Booting sandpoint from ide disk

Hi,

does anyone have a good solution for booting sandpoint X3 (cpu 7410, altivec
supported) from ide hard disk? Dink32 does not seem to support anything like
that and ppcboot does not seem to support that CPU.

//lauri

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

Lauri Ojantakanen wrote:

Hi,

does anyone have a good solution for booting sandpoint X3 (cpu 7410, altivec
supported) from ide hard disk? Dink32 does not seem to support anything like
that and ppcboot does not seem to support that CPU.

If you want to stay with DINK, you can put the zImage in flash and set DINK up
to automatically (or not) jump to where you put it.  The zImage will relocate
itself, uncompress the kernel (in the proper location) and then boot.  With the
correct cmdline, you can use an IDE disk partition for your root filesystem.
Unless you hack DINK, you won't be able to boot a kernel actually sitting on
the IDE disk, you have to put it in flash or get it into memory some other way
first.  As others have already said, you can always use PPCBoot.

Mark


** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

Instant need for booting from ide disk seem to have gone away :( Dink32 does
not start anymore at all. When I restart the machine nothing comes through
the serial cable (settings are correct). I have not touched to any board
switches. Red leds on the altimus board are as follows:

RAM: not active
ROM: not active
stat: not active

Others are active.

On sandpoint main power and standby power -leds are active.

Actually when I recycle the power I get just one totally random character to
minicom (does not happen everytime).

Any ideas?

//lauri

On Thursday 05 September 2002 18:47, Mark A. Greer wrote:

Lauri Ojantakanen wrote:

quoted

Hi,

does anyone have a good solution for booting sandpoint X3 (cpu 7410,
altivec supported) from ide hard disk? Dink32 does not seem to support
anything like that and ppcboot does not seem to support that CPU.

If you want to stay with DINK, you can put the zImage in flash and set DINK
up to automatically (or not) jump to where you put it.  The zImage will
relocate itself, uncompress the kernel (in the proper location) and then
boot.  With the correct cmdline, you can use an IDE disk partition for your
root filesystem. Unless you hack DINK, you won't be able to boot a kernel
actually sitting on the IDE disk, you have to put it in flash or get it
into memory some other way first.  As others have already said, you can
always use PPCBoot.

Mark

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

On Fri, Sep 06, 2002 at 11:02:58AM +0300, Lauri Ojantakanen wrote:

Instant need for booting from ide disk seem to have gone away :( Dink32 does
not start anymore at all. When I restart the machine nothing comes through
the serial cable (settings are correct). I have not touched to any board
switches. Red leds on the altimus board are as follows:

Were you trying to put the kernel in flash or something?  If you've got
access to HW debuggers (like the Abatron BDI) look at what's at
0xFF00_0000, it should start off with a bunch of nop's.

--
Tom Rini (TR1265)
http://gate.crashing.org/~trini/

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

Tom Rini wrote:

On Fri, Sep 06, 2002 at 11:02:58AM +0300, Lauri Ojantakanen wrote:

quoted

Instant need for booting from ide disk seem to have gone away :( Dink32 does
not start anymore at all. When I restart the machine nothing comes through
the serial cable (settings are correct). I have not touched to any board
switches. Red leds on the altimus board are as follows:

Were you trying to put the kernel in flash or something?  If you've got
access to HW debuggers (like the Abatron BDI) look at what's at
0xFF00_0000, it should start off with a bunch of nop's.

Ah, I guess I should have said, "Don't overwrite DINK" if that's what you did.
If you overwrote DINK, you'll have to find a ROM burner & a copy of DINK and put
it back on the FLASH.  After that, you can put the zImage either further back in
that FLASH where id doesn't overwrite any other code or better yet put it in the
secondary FLASH.

Mark


** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

Actually the worst thing is that I did not write anything to flash. I was just
considering to write zImage to flash. I just shutdown the linux running on
that board (booted with bootp) to get into dink and it just did not work
anymore.

//Lauri

On Friday 06 September 2002 20:26, Mark A. Greer wrote:

Tom Rini wrote:

quoted

On Fri, Sep 06, 2002 at 11:02:58AM +0300, Lauri Ojantakanen wrote:

quoted

Instant need for booting from ide disk seem to have gone away :( Dink32
does not start anymore at all. When I restart the machine nothing comes
through the serial cable (settings are correct). I have not touched to
any board switches. Red leds on the altimus board are as follows:

Were you trying to put the kernel in flash or something?  If you've got
access to HW debuggers (like the Abatron BDI) look at what's at
0xFF00_0000, it should start off with a bunch of nop's.

Ah, I guess I should have said, "Don't overwrite DINK" if that's what you
did. If you overwrote DINK, you'll have to find a ROM burner & a copy of
DINK and put it back on the FLASH.  After that, you can put the zImage
either further back in that FLASH where id doesn't overwrite any other code
or better yet put it in the secondary FLASH.

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

On Sun, Sep 08, 2002 at 10:27:24PM +0300, Lauri Ojantakanen wrote:

Actually the worst thing is that I did not write anything to flash. I was just
considering to write zImage to flash. I just shutdown the linux running on
that board (booted with bootp) to get into dink and it just did not work
anymore.

Well, I would make sure everything is properly seated stil then.

--
Tom Rini (TR1265)
http://gate.crashing.org/~trini/

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/