-----Original Message-----
From: Kumar Gala [mailto:galak@kernel.crashing.org]
Sent: Friday, June 30, 2006 7:55 AM
To: Li Yang-r58472
Cc: linuxppc-dev@ozlabs.org
Subject: Re: [PATCH] Add QE device tree definition
On Jun 29, 2006, at 7:53 AM, Li Yang-r58472 wrote:
quoted
This is the device tree definition for QE SOC for Freescale CPUs.
I have discussed with Vitaly. We agreed on having CPM and QE
definition ultimately merged. He will add in CPM specified
definition later.
Signed-off-by: Jiang Bo <redacted>
Signed-off-by: Li Yang <redacted>
Signed-off-by: Kim Phillips <redacted>
Signed-off-by: Vitaly Bordug <redacted>
---
Documentation/powerpc/booting-without-of.txt | 222 ++++++++++++++++
++++++++++
1 files changed, 222 insertions(+), 0 deletions(-)
diff --git a/Documentation/powerpc/booting-without-of.txt b/
Documentation/powerpc/booting-without-of.txt
index 217e517..096063f 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -1442,6 +1442,227 @@ platforms are moved over to use the flat
};
+ h) Freescale QUICC Engine module (QE)
+ This represents qe module that is installed on PowerQUICC II Pro.
+ Hopefully it will merge backward compatibility with CPM/CPM2.
+ Basically, it is a bus of devices, that could act more or less
+ as a complete entity (UCC, USB etc ). All of them should besiblings on
+ the "root" qe node, using the common properties from there.
+ The description below applies to the the qe of MPC8360 and
+ more nodes and properties would be extended in the future.
+
+ 1) Root QE device
+
+ Required properties:
+ - device_type : should be "qe";
+ - model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
+ - reg : Offset and length of the register set for the device.
+ - bus-frequency : the clock frequency for QUICC Engine.
+
+ Recommended properties
+ - brg-frequency : the internal clock source frequency for baud-
rate
+ generators in Hz.
+
+ Example:
+ qe@e0100000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ device_type = "qe";
+ model = "QE";
+ ranges = <0 e0100000 00100000>;
+ reg = <e0100000 480>;
+ brg-frequency = <0>;
+ bus-frequency = <179A7B00>;
+ }
+
+
+ 2) SPI (Serial Peripheral Interface)
+
+ Required properties:
+ - device_type : should be "spi".
+ - compatible : should be "fsl_spi".
+ - mode : the spi operation mode, it can be "cpu" or "qe".
What does it mean for the spi to be in "qe" mode?
That means:
The SPI can operate in QE mode or in CPU mode. In QE mode SPI is compatible to the MPC826x SPI, and is controlled by QE RISC. In CPU mode, the SPI is controlled wholly by the CPU without any QE RISC intervention.
quoted
+ - reg : offset to the register set and its length.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+ Example:
+ spi@4c0 {
+ device_type = "spi";
+ compatible = "fsl_spi";
+ reg = <4c0 40>;
+ interrupts = <82 0>;
+ interrupt-parent = <700>;
+ mode = "cpu";
+ };
+
How do we tell the difference between the various spi controllers. I
think we have four of them, three of which are probably pretty
similar. We have the 834x spi, and QE, CPM1, CPM2 SPI.
quoted
+
+ 3) USB (Universal Serial Bus Controller)
+
+ Required properties:
+ - device_type : should be "usb".
+ - compatible : could be "qe_udc" or "fhci-hcd".
+ - model : the could be "host" or "slave".
got a 'l' on mode, if we are slave should we provide more info about
what kinda slave we are (ie, what gadget driver should apply).
quoted
+ - reg : there will be two tuples of "address size". The first
tuple is
+ offset and length of the device registers respectively; the
second is
+ offset and length of the device parameter RAM respectively.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+ Example(slave):
+ usb@6c0 {
+ device_type = "usb";
+ compatible = "qe_udc";
+ reg = <6c0 40 8B00 100>;
+ interrupts = <8b 0>;
+ interrupt-parent = <700>;
+ mode = "slave";
+ };
+
+
+ 4) UCC (Unified Communications Controllers)
Why dont you create a sub section for network, and in the future
additional subsections can be added for the different device_types.
quoted
+
+ Required properties:
+ - device_type : should be "network", "hldc", "uart", "transparent"
+ "bisync" or "atm".
