000 0x60000000 0 0x01000000=
;
quoted
quoted
quoted
quoted
};
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all
mapped
to zero.
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hmmm. Your ranges property looks okay to me. The MPC5200 setup code
may be doing the wrong thing. Turn on debug at the top of
arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel
output.
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--
H=E4lsningar/Regards
Tobias Knutsson
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--=20
H=E4lsningar/Regards
Tobias Knutsson
I have now found drivers/pci/quirks.c which seems to be the place for
these types of things. However, since this code is unlikely to ever
make it to mainline, is it possible to register a fixup hook in a
platform setup file (lite5200.c and friends)?
On Fri, Feb 6, 2009 at 12:46, Tobias Knutsson [off-list ref] w=
rote:
Ok, I have had a breakthrough. I was trying to find out where the
resources were supposed to be allocated and that was when i found this
section of code in pbus_assign_resources_sorted() in
drivers/pci/setup-bus.c:
/* Don't touch classless devices or host bridges or ioapic=
s. */
if (class =3D=3D PCI_CLASS_NOT_DEFINED ||
class =3D=3D PCI_CLASS_BRIDGE_HOST)
continue;
After that i took a quick look at the PCI-info reported by u-boot.
Sure enough, all boards were reported having class 0. At first i tried
to write a different class type, but as i suspected, the register
seems to be read-only. Therefore I simply commented out the first part
of the if-statement and now the resources seems to get allocated
properly.
However, I do realize that this is not the proper way of solving this
issue. Any ideas on how to fix it without modifying any kernel code?
On Thu, Feb 5, 2009 at 21:03, Tobias Knutsson [off-list ref]=
wrote:
quoted
Hi,
That is exactly what the bootlog shows. Debug output on in both
mpc52xx_pci.c and in pci-common.c. And the discussed code section enable=
d.
quoted
H=E4lsningar / Regards
Tobias Knutsson
On 5 feb 2009, at 17.44, Grant Likely [off-list ref] wrote:
quoted
On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
When enabling the debug-printouts, it came to me that I forgot to
mention something kind of important. Using the standard mpc52xx_pci.c,
even the memory resources are mapped to zero.
After disabling this code block, the memory regions are mapped out
fine (but still no IO):
Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c,
and post the results.
When this code is disabled then you're just getting the leftovers from
U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own
scan and its own allocation of memory/IO address space and this code
is needed to make sure that happens.
g.
quoted
static void
mpc52xx_pci_fixup_resources(struct pci_dev *dev)
{
int i;
pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n",
dev->vendor, dev->device);
/* We don't rely on boot loader for PCI and resets all
devices */
for (i =3D 0; i < DEVICE_COUNT_RESOURCE; i++) {
struct resource *res =3D &dev->resource[i];
if (res->end > res->start) { /* Only valid resources *=
/
quoted
quoted
quoted
res->end -=3D res->start;
res->start =3D 0;
res->flags |=3D IORESOURCE_UNSET;
}
}
What is the purpose of this code? Since all resources are reset here,
where are they inteded to be re-allocated?
Here is the bootlog with the aforementioned code enabled:
reading cuImage.lite5200b
1833699 bytes read
## Booting kernel from Legacy Image at 00201400 ...
Image Name: Linux-2.6.28
Created: 2009-02-05 6:54:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1833635 Bytes =3D 1.7 MB
Load Address: 00400000
Entry Point: 004005a0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
[ 0.000000] Using lite5200 machine description
[ 0.000000] Linux version 2.6.28 (tknutsson@ztn-ubuntu) (gcc
version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET
2009
[ 0.000000] Adding MPC52xx PCI host bridge /pci@f0000d00
[ 0.000000] PCI host bridge /pci@f0000d00 (primary) ranges:
[ 0.000000] MEM 0x0000000050000000..0x000000005fffffff ->
0x0000000050000000
[ 0.000000] IO 0x0000000060000000..0x0000000060ffffff ->
0x0000000000000000
[ 0.000000] mpc52xx_pci_setup(hose=3Dc03ec000, pci_regs=3Dfdffad00)
[ 0.000000] mem_resource[0] =3D {.start=3D50000000, .end=3D5fffffff=
,
quoted
quoted
quoted
.flags=3D200}
[ 0.000000] .io_resource=3D{.start=3D0,.end=3Dffffff,.flags=3D100}
.io_base_phys=3D0x60000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00004000
[ 0.000000] Normal 0x00004000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=3DttyPSC0,115200 root=3D/d=
ev/sda2
quoted
quoted
quoted
rw
[ 0.000000] MPC52xx PIC is up and running!
[ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[ 0.000000] clocksource: timebase mult[7d00000] shift[22] registere=
d
quoted
quoted
quoted
[ 0.000263] console [ttyPSC0] enabled
[ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.147433] Memory: 60844k/65536k available (3704k kernel code,
4624k reserved, 156k data, 117k bss, 180k init)
[ 0.157672] SLUB: Genslabs=3D12, HWalign=3D32, Order=3D0-3, MinObje=
cts=3D0,
quoted
quoted
quoted
CPUs=3D1, Nodes=3D1
[ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=3D127744)
[ 0.236265] Mount-cache hash table entries: 512
[ 0.245719] net_namespace: 288 bytes
[ 0.250237] NET: Registered protocol family 16
[ 0.284887] PCI: Probing PCI hardware
[ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809
[ 0.294799] PCI:0000:00:17.0 Resource 0
0000000050400000-00000000507fffff [21208] fixup...
[ 0.303180] PCI:0000:00:17.0
0000000050400000-00000000507fffff
[ 0.309998] PCI:0000:00:17.0 Resource 1
0000000050800000-0000000050ffffff [20200] fixup...
[ 0.318262] PCI:0000:00:17.0
0000000050800000-0000000050ffffff
[ 0.325062] PCI:0000:00:17.0 Resource 2
0000000060000000-000000006000000f [20101] fixup...
[ 0.333326] PCI:0000:00:17.0
0000000060000000-000000006000000f
[ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.345242] PCI:0000:00:18.0 Resource 0
0000000051000000-00000000513fffff [21208] fixup...
[ 0.353519] PCI:0000:00:18.0
0000000051000000-00000000513fffff
[ 0.360319] PCI:0000:00:18.0 Resource 1
0000000051800000-0000000051ffffff [20200] fixup...
[ 0.368583] PCI:0000:00:18.0
0000000051800000-0000000051ffffff
[ 0.375383] PCI:0000:00:18.0 Resource 2
0000000060000010-000000006000001f [20101] fixup...
[ 0.383647] PCI:0000:00:18.0
0000000060000010-000000006000001f
[ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.395549] PCI:0000:00:19.0 Resource 0
0000000052000000-00000000523fffff [21208] fixup...
[ 0.403826] PCI:0000:00:19.0
0000000052000000-00000000523fffff
[ 0.410626] PCI:0000:00:19.0 Resource 1
0000000052800000-0000000052ffffff [20200] fixup...
[ 0.418889] PCI:0000:00:19.0
0000000052800000-0000000052ffffff
[ 0.425690] PCI:0000:00:19.0 Resource 2
0000000060000020-000000006000002f [20101] fixup...
[ 0.433954] PCI:0000:00:19.0
0000000060000020-000000006000002f
[ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.445854] PCI:0000:00:1a.0 Resource 0
0000000053000000-00000000533fffff [21208] fixup...
[ 0.454130] PCI:0000:00:1a.0
0000000053000000-00000000533fffff
[ 0.460930] PCI:0000:00:1a.0 Resource 1
0000000053800000-0000000053ffffff [20200] fixup...
[ 0.469194] PCI:0000:00:1a.0
0000000053800000-0000000053ffffff
[ 0.475994] PCI:0000:00:1a.0 Resource 2
0000000060000030-000000006000003f [20101] fixup...
[ 0.484258] PCI:0000:00:1a.0
0000000060000030-000000006000003f
[ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065
[ 0.495999] PCI: Fixup bus 0 (PHB)
[ 0.499383] PCI: device 0000:00:16.0 OF node: <none>
[ 0.504371] PCI: device 0000:00:17.0 OF node: <none>
[ 0.509363] PCI: device 0000:00:18.0 OF node: <none>
[ 0.514354] PCI: device 0000:00:19.0 OF node: <none>
[ 0.519345] PCI: device 0000:00:1a.0 OF node: <none>
[ 0.524332] Try to map irq for 0000:00:16.0...
[ 0.528808] Try to map irq for 0000:00:17.0...
[ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.543389] -> mapped to linux irq 65
[ 0.547117] Try to map irq for 0000:00:18.0...
[ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.561629] -> mapped to linux irq 65
[ 0.565353] Try to map irq for 0000:00:19.0...
[ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.579863] -> mapped to linux irq 65
[ 0.583587] Try to map irq for 0000:00:1a.0...
[ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on
/soc5200@f0000000/interrupt-controller@500
[ 0.598103] -> mapped to linux irq 65
[ 0.605144] PCI: PHB (bus 0) bridge rsrc 0:
0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO)
[ 0.615266] PCI: PHB (bus 0) bridge rsrc 1:
0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem)
[ 0.625539] PCI: Assigning unassigned resouces...
[ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff]
[ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff]
[ 0.640909] DMA: MPC52xx BestComm driver
[ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok !
[ 0.678739] SCSI subsystem initialized
[ 0.709498] NET: Registered protocol family 2
[ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.762429] TCP established hash table entries: 2048 (order: 2, 163=
84
quoted
quoted
quoted
bytes)
[ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes=
)
quoted
quoted
quoted
[ 0.776224] TCP: Hash tables configured (established 2048 bind 2048=
)
quoted
quoted
quoted
[ 0.782604] TCP reno registered
[ 0.795054] NET: Registered protocol family 1
[ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc.
[ 0.855699] msgmni has been set to 118
[ 0.861227] alg: No test for stdrng (krng)
[ 0.865651] io scheduler noop registered
[ 0.869658] io scheduler anticipatory registered (default)
[ 0.875224] io scheduler deadline registered
[ 0.879838] io scheduler cfq registered
[ 1.442231] Generic RTC Driver v1.07
[ 1.447145] Serial: MPC52xx PSC UART driver
[ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq =3D 13=
0)
quoted
quoted
quoted
is a MPC52xx PSC
[ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq =3D 13=
1)
quoted
quoted
quoted
is a MPC52xx PSC
[ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq =3D 13=
9)
quoted
quoted
quoted
is a MPC52xx PSC
[ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq =3D 14=
0)
quoted
quoted
quoted
is a MPC52xx PSC
[ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq =3D 13=
2)
quoted
quoted
quoted
is a MPC52xx PSC
[ 1.521689] brd: module loaded
[ 1.535886] loop: module loaded
[ 1.544328] mpc52xx MII bus: probed
[ 1.550220] net eth0: Using PHY at MDIO address 0
[ 1.556124] Driver 'sd' needs updating - please use bus_type method=
s
quoted
quoted
quoted
[ 1.563224] ata: MPC52xx IDE/ATA libata driver
[ 1.568729] scsi0 : mpc52xx_ata
[ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135
[ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66
[ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA
[ 1.775156] ata1.00: configured for UDMA/33
[ 1.803154] ata1.00: configured for UDMA/33
[ 1.807423] ata1: EH complete
[ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND
2007 PQ: 0 ANSI: 5
[ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.829333] sd 0:0:0:0: [sda] Write Protect is off
[ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
(2.00 GB/1.86 GiB)
[ 1.852841] sd 0:0:0:0: [sda] Write Protect is off
[ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.867450] sda: sda1 sda2
[ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit ban=
k
quoted
quoted
quoted
[ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.902529] fc000000.flash: CFI does not contain boot bank
location. Assuming top.
[ 1.910147] number of CFI chips: 1
[ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to
code brokenness.
[ 1.922009] RedBoot partition parsing not available
[ 1.926998] Creating 4 MTD partitions on "fc000000.flash":
[ 1.932547] 0x00000000-0x00500000 : "u-boot"
[ 1.940601] 0x00500000-0x01000000 : "kernel"
[ 1.948071] 0x01000000-0x02000000 : "rootfs"
[ 1.955601] 0x02000000-0x03000000 : "application"
[ 1.964240] i2c /dev entries driver
[ 1.975775] Advanced Linux Sound Architecture Driver Version
1.0.18rc3.
[ 1.983814] ASoC version 0.13.2
[ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device
[ 2.040451] registering ASoC codec driver:
/soc5200@f0000000/i2c@3d00/codec@1a
[ 2.049539] ALSA device list:
[ 2.052591] No soundcards found.
[ 2.057430] TCP cubic registered
[ 2.060765] NET: Registered protocol family 17
[ 2.066886] RPC: Registered udp transport module.
[ 2.071683] RPC: Registered tcp transport module.
[ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck
is recommended
[ 2.094828] VFS: Mounted root (ext2 filesystem).
