Regarding MPC8540 IRQ Issue

4 messages, 2 authors, 2007-06-18 · open the first message on its own page

Regarding MPC8540 IRQ Issue

From: sudheer <hidden>
Date: 2007-06-16 09:56:41 

Hello All

I am working on MPC8540 board placing it in the PCI slot of the x86 system.
After system bootup , i could see the powerpc board detected and pci 
config space configured.
But i could not find any IRQ assigned for it.

SetUp:
Host: x86 System- Linux-2.6.9
HOST PCI Slot is 64-bit, 66MHz
Agent: MPC8540 Board.

Here is dump of "lspci -vx " for this device.

04:03.0 Power PC: Motorola MPC8540 (rev 20) (prog-if 01)
        Flags: bus master, 66Mhz, fast devsel, latency 64
        Memory at dee00000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [60] #00 [0000]
00: 57 10 08 00 46 01 b0 00 20 01 20 0b 00 40 00 00
10: 00 00 e0 de 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00

 From the above dump - IRQ Pin & Line of config space shows zeroes.

I tried writing a small module and probing for IRQ generating a message 
interrupt. Though i could see in the 8540 message status register that 
interrupt is generated, i could not get any IRQ when i do the probe. For 
this trial,  i have configured the PIC message enable register, message 
vector/priority and destination registers, processor current task 
priority register (CPTR).

Can anyone give me some suggestions to try out.

Thanks
Sudheer

Re: Regarding MPC8540 IRQ Issue

From: Bhupender Saharan <hidden>
Date: 2007-06-17 00:16:44 

Hi Sudhir,

From the PCI dump it looks like IRQ PIN register is 0. During enumeration
when BIOS sees that IRQ PIN register is 0, it would not allocate any
interrupt for this card and that's why you are seeing IRQ Line register also
as 0 value.

We need to do some work around for this.

 IN the driver you need to register for all the pci vectors( INTA,B,C and
D). You would be called for any interrupt happening on the bus. you have to
check if the interrupt is for you and then claim it otherwise return that
interrupt is not for you.


Regards
Bhupi


On 6/16/07, sudheer [off-list ref] wrote:
Hello All

I am working on MPC8540 board placing it in the PCI slot of the x86
system.
After system bootup , i could see the powerpc board detected and pci
config space configured.
But i could not find any IRQ assigned for it.

SetUp:
Host: x86 System- Linux-2.6.9
HOST PCI Slot is 64-bit, 66MHz
Agent: MPC8540 Board.

Here is dump of "lspci -vx " for this device.

04:03.0 Power PC: Motorola MPC8540 (rev 20) (prog-if 01)
        Flags: bus master, 66Mhz, fast devsel, latency 64
        Memory at dee00000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [60] #00 [0000]
00: 57 10 08 00 46 01 b0 00 20 01 20 0b 00 40 00 00
10: 00 00 e0 de 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00

From the above dump - IRQ Pin & Line of config space shows zeroes.

I tried writing a small module and probing for IRQ generating a message
interrupt. Though i could see in the 8540 message status register that
interrupt is generated, i could not get any IRQ when i do the probe. For
this trial,  i have configured the PIC message enable register, message
vector/priority and destination registers, processor current task
priority register (CPTR).

Can anyone give me some suggestions to try out.

Thanks
Sudheer

_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded

Re: Regarding MPC8540 IRQ Issue

From: sudheer <hidden>
Date: 2007-06-18 14:37:51 

Hi Bhupi
Thanks for the response.
I tried with all the free irqs as per  /proc/interrupts  in request_irq 
function one in each trial.  But in none of them it jumped to interrupt 
handler.
Please let me know whether this is the one you said to try or anything 
else. ?

Thanks
Sudheer

Bhupender Saharan wrote:
Hi Sudhir,

From the PCI dump it looks like IRQ PIN register is 0. During 
enumeration when BIOS sees that IRQ PIN register is 0, it would not 
allocate any interrupt for this card and that's why you are seeing IRQ 
Line register also as 0 value.

We need to do some work around for this.

 IN the driver you need to register for all the pci vectors( INTA,B,C 
and D). You would be called for any interrupt happening on the bus. 
you have to check if the interrupt is for you and then claim it 
otherwise return that interrupt is not for you.


