Hi
When I ported linux to a board with MPC860, 16M RAM and 2M Flash,
I met a problem.
After the program gunzip()(misc.c) the vmlinux image to address 0x0,
the contents from 0x0 to IMAGE_SIZE should be as same as that in
linux/vmlinux, right? I found that they are not same. Only from 0x0
to about 0xb500, they are same.
I don't think gunzip() has any problem.
Do you have any suggestions?
Thanks!
LiuTao
** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/
Hi,
I have had a problem such as yours that was caused by corruption in the
compressed s-record image once it was on the target. I had thought that
Gunzip would catch this, but it did not. How is your image being
transmitted to the target? Is it over a serial link? In my case, the
S-record loader was not checking checksums and occasionally, a serial
transmission error went undetected. Gunzip did not complain, but the
uncompressed image would end up being skewed by a few bytes.
Hope this helps.
LiuTao wrote:
Hi
When I ported linux to a board with MPC860, 16M RAM and 2M Flash,
I met a problem.
After the program gunzip()(misc.c) the vmlinux image to address 0x0,
the contents from 0x0 to IMAGE_SIZE should be as same as that in
linux/vmlinux, right? I found that they are not same. Only from 0x0
to about 0xb500, they are same.
I don't think gunzip() has any problem.
Do you have any suggestions?
Thanks!
LiuTao
--
Jim Lewis
Sr. Field Applications Engineer
MontaVista Software, Inc.
(817)261-9088 http://www.mvista.com
** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/
Hi:
I made zImage first of course. Then I wrote a little program to
extract the image section which is vmlinux.gz from zImage.
I use visionPROBE which is emulator of EST to debug the linux.
I downloaded the program to my board with emulator, then downloaded
the vmlinux.gz to the position of ZIMAGE_OFFSET. I ran the program,
I can see the following message:
loaded at: 00800000 0080B1C8
board data at: 00800158 00800180
relocated to: 007F0100 007F0128
zimage at: 00830263 0088A2AF
avail ram: 0088B000 01000000
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
So I think the vmlinux.gz that I downloaded to the board is correct.
I also compared vmlinux.gz with contents in RAM ZIMAGE_OFFSET, they
are same. But after gunzip, the contents in RAM 0x0 are different
with vmlinux.
Any other suggestions?
Thanks!
LiuTao
Jim Lewis wrote:
Hi,
I have had a problem such as yours that was caused by corruption in the
compressed s-record image once it was on the target. I had thought that
Gunzip would catch this, but it did not. How is your image being
transmitted to the target? Is it over a serial link? In my case, the
S-record loader was not checking checksums and occasionally, a serial
transmission error went undetected. Gunzip did not complain, but the
uncompressed image would end up being skewed by a few bytes.
Hope this helps.
LiuTao wrote:
quoted
Hi
When I ported linux to a board with MPC860, 16M RAM and 2M Flash,
I met a problem.
After the program gunzip()(misc.c) the vmlinux image to address 0x0,
the contents from 0x0 to IMAGE_SIZE should be as same as that in
linux/vmlinux, right? I found that they are not same. Only from 0x0
to about 0xb500, they are same.
I don't think gunzip() has any problem.
Do you have any suggestions?
Thanks!
LiuTao
--
Jim Lewis
Sr. Field Applications Engineer
MontaVista Software, Inc.
(817)261-9088 http://www.mvista.com
** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/