Does th sym53c8xx driver really work on PPC ?

Hi,

just got my very own port of Linux to a PPC
going, but are having problems with the SCSI.
It uses a Symbios 53c875 chip and works fine
if I disable the "Special features" by booting
with sym53c8xx=specf:n, but if I keep these on
there are problems downloading the scripts and
the driver loops with an "Illegal instruction in the
SCRIPT "error.

The thing is that the SCRIPT seems to be written
directly to a region that is ioremap():ed from the
address read from the PCI-config for the RAM.
This cannot possibly be right ?
This address is the local PCI bus address and the
address seen from the PPC will have an offset for
the PCI window, in my case 0xc0000000.

So my questions are:

1. Does ths above reasoning sound OK to you ?
2. Is there anyone that have seen this working with the
  stock 2.2.18 (also tried ths 2.2.14) kernel ?

BRGDS


--
Dag Nygren                               email: dag@newtech.fi
Oy NewTech Ab                            phone: +358 9 8024910
Trasktorpet 3                              fax: +358 9 8024916
02360 ESBO                                 GSM: 0400-426312
FINLAND


** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

Hi Nygren,

We been using the 53c895 chip, OK on our 8240 board running HHL (area51) 2.3.16
linux.
If the '875 has on chip script ram then you have to add code to map it somewhere
'safe'.  I chose 0x80000000

(We don't have a eprom for the SCSI chip on our board, your case may be different.)

This amounts to just setting the appropriate base address in the chip's config
registers.
Also, make sure you have the appropriate '875 config signals terminated
appropriately.  i.e. no eprom, internal sram enabled etc.
And of course, make sure the irq line is pulled up if open drain.  On the '895, the
irq line driver type is programmable.
And make sure the sense line on your PIC is config'd correctly.

File system thruput was tested up to ~10Mb/s read and ~10Mb/s write at the same time.
On a fast40, wide, drive.
Not too bad!

Cheers, Ron

-----Original Message-----
From: owner-linuxppc-embedded@lists.linuxppc.org
[mailto:owner-linuxppc-embedded@lists.linuxppc.org]On Behalf Of Dag
Nygren
Sent: Saturday, January 27, 2001 12:11 AM
To: linuxppc-embedded@lists.linuxppc.org
Subject: Does th sym53c8xx driver really work on PPC ?



Hi,

just got my very own port of Linux to a PPC
going, but are having problems with the SCSI.
It uses a Symbios 53c875 chip and works fine
if I disable the "Special features" by booting
with sym53c8xx=specf:n, but if I keep these on
there are problems downloading the scripts and
the driver loops with an "Illegal instruction in the
SCRIPT "error.

The thing is that the SCRIPT seems to be written
directly to a region that is ioremap():ed from the
address read from the PCI-config for the RAM.
This cannot possibly be right ?
This address is the local PCI bus address and the
address seen from the PPC will have an offset for
the PCI window, in my case 0xc0000000.

So my questions are:

1. Does ths above reasoning sound OK to you ?
2. Is there anyone that have seen this working with the
  stock 2.2.18 (also tried ths 2.2.14) kernel ?

BRGDS


--
Dag Nygren                               email: dag@newtech.fi
Oy NewTech Ab                            phone: +358 9 8024910
Trasktorpet 3                              fax: +358 9 8024916
02360 ESBO                                 GSM: 0400-426312
FINLAND

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/