+ - compatible : could be "ucc_geth" or "fsl_atm" and so on.
+ - model : should be "UCC".
+ - device-id : the ucc number(1-8), corresponding to UCCx in UM.
+ - reg : there will be two tuples of "address size". The first
tuple is
+ offset and length of the device registers respectively; the
second is
+ offset and length of the device parameter RAM respectively.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - pio-handle : The phandle for the Parallel I/O port
configuration.
+
+ Required properties for network device_type:
+ - mac-address : list of bytes representing the ethernet address.
+ - rx-clock : a string represents the UCC receive clock source.
+ "brgx" : clock source is BRG1~BRG16 respectively;
+ "clkx" : clock source is QE_CLK1~QE_CLK24 respectively.
+ others : clock source is disabled;
+ - tx-clock: a string represents the UCC transmit clock source;
+ "brgx" : clock source is BRG1~BRG16 respectively;
+ "clkx" : clock source is QE_CLK1~QE_CLK24 respectively.
+ others : clock source is disabled;
+ - phy-handle : The phandle for the PHY connected to this
controller.
+
+ Example:
+ ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ model = "UCC";
+ device-id = <1>;
+ reg = <2000 200 8400 100>;
+ interrupts = <a0 0>;
+ interrupt-parent = <700>;
+ mac-address = [ 00 04 9f 00 23 23 ];
+ rx-clock = "none";
+ tx-clock = "clk9";
+ phy-handle = <212000>;
+ pio-handle = <140001>;
+ };
+
+
+ 5) Parallel I/O Ports
+
+ This node configures Parallel I/O ports for CPUs with QE support.
+ The node should reside in the "soc" node of the tree. For each
+ device that using parallel I/O ports, a child node should be
created.
+ See the definition of the Pin configuration nodes below for more
+ information.
+
+ Required properties:
+ - device_type : should be "par_io".
+ - reg : offset to the register set and its length.
+
+ Example:
+ par_io@1400 {
+ reg = <1400 100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "par_io";
+ ucc_pin@01 {
+ ......
+ };
+
Can you explain this further, I'm not getting the relationship
between a par_io & ucc_pin. An example maybe helpful.
Each QE device needs to configure Parallel I/O Ports pin configuration in order to work, for example the configuration for ucc1 is ucc_pin@01. par_io is a container for all these configurations and gives the base for parallel io port register. I will paste dts file for 8360 to give an example.
quoted
+
+ 6) Pin configuration nodes
+
+ Required properties:
+ - linux,phandle : phandle of this node; likely referenced by a QE
+ device.
+ - pio-map : array of pin configurations. Each pin is defined by 6
+ integers. The six numbers are respectively: port, pin, dir,
+ open_drain, assignment, has_irq.
+ - port : port number of the pin; 0-6 represent port A-G in UM.
+ - pin : pin number in the port.
+ - dir : direction of the pin, should encode as follows:
+
+ 0 = The pin is disabled
+ 1 = The pin is an output
+ 2 = The pin is an input
+ 3 = The pin is I/O
+
+ - open_drain : indicates the pin is normal or wired-OR:
+
+ 0 = The pin is actively driven as an output
+ 1 = The pin is an open-drain driver. As an output, the pin is
+ driven active-low, otherwise it is three-stated.
+
+ - assignment : function number of the pin according to the
Pin Assignment
+ tables in User Manual. Each pin can have up to 4 possible
functions in
+ QE and two options for CPM.
+ - has_irq : indicates if the pin is used as source of exteral
+ interrupts.
+
+ Example:
+ ucc_pin@01 {
+ linux,phandle = <140001>;
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0 3 1 0 1 0 /* TxD0 */
+ 0 4 1 0 1 0 /* TxD1 */
+ 0 5 1 0 1 0 /* TxD2 */
+ 0 6 1 0 1 0 /* TxD3 */
+ 1 6 1 0 3 0 /* TxD4 */
+ 1 7 1 0 1 0 /* TxD5 */
+ 1 9 1 0 2 0 /* TxD6 */
+ 1 a 1 0 2 0 /* TxD7 */
+ 0 9 2 0 1 0 /* RxD0 */
+ 0 a 2 0 1 0 /* RxD1 */
+ 0 b 2 0 1 0 /* RxD2 */
+ 0 c 2 0 1 0 /* RxD3 */
+ 0 d 2 0 1 0 /* RxD4 */
+ 1 1 2 0 2 0 /* RxD5 */
+ 1 0 2 0 2 0 /* RxD6 */
+ 1 4 2 0 2 0 /* RxD7 */
+ 0 7 1 0 1 0 /* TX_EN */
+ 0 8 1 0 1 0 /* TX_ER */
+ 0 f 2 0 1 0 /* RX_DV */
+ 0 10 2 0 1 0 /* RX_ER */
+ 0 0 2 0 1 0 /* RX_CLK */
+ 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
+ 2 8 2 0 1 0>; /* GTX125 - CLK9 */
+ };
+
+
More devices will be defined as this spec matures.