[ 2.099690] Freeing unused kernel memory: 180k init
On Wed, Feb 4, 2009 at 18:54, Grant Likely [off-list ref]
wrote:
quoted
On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson
[off-list ref] wrote:
quoted
clock-frequency =3D <0x1e84800>; //<0>; // From boot lo=
ader
quoted
quoted
quoted
quoted
quoted
interrupts =3D <2 8 0 2 9 0 2 10 0>;
interrupt-parent =3D <&mpc5200_pic>;
bus-range =3D <0 0>;
ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x10000=
000
quoted
quoted
quoted
quoted
quoted
0x01000000 0 0x00000000 0x60000000 0 0x0100000=
0>;
quoted
quoted
quoted
quoted
quoted
};
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all
mapped
to zero.
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hmmm. Your ranges property looks okay to me. The MPC5200 setup code
may be doing the wrong thing. Turn on debug at the top of
arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel
output.
g.
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--
H=E4lsningar/Regards
Tobias Knutsson
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
--
H=E4lsningar/Regards
Tobias Knutsson
--=20
H=E4lsningar/Regards
Tobias Knutsson
Tobias,
are you starting with 2.6.28 or are you upgrading ?
My system runs very fine with 2.6.27 ....
Tobias Knutsson wrote:
I am currently trying to get an MPC5200-based board to run Linux
2.6.28. Most of the devices are working, however i have some issues
with the PCI-bus. More precisely, the issue is that all of
the cards' IO-regions are mapped to address 0x0.
In my device tree I have the following:
pci@f0000d00 {
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
reg = <0xf0000d00 0x100>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map = <0xb000 0 0 1 &mpc5200_pic 0 0 3 // MPC5200
0xb000 0 0 2 &mpc5200_pic 0 0 3
0xb000 0 0 3 &mpc5200_pic 0 0 3
0xb000 0 0 4 &mpc5200_pic 0 0 3
What's this ? Is the MPC5200 interrupting itself ?
0xb800 0 0 1 &mpc5200_pic 1 1 3 // c64x0
0xb800 0 0 2 &mpc5200_pic 1 1 3
0xb800 0 0 3 &mpc5200_pic 1 1 3
0xb800 0 0 4 &mpc5200_pic 1 1 3
Have you connected 4 IRQ lines to each c64x device ?
0xc000 0 0 1 &mpc5200_pic 1 1 3 // c64x1
0xc000 0 0 2 &mpc5200_pic 1 1 3
0xc000 0 0 3 &mpc5200_pic 1 1 3
0xc000 0 0 4 &mpc5200_pic 1 1 3
0xc800 0 0 1 &mpc5200_pic 1 1 3 // c64x2
0xc800 0 0 2 &mpc5200_pic 1 1 3
0xc800 0 0 3 &mpc5200_pic 1 1 3
0xc800 0 0 4 &mpc5200_pic 1 1 3
0xd000 0 0 1 &mpc5200_pic 1 1 3 // c64x3
0xd000 0 0 2 &mpc5200_pic 1 1 3
0xd000 0 0 3 &mpc5200_pic 1 1 3
0xd000 0 0 4 &mpc5200_pic 1 1 3
0xd800 0 0 1 &mpc5200_pic 1 1 3 // c64x4
0xd800 0 0 2 &mpc5200_pic 1 1 3
0xd800 0 0 3 &mpc5200_pic 1 1 3
0xd800 0 0 4 &mpc5200_pic 1 1 3>;
I'm using an external FPGA and an e1000 NIC connectedt to IRQ2 and IRQ3 :
interrupt-map = <0x5800 0 0 1 &mpc5200_pic 1 2 3
0x5000 0 0 1
&mpc5200_pic 1 3 3>;
clock-frequency = <0x1e84800>; //<0>; // From boot loader
interrupts = <2 8 0 2 9 0 2 10 0>;
interrupt-parent = <&mpc5200_pic>;
bus-range = <0 0>;
ranges = <0x02000000 0 0x50000000 0x50000000 0 0x10000000
0x01000000 0 0x00000000 0x60000000 0 0x01000000>;
};
I'm using a 3 liner :
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all mapped
to zero.
Are you c64x devices responding properly ? Is IO access enabled in the
PCI command register ?
Are they announcing a reasonable window ? How man KBytes ?
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hopefully something is useful to you.
regards,
Andre
MATRIX VISION GmbH, Talstraße 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschäftsführer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
Hi Andre,
I started the development with 2.6.28. Thanks for all of your
suggestions but I managed to find the solution today. The problem was
that the PCI-cards did not have class specified. Adding a fixup hook
to the cards in quirks.c resolved the issue.
On Fri, Feb 6, 2009 at 14:34, Andre Schwarz
[off-list ref] wrote:
Tobias,
are you starting with 2.6.28 or are you upgrading ?
My system runs very fine with 2.6.27 ....
Tobias Knutsson wrote:
quoted
I am currently trying to get an MPC5200-based board to run Linux
2.6.28. Most of the devices are working, however i have some issues
with the PCI-bus. More precisely, the issue is that all of
the cards' IO-regions are mapped to address 0x0.
In my device tree I have the following:
pci@f0000d00 {
#interrupt-cells =3D <1>;
#size-cells =3D <2>;
#address-cells =3D <3>;
device_type =3D "pci";
compatible =3D "fsl,mpc5200b-pci","fsl,mpc5200-pci";
reg =3D <0xf0000d00 0x100>;
interrupt-map-mask =3D <0xf800 0 0 7>;
interrupt-map =3D <0xb000 0 0 1 &mpc5200_pic 0 0 3 // MPC5=
200
quoted
0xb000 0 0 2 &mpc5200_pic 0 0 3
0xb000 0 0 3 &mpc5200_pic 0 0 3
0xb000 0 0 4 &mpc5200_pic 0 0 3
What's this ? Is the MPC5200 interrupting itself ?
No, the PCI-bridge is connected to IRQ0
quoted
0xb800 0 0 1 &mpc5200_pic 1 1 3 // c64x0
0xb800 0 0 2 &mpc5200_pic 1 1 3
0xb800 0 0 3 &mpc5200_pic 1 1 3
0xb800 0 0 4 &mpc5200_pic 1 1 3
Have you connected 4 IRQ lines to each c64x device ?
No, this is just some copy-paste leftovers that should be trimmed down
after some examination of the schematics.
quoted
0xc000 0 0 1 &mpc5200_pic 1 1 3 // c64x1
0xc000 0 0 2 &mpc5200_pic 1 1 3
0xc000 0 0 3 &mpc5200_pic 1 1 3
0xc000 0 0 4 &mpc5200_pic 1 1 3
0xc800 0 0 1 &mpc5200_pic 1 1 3 // c64x2
0xc800 0 0 2 &mpc5200_pic 1 1 3
0xc800 0 0 3 &mpc5200_pic 1 1 3
0xc800 0 0 4 &mpc5200_pic 1 1 3
0xd000 0 0 1 &mpc5200_pic 1 1 3 // c64x3
0xd000 0 0 2 &mpc5200_pic 1 1 3
0xd000 0 0 3 &mpc5200_pic 1 1 3
0xd000 0 0 4 &mpc5200_pic 1 1 3
0xd800 0 0 1 &mpc5200_pic 1 1 3 // c64x4
0xd800 0 0 2 &mpc5200_pic 1 1 3
0xd800 0 0 3 &mpc5200_pic 1 1 3
0xd800 0 0 4 &mpc5200_pic 1 1 3>;
I'm using an external FPGA and an e1000 NIC connectedt to IRQ2 and IRQ3 :
interrupt-map =3D <0x5800 0 0 1 &mpc5200_pic 1 2 3
0x5000 0 0 1 &mpc5200_pic =
1 3
3>;
quoted
clock-frequency =3D <0x1e84800>; //<0>; // From boot load=
er
quoted
interrupts =3D <2 8 0 2 9 0 2 10 0>;
interrupt-parent =3D <&mpc5200_pic>;
bus-range =3D <0 0>;
ranges =3D <0x02000000 0 0x50000000 0x50000000 0 0x1000000=
0
quoted
0x01000000 0 0x00000000 0x60000000 0 0x01000000>=
;
quoted
};
I'm using a 3 liner :
ranges =3D <0x42000000 0 0x80000000 0x80000000 0 0x20000000
0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
quoted
The cards' memory regions are mapped out fine to different addresses
in the 0x50000000-0x60000000 range. However, the IO regions are all mapp=
ed
quoted
to zero.
Are you c64x devices responding properly ? Is IO access enabled in the PC=
I
command register ?
Are they announcing a reasonable window ? How man KBytes ?
quoted
Do you have any idea on what could be wrong or in which direction I
should be looking?
Hopefully something is useful to you.
regards,
Andre
MATRIX VISION GmbH, Talstra=DFe 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch=E4ftsf=FChrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
Hans-Joachim Reich
--=20
H=E4lsningar/Regards
Tobias Knutsson