Regards
Bhupi


On 6/16/07, *sudheer* <urwithsudheer@gmail.com 
<mailto:urwithsudheer@gmail.com>> wrote:

    Hello All

    I am working on MPC8540 board placing it in the PCI slot of the
    x86 system.
    After system bootup , i could see the powerpc board detected and pci
    config space configured.
    But i could not find any IRQ assigned for it.

    SetUp:
    Host: x86 System- Linux-2.6.9
    HOST PCI Slot is 64-bit, 66MHz
    Agent: MPC8540 Board.

    Here is dump of "lspci -vx " for this device.

    04:03.0 Power PC: Motorola MPC8540 (rev 20) (prog-if 01)
            Flags: bus master, 66Mhz, fast devsel, latency 64
            Memory at dee00000 (32-bit, non-prefetchable) [size=1M]
            Capabilities: [60] #00 [0000]
    00: 57 10 08 00 46 01 b0 00 20 01 20 0b 00 40 00 00
    10: 00 00 e0 de 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    30: 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00

    From the above dump - IRQ Pin & Line of config space shows zeroes.

    I tried writing a small module and probing for IRQ generating a
    message
    interrupt. Though i could see in the 8540 message status register that
    interrupt is generated, i could not get any IRQ when i do the
    probe. For
    this trial,  i have configured the PIC message enable register,
    message
    vector/priority and destination registers, processor current task
    priority register (CPTR).

    Can anyone give me some suggestions to try out.

    Thanks
    Sudheer

    _______________________________________________
    Linuxppc-embedded mailing list
    Linuxppc-embedded@ozlabs.org <mailto:Linuxppc-embedded@ozlabs.org>
    https://ozlabs.org/mailman/listinfo/linuxppc-embedded






  

    
Re: Regarding MPC8540 IRQ Issue

    

      From: Bhupender Saharan <hidden>

      Date: 2007-06-18 22:18:59 
    

  

  
Hi Sudhir,

You got a try all the interrupt vecrots corressponding to INTA, INTB, INTC
and INTD, Not the free interrupts.

Bhupi


On 6/18/07, sudheer [off-list ref] wrote:
 Hi Bhupi
Thanks for the response.
I tried with all the free irqs as per  /proc/interrupts  in request_irq
function one in each trial.  But in none of them it jumped to interrupt
handler.
Please let me know whether this is the one you said to try or anything
else. ?

Thanks
Sudheer

Bhupender Saharan wrote:

Hi Sudhir,

quoted
From the PCI dump it looks like IRQ PIN register is 0. During enumeration
when BIOS sees that IRQ PIN register is 0, it would not allocate any
interrupt for this card and that's why you are seeing IRQ Line register also
as 0 value.

We need to do some work around for this.

 IN the driver you need to register for all the pci vectors( INTA,B,C and
D). You would be called for any interrupt happening on the bus. you have to
check if the interrupt is for you and then claim it otherwise return that
interrupt is not for you.


Regards
Bhupi


On 6/16/07, sudheer [off-list ref] wrote:
quoted
Hello All

I am working on MPC8540 board placing it in the PCI slot of the x86
system.
After system bootup , i could see the powerpc board detected and pci
config space configured.
But i could not find any IRQ assigned for it.

SetUp:
Host: x86 System- Linux-2.6.9
HOST PCI Slot is 64-bit, 66MHz
Agent: MPC8540 Board.

Here is dump of "lspci -vx " for this device.

04:03.0 Power PC: Motorola MPC8540 (rev 20) (prog-if 01)
        Flags: bus master, 66Mhz, fast devsel, latency 64
        Memory at dee00000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [60] #00 [0000]
00: 57 10 08 00 46 01 b0 00 20 01 20 0b 00 40 00 00
10: 00 00 e0 de 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 00 00 00 00

quoted
From the above dump - IRQ Pin & Line of config space shows zeroes.
I tried writing a small module and probing for IRQ generating a message
interrupt. Though i could see in the 8540 message status register that
interrupt is generated, i could not get any IRQ when i do the probe. For

this trial,  i have configured the PIC message enable register, message
vector/priority and destination registers, processor current task
priority register (CPTR).

Can anyone give me some suggestions to try out.

Thanks
Sudheer

_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded




    
  

  
    

      

        Keyboard shortcuts
      

      

        
          
hback out one level

          
jnext message in thread

          
kprevious message in thread

          
ldrill in

          
Escclose help / fold thread tree

          
?toggle this help