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
[snip]
quoted
quoted
+ 2) SPI (Serial Peripheral Interface)
+
+ Required properties:
+ - device_type : should be "spi".
+ - compatible : should be "fsl_spi".
+ - mode : the spi operation mode, it can be "cpu" or "qe".
What does it mean for the spi to be in "qe" mode?
That means:
The SPI can operate in QE mode or in CPU mode. In QE mode SPI is
compatible to the MPC826x SPI, and is controlled by QE RISC. In CPU
mode, the SPI is controlled wholly by the CPU without any QE RISC
intervention.
In QE mode does software get involved at all?
quoted
quoted
+ - reg : offset to the register set and its length.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded
based on
+ the information in section 2) depending on the type of
interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller
that
+ services interrupts for this device.
+
+ Example:
+ spi@4c0 {
+ device_type = "spi";
+ compatible = "fsl_spi";
+ reg = <4c0 40>;
+ interrupts = <82 0>;
+ interrupt-parent = <700>;
+ mode = "cpu";
+ };
+
[snip]
quoted
quoted
+ 5) Parallel I/O Ports
+
+ This node configures Parallel I/O ports for CPUs with QE
support.
+ The node should reside in the "soc" node of the tree. For each
+ device that using parallel I/O ports, a child node should be
created.
+ See the definition of the Pin configuration nodes below for more
+ information.
+
+ Required properties:
+ - device_type : should be "par_io".
+ - reg : offset to the register set and its length.
+
+ Example:
+ par_io@1400 {
+ reg = <1400 100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "par_io";
+ ucc_pin@01 {
+ ......
+ };
+
Can you explain this further, I'm not getting the relationship
between a par_io & ucc_pin. An example maybe helpful.
Each QE device needs to configure Parallel I/O Ports pin
configuration in order to work, for example the configuration for
ucc1 is ucc_pin@01. par_io is a container for all these
configurations and gives the base for parallel io port register. I
will paste dts file for 8360 to give an example.
Maybe its the name that's confusing me, ucc_pin@01 describes what
exactly? A single pin? or all the pin configs for ucc 1?
quoted
quoted
+
+ 6) Pin configuration nodes
+
+ Required properties:
+ - linux,phandle : phandle of this node; likely referenced by
a QE
+ device.
+ - pio-map : array of pin configurations. Each pin is defined
by 6
+ integers. The six numbers are respectively: port, pin, dir,
+ open_drain, assignment, has_irq.
+ - port : port number of the pin; 0-6 represent port A-G in UM.
+ - pin : pin number in the port.
+ - dir : direction of the pin, should encode as follows:
+
+ 0 = The pin is disabled
+ 1 = The pin is an output
+ 2 = The pin is an input
+ 3 = The pin is I/O
+
+ - open_drain : indicates the pin is normal or wired-OR:
+
+ 0 = The pin is actively driven as an output
+ 1 = The pin is an open-drain driver. As an output, the pin is
+ driven active-low, otherwise it is three-stated.
+
+ - assignment : function number of the pin according to the
Pin Assignment
+ tables in User Manual. Each pin can have up to 4 possible
functions in
+ QE and two options for CPM.
+ - has_irq : indicates if the pin is used as source of exteral
+ interrupts.
