StorCenter Help?

Folks,

Anyone out there with an 8241 board such as
the IoMega StorCenter who would be willing to
help me debug my arch/powerpc cuImage problems?

I feel like I am missing something very basic in
my port... like, "Did you map this memory right?"
or "Did you set _this_ magic bit?"

I have posted the 3 patches that provide the basic
port and cuImage support as well.  The U-Boot that
I have is still legacy, so I'd like to get linux
working first via the cuImage, and then work on U-Boot.

The problem is that as soon as U-Boot uncompresses the
cuImage and loads it, I get no further console output.

The failing log follows.

And I don't have a BDI-2000 or JTAG thing I can use here.
Which is sort of why I'm tossing this out for general help.

Thanks,
jdl



CPU:   MPC8241 Revision 1.4 at 199.999 MHz: 16 kB I-Cache 16 kB D-Cache
Board: StorCenter
PICR1 is now 00141b98
PICR2 is now 00040605
AMBOR is now c1
DRAM:  64 MB
FLASH:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   PCI device RTL8169#0: unknown chip version, assuming RTL-8169
PCI device: TxConfig = 0x0
RTL8169#0
Hit any key to stop autoboot:  0 
IOMEGA=> 
IOMEGA=> 
IOMEGA=> 
IOMEGA=> 
IOMEGA=> setenv serverip 192.168.0.10
IOMEGA=> setenv ipaddr 192.168.0.25
IOMEGA=> tftp 100000 cuImage.824x
TFTP from server 192.168.0.10; our IP address is 192.168.0.25
Filename 'cuImage.824x'.
Load address: 0x100000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##
done
Bytes transferred = 1337749 (146995 hex)
IOMEGA=> bootm 100000
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.24-rc6-g550234b0-dirty
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1337685 Bytes =  1.3 MB
   Load Address: 00400000
   Entry Point:  00400544
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
   Loading kernel ......

On 1/11/08, Jon Loeliger [off-list ref] wrote:

Folks,

Anyone out there with an 8241 board such as
the IoMega StorCenter who would be willing to
help me debug my arch/powerpc cuImage problems?

I feel like I am missing something very basic in
my port... like, "Did you map this memory right?"
or "Did you set _this_ magic bit?"

I have posted the 3 patches that provide the basic
port and cuImage support as well.  The U-Boot that
I have is still legacy, so I'd like to get linux
working first via the cuImage, and then work on U-Boot.

The problem is that as soon as U-Boot uncompresses the
cuImage and loads it, I get no further console output.

The failing log follows.

And I don't have a BDI-2000 or JTAG thing I can use here.
Which is sort of why I'm tossing this out for general help.

Since you're getting absolutely no output after uncompression it
probably means that you're failing in the boot wrapper... which means
mmu is off, and the serial port is already set up by u-boot.

You should be able to add direct writes to the uart fifo register from
within the bootwrapper code to see how far you get in the progress.

Cheers,
g.

-- 
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.