Michaêl,
I can't connect the chip as a byte wide device due to performance
degradation.
Due to other constraints, I can't invert MSB and LSB. In fact, due to color
mapping, if I work in 8 bit per pixel, I must address my framebuffer in big
endian mode. In 16 bit per pixel, I need to use little endian mode.
So I really need to change the endian attribute.
Thanks for your answer
Laurent
"Michael Meriin" [off-list ref] on 14/10/2002 10:57:00
To: linuxppc-embedded@lists.linuxppc.org, Laurent
Mohin/SE/Wavetek@Global
cc:
Subject: Re: How to change endian attribute for a memory region
I'm trying to interface a 405GP chip with an EPSON S1D13506 graphic
controller. Because the EPSON chip is a little endian, I need to have my
framebuffer memory acceded in little endian mode.
What is the best way to change endian attribute for a specific memory
region (ioremap little endian)?
Laurent
I suggest you to connect it to the uP as a byte wide device, this will
immediately solve your problem.
The second way you can do it for 16 bit bus to connect MSB and LSB wise a
wiser.
Best Regards,
Michael Meriin
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Stefan,
why don't you use the MD4 signal of the Epson Chip to configure it as big
endian device? Or am I missing something here?
Best regards,
Stefan.
First of all it is not my implementation problem :))
You are right you can use this signal, but in my implementation for 13704
it was impossible to use it, because of other signals constrains:
this signal was possible to be used only for 68000 bus.
So in our case (MPC855) we simply flipped the data bus, by the way only
after that we
found out that this solution was suggested by Epson too.
Best Regards,
Michael Meriin
quoted
Betreff: Re: How to change endian attribute for a memory region
Michaêl,
I can't connect the chip as a byte wide device due to performance
degradation.
Due to other constraints, I can't invert MSB and LSB. In fact,
due to color
mapping, if I work in 8 bit per pixel, I must address my
framebuffer in big
endian mode. In 16 bit per pixel, I need to use little endian mode.
So I really need to change the endian attribute.
Thanks for your answer
Laurent
"Michael Meriin" [off-list ref] on 14/10/2002 10:57:00
To: linuxppc-embedded@lists.linuxppc.org, Laurent
Mohin/SE/Wavetek@Global
cc:
Subject: Re: How to change endian attribute for a memory region
quoted
I'm trying to interface a 405GP chip with an EPSON S1D13506 graphic
controller. Because the EPSON chip is a little endian, I need to have
my
quoted
quoted
framebuffer memory acceded in little endian mode.
What is the best way to change endian attribute for a specific memory
region (ioremap little endian)?
Laurent
I suggest you to connect it to the uP as a byte wide device, this will
immediately solve your problem.
The second way you can do it for 16 bit bus to connect MSB and LSB wise
a
quoted
wiser.
quoted
Best Regards,
Michael Meriin
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Michael,
why don't you use the MD4 signal of the Epson Chip to configure it as big
endian device? Or am I missing something here?
Best regards,
Stefan.
-----Ursprüngliche Nachricht-----
Von: owner-linuxppc-embedded@lists.linuxppc.org
[mailto:owner-linuxppc-embedded@lists.linuxppc.org]Im Auftrag von
Laurent Mohin
Gesendet: Dienstag, 15. Oktober 2002 11:08
An: Michael Meriin
Cc: linuxppc-embedded@lists.linuxppc.org
Betreff: Re: How to change endian attribute for a memory region
Michaêl,
I can't connect the chip as a byte wide device due to performance
degradation.
Due to other constraints, I can't invert MSB and LSB. In fact,
due to color
mapping, if I work in 8 bit per pixel, I must address my
framebuffer in big
endian mode. In 16 bit per pixel, I need to use little endian mode.
So I really need to change the endian attribute.
Thanks for your answer
Laurent
"Michael Meriin" [off-list ref] on 14/10/2002 10:57:00
To: linuxppc-embedded@lists.linuxppc.org, Laurent
Mohin/SE/Wavetek@Global
cc:
Subject: Re: How to change endian attribute for a memory region
quoted
I'm trying to interface a 405GP chip with an EPSON S1D13506 graphic
controller. Because the EPSON chip is a little endian, I need to have my
framebuffer memory acceded in little endian mode.
What is the best way to change endian attribute for a specific memory
region (ioremap little endian)?
Laurent
I suggest you to connect it to the uP as a byte wide device, this will
immediately solve your problem.
The second way you can do it for 16 bit bus to connect MSB and LSB wise a
wiser.
quoted
Best Regards,
Michael Meriin
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/