+
+ Example:
+ ucc_pin@01 {
+ linux,phandle = <140001>;
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0 3 1 0 1 0 /* TxD0 */
+ 0 4 1 0 1 0 /* TxD1 */
+ 0 5 1 0 1 0 /* TxD2 */
+ 0 6 1 0 1 0 /* TxD3 */
+ 1 6 1 0 3 0 /* TxD4 */
+ 1 7 1 0 1 0 /* TxD5 */
+ 1 9 1 0 2 0 /* TxD6 */
+ 1 a 1 0 2 0 /* TxD7 */
+ 0 9 2 0 1 0 /* RxD0 */
+ 0 a 2 0 1 0 /* RxD1 */
+ 0 b 2 0 1 0 /* RxD2 */
+ 0 c 2 0 1 0 /* RxD3 */
+ 0 d 2 0 1 0 /* RxD4 */
+ 1 1 2 0 2 0 /* RxD5 */
+ 1 0 2 0 2 0 /* RxD6 */
+ 1 4 2 0 2 0 /* RxD7 */
+ 0 7 1 0 1 0 /* TX_EN */
+ 0 8 1 0 1 0 /* TX_ER */
+ 0 f 2 0 1 0 /* RX_DV */
+ 0 10 2 0 1 0 /* RX_ER */
+ 0 0 2 0 1 0 /* RX_CLK */
+ 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
+ 2 8 2 0 1 0>; /* GTX125 - CLK9 */
+ };
+
+
More devices will be defined as this spec matures.
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
On Jun 29, 2006, at 22:36, Li Yang-r58472 wrote:
quoted
quoted
+
+
+ 2) SPI (Serial Peripheral Interface)
+
+ Required properties:
+ - device_type : should be "spi".
+ - compatible : should be "fsl_spi".
+ - mode : the spi operation mode, it can be "cpu" or "qe".
What does it mean for the spi to be in "qe" mode?
That means:
The SPI can operate in QE mode or in CPU mode. In QE mode SPI is
compatible to the MPC826x SPI, and is controlled by QE RISC. In CPU
mode, the SPI is controlled wholly by the CPU without any QE RISC
intervention.
Doesn't that mean the "cpu" SPI isn't part of the QE device? I kind
of feel like it shouldn't be part of the QE node, then. Or is it
actually one device that can act in two different modes?
quoted
quoted
+ - reg : offset to the register set and its length.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded
based on
+ the information in section 2) depending on the type of
interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller
that
+ services interrupts for this device.
+
+ Example:
+ spi@4c0 {
+ device_type = "spi";
+ compatible = "fsl_spi";
+ reg = <4c0 40>;
+ interrupts = <82 0>;
+ interrupt-parent = <700>;
+ mode = "cpu";
+ };
+
How do we tell the difference between the various spi controllers. I
think we have four of them, three of which are probably pretty
similar. We have the 834x spi, and QE, CPM1, CPM2 SPI.
quoted
+
+ 3) USB (Universal Serial Bus Controller)
+
+ Required properties:
+ - device_type : should be "usb".
+ - compatible : could be "qe_udc" or "fhci-hcd".
+ - model : the could be "host" or "slave".
got a 'l' on mode, if we are slave should we provide more info about
what kinda slave we are (ie, what gadget driver should apply).
quoted
+ - reg : there will be two tuples of "address size". The first
tuple is
+ offset and length of the device registers respectively; the
second is
+ offset and length of the device parameter RAM respectively.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded
based on
+ the information in section 2) depending on the type of
interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller
that
+ services interrupts for this device.
+
+ Example(slave):
+ usb@6c0 {
+ device_type = "usb";
+ compatible = "qe_udc";
+ reg = <6c0 40 8B00 100>;
+ interrupts = <8b 0>;
+ interrupt-parent = <700>;
+ mode = "slave";
+ };
+
+
+ 4) UCC (Unified Communications Controllers)
Why dont you create a sub section for network, and in the future
additional subsections can be added for the different device_types.
quoted
+
+ Required properties:
+ - device_type : should be "network", "hldc", "uart",
"transparent"
+ "bisync" or "atm".
+ - compatible : could be "ucc_geth" or "fsl_atm" and so on.
+ - model : should be "UCC".
+ - device-id : the ucc number(1-8), corresponding to UCCx in UM.
+ - reg : there will be two tuples of "address size". The first
tuple is
+ offset and length of the device registers respectively; the
second is
+ offset and length of the device parameter RAM respectively.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded
based on
+ the information in section 2) depending on the type of
interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller
that
+ services interrupts for this device.
+ - pio-handle : The phandle for the Parallel I/O port
configuration.
+
+ Required properties for network device_type:
+ - mac-address : list of bytes representing the ethernet address.
+ - rx-clock : a string represents the UCC receive clock source.
+ "brgx" : clock source is BRG1~BRG16 respectively;
+ "clkx" : clock source is QE_CLK1~QE_CLK24 respectively.
