On Tue, Jan 24, 2012 at 11:36:51PM +0100, Linus Walleij wrote:

On Fri, Jan 20, 2012 at 7:22 PM, Stephen Warren [off-list ref] wrote:

quoted

* Rename old pinmux and new pinctrl platform driver and DT match table
 entries, so the new driver gets instantiated.
* Re-write board-pinmux.c, so that it uses pinctrl APIs to configura the
 pinmux.
* Re-write board-*-pinmux.c so that the pinmux configuration tables are
 in pinctrl format.

Ventana's pin mux table needed some edits on top of the basic format
conversion, since some mux options that were previously marked as
reserved are now valid in the new pinctrl driver. Attempting to use the
old reserved names will result in a failure. Specifically, groups lpw0,
lpw2, lsc1, lsck, and lsda were changed from function rsvd4 to displaya,
and group pta was changed from function rsvd2 to hdmi.

All boards' pin mux tables needed some edits on top of the based format
conversion, since function i2c was split into i2c1 (first general I2C
controller) and i2cp (power I2C controller) to better align function
definitions with HW blocks.

Due to the split of mux tables into pure mux and pull/tristate tables,
many entries in the separate Seaboard/Ventana tables could be merged
into the common table, since the entries differed only in the portion
in one of the tables, not both.

Most pin groups allow configuration of mux, tri-state, and pull. However,
some don't allow pull configuration, which is instead configured by new
groups that only allow pull configuration. This is a reflection of the
true HW capabilities, which weren't fully represented by the old pinmux
driver. This required adding new pull table entries for those new groups,
and setting many other entries' pull configuration to
TEGRA_PINCONFIG_DONT_SET.

Signed-off-by: Stephen Warren <redacted>
---
 arch/arm/mach-tegra/board-harmony-pinmux.c   |  362 ++++++++++++++-------
 arch/arm/mach-tegra/board-paz00-pinmux.c     |  362 ++++++++++++++-------
 arch/arm/mach-tegra/board-pinmux.c           |   62 ++++-
 arch/arm/mach-tegra/board-pinmux.h           |   39 ++-
 arch/arm/mach-tegra/board-seaboard-pinmux.c  |  442 ++++++++++++++++---------
 arch/arm/mach-tegra/board-trimslice-pinmux.c |  366 ++++++++++++++--------
 arch/arm/mach-tegra/pinmux.c                 |    6 +-
 drivers/pinctrl/pinctrl-tegra.c              |    6 +-
 8 files changed, 1095 insertions(+), 550 deletions(-)

Can I have Colin's or Olof's ACK on this Tegra stuff too?
Would feel better...

Acked-by: Linus Walleij <redacted>

This series is:

Acked-by: Olof Johansson <redacted>

This should go in through the pinctrl tree, but we have at least one patch
already that depends on it (for cardhu pinmux tables). Since cardhu is still
a quite active board, I expect we might see more patches this merge window,
etc. So I'd like to take that patch (that is not part of this series) through
linux-tegra to reduce conflicts.

To facilitate that, can you land this series in a stable branch in
your tree that you promise not to rebase between now and upstream
submission? That would take care of the dependencies quite nicely,
since we can pull that in as a prereq on the cardhu patch that way.

But all h*ll breaks loose if you rebase that branch... So we need a
strong agreement on that.


-Olof