+ others : clock source is disabled;
+ - tx-clock: a string represents the UCC transmit clock source;
+ "brgx" : clock source is BRG1~BRG16 respectively;
+ "clkx" : clock source is QE_CLK1~QE_CLK24 respectively.
+ others : clock source is disabled;
+ - phy-handle : The phandle for the PHY connected to this
controller.
+
+ Example:
+ ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ model = "UCC";
+ device-id = <1>;
+ reg = <2000 200 8400 100>;
+ interrupts = <a0 0>;
+ interrupt-parent = <700>;
+ mac-address = [ 00 04 9f 00 23 23 ];
+ rx-clock = "none";
+ tx-clock = "clk9";
+ phy-handle = <212000>;
+ pio-handle = <140001>;
+ };
+
+
+ 5) Parallel I/O Ports
+
+ This node configures Parallel I/O ports for CPUs with QE
support.
+ The node should reside in the "soc" node of the tree. For each
+ device that using parallel I/O ports, a child node should be
created.
+ See the definition of the Pin configuration nodes below for more
+ information.
+
+ Required properties:
+ - device_type : should be "par_io".
+ - reg : offset to the register set and its length.
+
+ Example:
+ par_io@1400 {
+ reg = <1400 100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "par_io";
+ ucc_pin@01 {
+ ......
+ };
+
Can you explain this further, I'm not getting the relationship
between a par_io & ucc_pin. An example maybe helpful.
Each QE device needs to configure Parallel I/O Ports pin
configuration in order to work, for example the configuration for
ucc1 is ucc_pin@01. par_io is a container for all these
configurations and gives the base for parallel io port register. I
will paste dts file for 8360 to give an example.
quoted
quoted
+
+ 6) Pin configuration nodes
+
+ Required properties:
+ - linux,phandle : phandle of this node; likely referenced by
a QE
+ device.
+ - pio-map : array of pin configurations. Each pin is defined
by 6
+ integers. The six numbers are respectively: port, pin, dir,
+ open_drain, assignment, has_irq.
+ - port : port number of the pin; 0-6 represent port A-G in UM.
+ - pin : pin number in the port.
+ - dir : direction of the pin, should encode as follows:
+
+ 0 = The pin is disabled
+ 1 = The pin is an output
+ 2 = The pin is an input
+ 3 = The pin is I/O
+
+ - open_drain : indicates the pin is normal or wired-OR:
+
+ 0 = The pin is actively driven as an output
+ 1 = The pin is an open-drain driver. As an output, the pin is
+ driven active-low, otherwise it is three-stated.
+
+ - assignment : function number of the pin according to the
Pin Assignment
+ tables in User Manual. Each pin can have up to 4 possible
functions in
+ QE and two options for CPM.
+ - has_irq : indicates if the pin is used as source of exteral
+ interrupts.
+
+ Example:
+ ucc_pin@01 {
+ linux,phandle = <140001>;
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0 3 1 0 1 0 /* TxD0 */
+ 0 4 1 0 1 0 /* TxD1 */
+ 0 5 1 0 1 0 /* TxD2 */
+ 0 6 1 0 1 0 /* TxD3 */
+ 1 6 1 0 3 0 /* TxD4 */
+ 1 7 1 0 1 0 /* TxD5 */
+ 1 9 1 0 2 0 /* TxD6 */
+ 1 a 1 0 2 0 /* TxD7 */
+ 0 9 2 0 1 0 /* RxD0 */
+ 0 a 2 0 1 0 /* RxD1 */
+ 0 b 2 0 1 0 /* RxD2 */
+ 0 c 2 0 1 0 /* RxD3 */
+ 0 d 2 0 1 0 /* RxD4 */
+ 1 1 2 0 2 0 /* RxD5 */
+ 1 0 2 0 2 0 /* RxD6 */
+ 1 4 2 0 2 0 /* RxD7 */
+ 0 7 1 0 1 0 /* TX_EN */
+ 0 8 1 0 1 0 /* TX_ER */
+ 0 f 2 0 1 0 /* RX_DV */
+ 0 10 2 0 1 0 /* RX_ER */
+ 0 0 2 0 1 0 /* RX_CLK */
+ 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
+ 2 8 2 0 1 0>; /* GTX125 - CLK9 */
+ };
+
+
More devices will be defined as this spec matures.
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev