From: Marek Vasut <marex@denx.de> Date: 2021-07-18 21:14:31
If the backlight enable GPIO is configured as input, the driver currently
unconditionally forces the GPIO to output-enable. This can cause backlight
flicker on boot e.g. in case the GPIO should not be enabled before the PWM
is configured and is correctly pulled low by external resistor.
Fix this by extending the current check to differentiate between backlight
GPIO enable set as input and set as direction unknown. In case of input,
read the GPIO value to determine the pull resistor placement, set the GPIO
as output, and drive that exact value it was pulled to. In case of unknown
direction, retain previous behavior, that is set the GPIO as output-enable.
Fixes: 3698d7e7d221 ("backlight: pwm_bl: Avoid backlight flicker when probed from DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Daniel Thompson <redacted>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Thierry Reding <redacted>
Cc: linux-pwm@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
To: dri-devel@lists.freedesktop.org
---
NOTE: I think this whole auto-detection scheme should just be replaced by a
DT prop, because it is very fragile.
---
drivers/video/backlight/pwm_bl.c | 35 +++++++++++++++++++++++---------
1 file changed, 25 insertions(+), 10 deletions(-)
From: Daniel Thompson <hidden> Date: 2021-07-19 11:22:08
On Sun, Jul 18, 2021 at 11:14:15PM +0200, Marek Vasut wrote:
If the backlight enable GPIO is configured as input, the driver currently
unconditionally forces the GPIO to output-enable. This can cause backlight
flicker on boot e.g. in case the GPIO should not be enabled before the PWM
is configured and is correctly pulled low by external resistor.
Fix this by extending the current check to differentiate between backlight
GPIO enable set as input and set as direction unknown. In case of input,
read the GPIO value to determine the pull resistor placement, set the GPIO
as output, and drive that exact value it was pulled to. In case of unknown
direction, retain previous behavior, that is set the GPIO as output-enable.
Fixes: 3698d7e7d221 ("backlight: pwm_bl: Avoid backlight flicker when probed from DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Daniel Thompson <redacted>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Thierry Reding <redacted>
Cc: linux-pwm@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
To: dri-devel@lists.freedesktop.org
---
NOTE: I think this whole auto-detection scheme should just be replaced by a
DT prop, because it is very fragile.
I have some sympathy for this view... although I think the boat has
already set sail.
However, on the basis of making things less fragile, I think the
underlying problem here is the assumption that it is safe to modify
enable_gpio before the driver has imposed state upon the PWM (this
assumption has always been made and, in addition to systems where the BL
has a phandle will also risks flicker problems on systems where
power_pwm_on_delay is not zero).
This patch does not change the assumption that we can configure the
GPIO before we modify the PWM state. This means it won't fix the problem
for cases there the pin is HiZ by default but whose GPIOD_ASIS state is
neither input nor output.
I wonder if it might be better to move the code to configure the
direction of enable_gpio out of the probe function and into
pwm_backlight_power_on():
if (pb->enable_gpio) {
if (gpiod_get_direction(pb->enable_gpio) != 0))
gpiod_direction_output(pb->enable_gpio, 1);
else
gpiod_set_value_can_sleep(pb->enable_gpio, 1);
}
By the time we reach this function the driver explicitly applies state
to the GPIO then we know what the value must be.
Daniel.
From: Marek Vasut <marex@denx.de> Date: 2021-07-20 20:28:38
On 7/19/21 1:22 PM, Daniel Thompson wrote:
On Sun, Jul 18, 2021 at 11:14:15PM +0200, Marek Vasut wrote:
quoted
If the backlight enable GPIO is configured as input, the driver currently
unconditionally forces the GPIO to output-enable. This can cause backlight
flicker on boot e.g. in case the GPIO should not be enabled before the PWM
is configured and is correctly pulled low by external resistor.
Fix this by extending the current check to differentiate between backlight
GPIO enable set as input and set as direction unknown. In case of input,
read the GPIO value to determine the pull resistor placement, set the GPIO
as output, and drive that exact value it was pulled to. In case of unknown
direction, retain previous behavior, that is set the GPIO as output-enable.
Fixes: 3698d7e7d221 ("backlight: pwm_bl: Avoid backlight flicker when probed from DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Daniel Thompson <redacted>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Thierry Reding <redacted>
Cc: linux-pwm@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
To: dri-devel@lists.freedesktop.org
---
NOTE: I think this whole auto-detection scheme should just be replaced by a
DT prop, because it is very fragile.
I have some sympathy for this view... although I think the boat has
already set sail.
I'm not sure that's correct, we can simply say that any new uses of the
pwm-backlight should specify the initial GPIO configuration, and for the
legacy ones, use whatever is in the code now.
However, on the basis of making things less fragile, I think the
underlying problem here is the assumption that it is safe to modify
enable_gpio before the driver has imposed state upon the PWM (this
assumption has always been made and, in addition to systems where the BL
has a phandle will also risks flicker problems on systems where
power_pwm_on_delay is not zero).
It is safe to modify the GPIO into defined state, but that defined state
is not always out/enabled, that defined state depends on the hardware.
This patch does not change the assumption that we can configure the
GPIO before we modify the PWM state. This means it won't fix the problem
for cases there the pin is HiZ by default but whose GPIOD_ASIS state is
neither input nor output.
That is correct, for pin that is floating, we lost. But then I would
argue that if your backlight-enable GPIO is floating, the hardware is
buggy, I would expect some pull resistor to keep the backlight off on
power on on that GPIO.
I wonder if it might be better to move the code to configure the
direction of enable_gpio out of the probe function and into
pwm_backlight_power_on():
No, I tried that already.
The first thing that is called on boot is pwm_backlight_power_off() to
set the backlight to 0 (and thus set pwm to 0), but since pb->enabled is
false, that is where the function exits with configuring PWM and without
configuring the GPIO state.
I also experimented with some "first time only" flag in those functions,
but that looked ugly and complicated the runtime code.
if (pb->enable_gpio) {
if (gpiod_get_direction(pb->enable_gpio) != 0))
gpiod_direction_output(pb->enable_gpio, 1);
else
gpiod_set_value_can_sleep(pb->enable_gpio, 1);
}
By the time we reach this function the driver explicitly applies state
to the GPIO then we know what the value must be.
From: Daniel Thompson <hidden> Date: 2021-07-21 10:49:22
On Tue, Jul 20, 2021 at 10:28:32PM +0200, Marek Vasut wrote:
On 7/19/21 1:22 PM, Daniel Thompson wrote:
quoted
On Sun, Jul 18, 2021 at 11:14:15PM +0200, Marek Vasut wrote:
quoted
If the backlight enable GPIO is configured as input, the driver currently
unconditionally forces the GPIO to output-enable. This can cause backlight
flicker on boot e.g. in case the GPIO should not be enabled before the PWM
is configured and is correctly pulled low by external resistor.
Fix this by extending the current check to differentiate between backlight
GPIO enable set as input and set as direction unknown. In case of input,
read the GPIO value to determine the pull resistor placement, set the GPIO
as output, and drive that exact value it was pulled to. In case of unknown
direction, retain previous behavior, that is set the GPIO as output-enable.
Fixes: 3698d7e7d221 ("backlight: pwm_bl: Avoid backlight flicker when probed from DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Daniel Thompson <redacted>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Thierry Reding <redacted>
Cc: linux-pwm@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
To: dri-devel@lists.freedesktop.org
---
NOTE: I think this whole auto-detection scheme should just be replaced by a
DT prop, because it is very fragile.
I have some sympathy for this view... although I think the boat has
already set sail.
I'm not sure that's correct, we can simply say that any new uses of the
pwm-backlight should specify the initial GPIO configuration, and for the
legacy ones, use whatever is in the code now.
I'm not 100% against the idea... however if we still have to get the
code to read state from the hardware right for legacy cases that means
we have to do the same work but with fewer people testing it.
quoted
However, on the basis of making things less fragile, I think the
underlying problem here is the assumption that it is safe to modify
enable_gpio before the driver has imposed state upon the PWM (this
assumption has always been made and, in addition to systems where the BL
has a phandle will also risks flicker problems on systems where
power_pwm_on_delay is not zero).
It is safe to modify the GPIO into defined state, but that defined state is
not always out/enabled, that defined state depends on the hardware.
It is only safe to do this once we know what the initial value should be
and I'm not sure that value can comes exclusively from reading the pin.
quoted
This patch does not change the assumption that we can configure the
GPIO before we modify the PWM state. This means it won't fix the problem
for cases there the pin is HiZ by default but whose GPIOD_ASIS state is
neither input nor output.
That is correct, for pin that is floating, we lost. But then I would argue
that if your backlight-enable GPIO is floating, the hardware is buggy, I
would expect some pull resistor to keep the backlight off on power on on
that GPIO.
I didn't say that the pin was floating. I said that the pin was in a HiZ
state meaning it could still be subject to pull up/down.
However there are cases, such as when the regulator is off, where I
think it is entirely legitimate for the enable pin to be floating. The
current driver does the wrong thing here if the pin is set as input
since if the regulator is off the initial enable_gpio value should be 0.
quoted
I wonder if it might be better to move the code to configure the
direction of enable_gpio out of the probe function and into
pwm_backlight_power_on():
No, I tried that already.
The first thing that is called on boot is pwm_backlight_power_off() to set
the backlight to 0 (and thus set pwm to 0), but since pb->enabled is false,
that is where the function exits with configuring PWM and without
configuring the GPIO state.
I also experimented with some "first time only" flag in those functions, but
that looked ugly and complicated the runtime code.
I followed that idea and came to a similar conclusion w.r.t. to the
first time flag.
I think a reasonably elegant approach can be reached by making
pwm_backlight_initial_power_state() responsible for ensuring enable_gpio
matches the observed hardware state (taking into account both the pin
state and the regulator). I think this will fix both your flicker
concerns whilst permitting the legitimate cases for a floating pin.
Something like:
@@ -409,6 +409,33 @@ static bool pwm_backlight_is_linear(struct platform_pwm_backlight_data *data)staticintpwm_backlight_initial_power_state(conststructpwm_bl_data*pb){structdevice_node*node=pb->dev->of_node;+boolactive=true;++/*+*IftheenableGPIOispresent,observable(eitherasinput+*oroutput)andoffthenthebacklightisnotcurrentlyactive.+**/+if(pb->enable_gpio&&gpiod_get_value_cansleep(pb->enable_gpio)==0)+active=false;++if(!regulator_is_enabled(pb->power_supply))+active=false;++if(!pwm_is_enabled(pb->pwm))+active=false;++/*+*Synchronizetheenable_gpiowiththeobservedstateofthe+*hardware.+*/+if(pb->enable_gpio)+gpiod_direction_output(pb->enable_gpio,active);++/*+*Donotchangepb->enabledhere!pb->enabledessentially+*tellsusifweownoneoftheregulator'susecountsand+*rightnowwedonot.+*//* Not booted with device tree or no phandle link to the node */if(!node||!node->phandle)
@@ -420,20 +447,7 @@ static int pwm_backlight_initial_power_state(const struct pwm_bl_data *pb)*assumethatanotherdriverwillenablethebacklightatthe*appropriatetime.Therefore,ifitisdisabled,keepitso.*/--/* if the enable GPIO is disabled, do not enable the backlight */-if(pb->enable_gpio&&gpiod_get_value_cansleep(pb->enable_gpio)==0)-returnFB_BLANK_POWERDOWN;--/* The regulator is disabled, do not enable the backlight */-if(!regulator_is_enabled(pb->power_supply))-returnFB_BLANK_POWERDOWN;--/* The PWM is disabled, keep it like this */-if(!pwm_is_enabled(pb->pwm))-returnFB_BLANK_POWERDOWN;--returnFB_BLANK_UNBLANK;+returnactive?FB_BLANK_UNBLANK:FB_BLANK_POWERDOWN;}staticintpwm_backlight_probe(structplatform_device*pdev)
@@ -486,18 +500,6 @@ static int pwm_backlight_probe(struct platform_device *pdev)gotoerr_alloc;}-/*-*IftheGPIOisnotknowntobealreadyconfiguredasoutput,that-*is,ifgpiod_get_directionreturnseither1or-EINVAL,changethe-*directiontooutputandsettheGPIOasactive.-*DonotforcetheGPIOtoactivewhenitwasalreadyoutputasit-*couldcausebacklightflickeringorwewouldenablethebacklighttoo-*early.Leavethedecisionoftheinitialbacklightstateforlater.-*/-if(pb->enable_gpio&&-gpiod_get_direction(pb->enable_gpio)!=0)-gpiod_direction_output(pb->enable_gpio,1);-pb->power_supply=devm_regulator_get(&pdev->dev,"power");if(IS_ERR(pb->power_supply)){ret=PTR_ERR(pb->power_supply);
From: Marek Vasut <marex@denx.de> Date: 2021-07-21 15:10:02
On 7/21/21 12:49 PM, Daniel Thompson wrote:
[...]
quoted
quoted
quoted
NOTE: I think this whole auto-detection scheme should just be replaced by a
DT prop, because it is very fragile.
I have some sympathy for this view... although I think the boat has
already set sail.
I'm not sure that's correct, we can simply say that any new uses of the
pwm-backlight should specify the initial GPIO configuration, and for the
legacy ones, use whatever is in the code now.
I'm not 100% against the idea... however if we still have to get the
code to read state from the hardware right for legacy cases that means
we have to do the same work but with fewer people testing it.
We can do something like this:
if (of_property_read_bool(np, "enable-active-high"))
gpiod_direction_output(pb->enable_gpio, 1);
else if (of_property_read_bool(np, "enable-active-low"))
gpiod_direction_output(pb->enable_gpio, 0);
else {
WARN_ON_ONCE("Fix your DT"); // or some such notification
... legacy code path ...
}
Note that I picked the same DT prop names as drivers/gpio/gpiolib-of.c
of_gpio_flags_quirks() uses, because we are headed into similar mess
here I'm afraid.
quoted
quoted
However, on the basis of making things less fragile, I think the
underlying problem here is the assumption that it is safe to modify
enable_gpio before the driver has imposed state upon the PWM (this
assumption has always been made and, in addition to systems where the BL
has a phandle will also risks flicker problems on systems where
power_pwm_on_delay is not zero).
It is safe to modify the GPIO into defined state, but that defined state is
not always out/enabled, that defined state depends on the hardware.
It is only safe to do this once we know what the initial value should be
and I'm not sure that value can comes exclusively from reading the pin.
I agree, it is far from perfect, but so is the current code.
However, see below regarding the floating backlight enable pin.
quoted
quoted
This patch does not change the assumption that we can configure the
GPIO before we modify the PWM state. This means it won't fix the problem
for cases there the pin is HiZ by default but whose GPIOD_ASIS state is
neither input nor output.
That is correct, for pin that is floating, we lost. But then I would argue
that if your backlight-enable GPIO is floating, the hardware is buggy, I
would expect some pull resistor to keep the backlight off on power on on
that GPIO.
I didn't say that the pin was floating. I said that the pin was in a HiZ
state meaning it could still be subject to pull up/down.
However there are cases, such as when the regulator is off, where I
think it is entirely legitimate for the enable pin to be floating. The
current driver does the wrong thing here if the pin is set as input
since if the regulator is off the initial enable_gpio value should be 0.
Oh, right, that's a valid point.
So if the pin is input, we can basically toss a coin.
quoted
quoted
I wonder if it might be better to move the code to configure the
direction of enable_gpio out of the probe function and into
pwm_backlight_power_on():
No, I tried that already.
The first thing that is called on boot is pwm_backlight_power_off() to set
the backlight to 0 (and thus set pwm to 0), but since pb->enabled is false,
that is where the function exits with configuring PWM and without
configuring the GPIO state.
I also experimented with some "first time only" flag in those functions, but
that looked ugly and complicated the runtime code.
I followed that idea and came to a similar conclusion w.r.t. to the
first time flag.
I think a reasonably elegant approach can be reached by making
pwm_backlight_initial_power_state() responsible for ensuring enable_gpio
matches the observed hardware state (taking into account both the pin
state and the regulator). I think this will fix both your flicker
concerns whilst permitting the legitimate cases for a floating pin.
Something like:
I think we are getting closer, but there is extra problem to this.
This will fail on iMX GPIO controller, where if the GPIO is output, you
can read its state, but by default that state is what you wrote into the
GPIO output value register, not what is the actual value on the pin
(i.e. consider you have a strong pull resistor that overpowers the driver).
To have a GPIO which is output and sample the actual pin value, you have
to tweak the pinmux and enable the SION bit, then you get the actual
value. But that is specific to the iMX GPIO controller/pinmux.
So I suspect you might still want to check the direction here.
quoted hunk
+ if (!regulator_is_enabled(pb->power_supply))
+ active = false;
+
+ if (!pwm_is_enabled(pb->pwm))
+ active = false;
+
+ /*
+ * Synchronize the enable_gpio with the observed state of the
+ * hardware.
+ */
+ if (pb->enable_gpio)
+ gpiod_direction_output(pb->enable_gpio, active);
+
+ /*
+ * Do not change pb->enabled here! pb->enabled essentially
+ * tells us if we own one of the regulator's use counts and
+ * right now we do not.
+ */
/* Not booted with device tree or no phandle link to the node */
if (!node || !node->phandle)
@@ -420,20 +447,7 @@ static int pwm_backlight_initial_power_state(const struct pwm_bl_data *pb) * assume that another driver will enable the backlight at the * appropriate time. Therefore, if it is disabled, keep it so. */-- /* if the enable GPIO is disabled, do not enable the backlight */- if (pb->enable_gpio && gpiod_get_value_cansleep(pb->enable_gpio) == 0)- return FB_BLANK_POWERDOWN;-- /* The regulator is disabled, do not enable the backlight */- if (!regulator_is_enabled(pb->power_supply))- return FB_BLANK_POWERDOWN;-- /* The PWM is disabled, keep it like this */- if (!pwm_is_enabled(pb->pwm))- return FB_BLANK_POWERDOWN;-- return FB_BLANK_UNBLANK;+ return active ? FB_BLANK_UNBLANK: FB_BLANK_POWERDOWN; } static int pwm_backlight_probe(struct platform_device *pdev)
@@ -486,18 +500,6 @@ static int pwm_backlight_probe(struct platform_device *pdev) goto err_alloc; }- /*- * If the GPIO is not known to be already configured as output, that- * is, if gpiod_get_direction returns either 1 or -EINVAL, change the- * direction to output and set the GPIO as active.- * Do not force the GPIO to active when it was already output as it- * could cause backlight flickering or we would enable the backlight too- * early. Leave the decision of the initial backlight state for later.- */- if (pb->enable_gpio &&- gpiod_get_direction(pb->enable_gpio) != 0)- gpiod_direction_output(pb->enable_gpio, 1);
pwm_backlight_initial_power_state() is still called after
pwm_apply_state() in pwm_backlight_probe(), so that might still be too
late, no ?
From: Daniel Thompson <hidden> Date: 2021-07-21 16:12:56
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
On 7/21/21 12:49 PM, Daniel Thompson wrote:
quoted
quoted
I'm not sure that's correct, we can simply say that any new uses of the
pwm-backlight should specify the initial GPIO configuration, and for the
legacy ones, use whatever is in the code now.
I'm not 100% against the idea... however if we still have to get the
code to read state from the hardware right for legacy cases that means
we have to do the same work but with fewer people testing it.
We can do something like this:
if (of_property_read_bool(np, "enable-active-high"))
gpiod_direction_output(pb->enable_gpio, 1);
else if (of_property_read_bool(np, "enable-active-low"))
gpiod_direction_output(pb->enable_gpio, 0);
else {
WARN_ON_ONCE("Fix your DT"); // or some such notification
... legacy code path ...
}
Note that I picked the same DT prop names as drivers/gpio/gpiolib-of.c
of_gpio_flags_quirks() uses, because we are headed into similar mess here
I'm afraid.
I don't quite understand what you mean here. We are using gpiolib so
for us there is no concept of active-high or active-low. The only
concept for us is whether enable_gpio is asserted or not.
What the DT property would be describing is purely whether the
bootloader left the backlight on or off. This sails very close to the
edge of what is in-scope for DT (at least it does it we can read
the inherited state directly from the hardware).
What it also means decisions about the DT bindings are more about
whether, if the backlight is lit up, the bootloader should also disclose
what it thinks it has established as the PWM duty cycle as well.
Overall I have fairly grave concerns that this simply moves
fragility into the bootloader rather then reducing it.
Daniel.
From: Daniel Thompson <hidden> Date: 2021-07-21 16:43:25
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
On 7/21/21 12:49 PM, Daniel Thompson wrote:
quoted
quoted
quoted
However, on the basis of making things less fragile, I think the
underlying problem here is the assumption that it is safe to modify
enable_gpio before the driver has imposed state upon the PWM (this
assumption has always been made and, in addition to systems where the BL
has a phandle will also risks flicker problems on systems where
power_pwm_on_delay is not zero).
It is safe to modify the GPIO into defined state, but that defined state is
not always out/enabled, that defined state depends on the hardware.
It is only safe to do this once we know what the initial value should be
and I'm not sure that value can comes exclusively from reading the pin.
I agree, it is far from perfect, but so is the current code.
Agreed. Current handling of enable pin isn't right.
However, see below regarding the floating backlight enable pin.
quoted
quoted
quoted
This patch does not change the assumption that we can configure the
GPIO before we modify the PWM state. This means it won't fix the problem
for cases there the pin is HiZ by default but whose GPIOD_ASIS state is
neither input nor output.
That is correct, for pin that is floating, we lost. But then I would argue
that if your backlight-enable GPIO is floating, the hardware is buggy, I
would expect some pull resistor to keep the backlight off on power on on
that GPIO.
I didn't say that the pin was floating. I said that the pin was in a HiZ
state meaning it could still be subject to pull up/down.
However there are cases, such as when the regulator is off, where I
think it is entirely legitimate for the enable pin to be floating. The
current driver does the wrong thing here if the pin is set as input
since if the regulator is off the initial enable_gpio value should be 0.
Oh, right, that's a valid point.
So if the pin is input, we can basically toss a coin.
I don't think it is quite as bad as that: if the PWM and regulator
are enabled then it is not okay for this pin to be floating.
quoted
[...]
I think a reasonably elegant approach can be reached by making
pwm_backlight_initial_power_state() responsible for ensuring enable_gpio
matches the observed hardware state (taking into account both the pin
state and the regulator). I think this will fix both your flicker
concerns whilst permitting the legitimate cases for a floating pin.
Something like:
I think we are getting closer, but there is extra problem to this.
This will fail on iMX GPIO controller, where if the GPIO is output, you can
read its state, but by default that state is what you wrote into the GPIO
output value register, not what is the actual value on the pin (i.e.
consider you have a strong pull resistor that overpowers the driver).
To have a GPIO which is output and sample the actual pin value, you have to
tweak the pinmux and enable the SION bit, then you get the actual value. But
that is specific to the iMX GPIO controller/pinmux.
You're describing a situation where we own a GPIO output pin and the
value we believe we are driving into the pin is not being achieved due
to some additional factor. Do we need to care about that? It sounds like
the backlight driver won't work properly in this case since whatever
value we set the enable_gpio then it will stay at the same value.
quoted
[...]
@@ -486,18 +500,6 @@ static int pwm_backlight_probe(struct platform_device *pdev) goto err_alloc; }- /*- * If the GPIO is not known to be already configured as output, that- * is, if gpiod_get_direction returns either 1 or -EINVAL, change the- * direction to output and set the GPIO as active.- * Do not force the GPIO to active when it was already output as it- * could cause backlight flickering or we would enable the backlight too- * early. Leave the decision of the initial backlight state for later.- */- if (pb->enable_gpio &&- gpiod_get_direction(pb->enable_gpio) != 0)- gpiod_direction_output(pb->enable_gpio, 1);
pwm_backlight_initial_power_state() is still called after pwm_apply_state()
in pwm_backlight_probe(), so that might still be too late, no ?
The initial pwm_apply_state() is essentially a nop or, perhaps, a sanity
check if you prefer to think if it that way.
It can change the PWM period in some (non-DT) cases but only if the PWM
is not already running... and the change of period should not start it
running.
Daniel.
From: Marek Vasut <marex@denx.de> Date: 2021-07-21 18:46:47
On 7/21/21 6:12 PM, Daniel Thompson wrote:
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 12:49 PM, Daniel Thompson wrote:
quoted
quoted
I'm not sure that's correct, we can simply say that any new uses of the
pwm-backlight should specify the initial GPIO configuration, and for the
legacy ones, use whatever is in the code now.
I'm not 100% against the idea... however if we still have to get the
code to read state from the hardware right for legacy cases that means
we have to do the same work but with fewer people testing it.
We can do something like this:
if (of_property_read_bool(np, "enable-active-high"))
gpiod_direction_output(pb->enable_gpio, 1);
else if (of_property_read_bool(np, "enable-active-low"))
gpiod_direction_output(pb->enable_gpio, 0);
else {
WARN_ON_ONCE("Fix your DT"); // or some such notification
... legacy code path ...
}
Note that I picked the same DT prop names as drivers/gpio/gpiolib-of.c
of_gpio_flags_quirks() uses, because we are headed into similar mess here
I'm afraid.
I don't quite understand what you mean here. We are using gpiolib so
for us there is no concept of active-high or active-low. The only
concept for us is whether enable_gpio is asserted or not.
It would look the same -- just substitute in "enable-on-boot" and
"disable-on-boot" DT property.
What the DT property would be describing is purely whether the
bootloader left the backlight on or off.
Rather, it would simply control what is the default state of the
backlight enable GPIO (enabled/disabled).
This sails very close to the
edge of what is in-scope for DT (at least it does it we can read
the inherited state directly from the hardware).
The problem with reading it out of hardware is that the hardware might
be in undefined state and expects Linux to define that state, so that
does not always work. Hence my initial suggestion to add a DT property
to define the state up front, instead of using these fragile heuristics.
What it also means decisions about the DT bindings are more about
whether, if the backlight is lit up, the bootloader should also disclose
what it thinks it has established as the PWM duty cycle as well.
Please also consider the case where bootloader configures total minimum
of the hardware to start Linux as soon as possible, i.e. it puts Linux
in DRAM and jumps to Linux.
Overall I have fairly grave concerns that this simply moves
fragility into the bootloader rather then reducing it.
Wait a minute, I think we disconnected somewhere. I would rather prefer
to remove the fragility and bootloader dependency altogether, exactly to
avoid depending on the state the bootloader left the hardware in.
From: Marek Vasut <marex@denx.de> Date: 2021-07-21 19:01:05
On 7/21/21 6:43 PM, Daniel Thompson wrote:
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 12:49 PM, Daniel Thompson wrote:
quoted
quoted
quoted
However, on the basis of making things less fragile, I think the
underlying problem here is the assumption that it is safe to modify
enable_gpio before the driver has imposed state upon the PWM (this
assumption has always been made and, in addition to systems where the BL
has a phandle will also risks flicker problems on systems where
power_pwm_on_delay is not zero).
It is safe to modify the GPIO into defined state, but that defined state is
not always out/enabled, that defined state depends on the hardware.
It is only safe to do this once we know what the initial value should be
and I'm not sure that value can comes exclusively from reading the pin.
I agree, it is far from perfect, but so is the current code.
Agreed. Current handling of enable pin isn't right.
quoted
However, see below regarding the floating backlight enable pin.
quoted
quoted
quoted
This patch does not change the assumption that we can configure the
GPIO before we modify the PWM state. This means it won't fix the problem
for cases there the pin is HiZ by default but whose GPIOD_ASIS state is
neither input nor output.
That is correct, for pin that is floating, we lost. But then I would argue
that if your backlight-enable GPIO is floating, the hardware is buggy, I
would expect some pull resistor to keep the backlight off on power on on
that GPIO.
I didn't say that the pin was floating. I said that the pin was in a HiZ
state meaning it could still be subject to pull up/down.
However there are cases, such as when the regulator is off, where I
think it is entirely legitimate for the enable pin to be floating. The
current driver does the wrong thing here if the pin is set as input
since if the regulator is off the initial enable_gpio value should be 0.
Oh, right, that's a valid point.
So if the pin is input, we can basically toss a coin.
I don't think it is quite as bad as that: if the PWM and regulator
are enabled then it is not okay for this pin to be floating.
So then we would have to check the regulator and pwm state, however
Linux driver for those can reinit both the regulator and pwm block, so
we are growing more and more heuristics.
quoted
quoted
[...]
I think a reasonably elegant approach can be reached by making
pwm_backlight_initial_power_state() responsible for ensuring enable_gpio
matches the observed hardware state (taking into account both the pin
state and the regulator). I think this will fix both your flicker
concerns whilst permitting the legitimate cases for a floating pin.
Something like:
I think we are getting closer, but there is extra problem to this.
This will fail on iMX GPIO controller, where if the GPIO is output, you can
read its state, but by default that state is what you wrote into the GPIO
output value register, not what is the actual value on the pin (i.e.
consider you have a strong pull resistor that overpowers the driver).
To have a GPIO which is output and sample the actual pin value, you have to
tweak the pinmux and enable the SION bit, then you get the actual value. But
that is specific to the iMX GPIO controller/pinmux.
You're describing a situation where we own a GPIO output pin and the
value we believe we are driving into the pin is not being achieved due
to some additional factor.
E.g. disabled PWM or regulator.
Do we need to care about that? It sounds like
the backlight driver won't work properly in this case since whatever
value we set the enable_gpio then it will stay at the same value.
Possibly.
quoted
quoted
[...]
@@ -486,18 +500,6 @@ static int pwm_backlight_probe(struct platform_device *pdev) goto err_alloc; }- /*- * If the GPIO is not known to be already configured as output, that- * is, if gpiod_get_direction returns either 1 or -EINVAL, change the- * direction to output and set the GPIO as active.- * Do not force the GPIO to active when it was already output as it- * could cause backlight flickering or we would enable the backlight too- * early. Leave the decision of the initial backlight state for later.- */- if (pb->enable_gpio &&- gpiod_get_direction(pb->enable_gpio) != 0)- gpiod_direction_output(pb->enable_gpio, 1);
pwm_backlight_initial_power_state() is still called after pwm_apply_state()
in pwm_backlight_probe(), so that might still be too late, no ?
The initial pwm_apply_state() is essentially a nop or, perhaps, a sanity
check if you prefer to think if it that way.
It can change the PWM period in some (non-DT) cases but only if the PWM
is not already running... and the change of period should not start it
running.
From: Marek Vasut <marex@denx.de> Date: 2021-07-21 20:10:31
On 7/21/21 9:01 PM, Marek Vasut wrote:
[...]
quoted
quoted
quoted
@@ -486,18 +500,6 @@ static int pwm_backlight_probe(struct
platform_device *pdev)
goto err_alloc;
}
- /*
- * If the GPIO is not known to be already configured as output,
that
- * is, if gpiod_get_direction returns either 1 or -EINVAL,
change the
- * direction to output and set the GPIO as active.
- * Do not force the GPIO to active when it was already output
as it
- * could cause backlight flickering or we would enable the
backlight too
- * early. Leave the decision of the initial backlight state for
later.
- */
- if (pb->enable_gpio &&
- gpiod_get_direction(pb->enable_gpio) != 0)
- gpiod_direction_output(pb->enable_gpio, 1);
pwm_backlight_initial_power_state() is still called after
pwm_apply_state()
in pwm_backlight_probe(), so that might still be too late, no ?
The initial pwm_apply_state() is essentially a nop or, perhaps, a sanity
check if you prefer to think if it that way.
It can change the PWM period in some (non-DT) cases but only if the PWM
is not already running... and the change of period should not start it
running.
All right, let me give this a try.
ACK, for this case I have here, this works too. Can you submit a proper
patch, including my AB/TB and I think also the Fixes tag ?
From: Daniel Thompson <hidden> Date: 2021-07-22 11:28:29
On Wed, Jul 21, 2021 at 08:46:42PM +0200, Marek Vasut wrote:
On 7/21/21 6:12 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 12:49 PM, Daniel Thompson wrote:
quoted
quoted
I'm not sure that's correct, we can simply say that any new uses of the
pwm-backlight should specify the initial GPIO configuration, and for the
legacy ones, use whatever is in the code now.
I'm not 100% against the idea... however if we still have to get the
code to read state from the hardware right for legacy cases that means
we have to do the same work but with fewer people testing it.
We can do something like this:
if (of_property_read_bool(np, "enable-active-high"))
gpiod_direction_output(pb->enable_gpio, 1);
else if (of_property_read_bool(np, "enable-active-low"))
gpiod_direction_output(pb->enable_gpio, 0);
else {
WARN_ON_ONCE("Fix your DT"); // or some such notification
... legacy code path ...
}
Note that I picked the same DT prop names as drivers/gpio/gpiolib-of.c
of_gpio_flags_quirks() uses, because we are headed into similar mess here
I'm afraid.
I don't quite understand what you mean here. We are using gpiolib so
for us there is no concept of active-high or active-low. The only
concept for us is whether enable_gpio is asserted or not.
It would look the same -- just substitute in "enable-on-boot" and
"disable-on-boot" DT property.
quoted
What the DT property would be describing is purely whether the
bootloader left the backlight on or off.
Rather, it would simply control what is the default state of the backlight
enable GPIO (enabled/disabled).
What do you mean by default state? The current value of the pin or the
desired state when the probe completes?
quoted
This sails very close to the
edge of what is in-scope for DT (at least it does it we can read
the inherited state directly from the hardware).
The problem with reading it out of hardware is that the hardware might be in
undefined state and expects Linux to define that state, so that does not
always work. Hence my initial suggestion to add a DT property to define the
state up front, instead of using these fragile heuristics.
To achieve a flicker-free boot we must know the initial state of the
backlight (not just the enable pin).
quoted
What it also means decisions about the DT bindings are more about
whether, if the backlight is lit up, the bootloader should also disclose
what it thinks it has established as the PWM duty cycle as well.
Please also consider the case where bootloader configures total minimum of
the hardware to start Linux as soon as possible, i.e. it puts Linux in DRAM
and jumps to Linux.
I think I have been. I understood that preventing a flicker when booting
with an unconfigured (and off) backlight[1] was the purpose of your patch!
However that is a relatively easy case when considering flicker-free
handover from bootloader since we don't have to inherit the duty cycle.
[1] I guessed that the difference between your platform and the other
pwm_bl users is that, for you, an uninitialized PWM looks like a
100% duty cycle hence you get a full-brightness flicker when we change
the state of the enable_gpio pin before we have established the
correct PWM duty cycle. Was I right?
quoted
Overall I have fairly grave concerns that this simply moves
fragility into the bootloader rather then reducing it.
Wait a minute, I think we disconnected somewhere. I would rather prefer to
remove the fragility and bootloader dependency altogether, exactly to avoid
depending on the state the bootloader left the hardware in.
The two fully flicker-free cases we support in pwm_bl are:
1. Backlight off after bootloader has completed. Backlight must be
off after the probe completes (and never flicker on/off during the
probe). This allows the display to put a splash image on the screen
before lighting up the backlight (this avoids a flicker if there are
a few frames between backlight coming on and the splash image being
drawn). Naturally this requires help from the display system (and
that the display system is aware of the backlight to be able to start
it).
2. Backlight on with a splash image after bootloader has completed.
Backlight must be on after the probe completes (and never flicker
off/on during the probe). This also requires that the display system
can take over the frame buffer without a flicker but that is
completely independent of backlight.
There is also a simpler case which is not "flicker-free" since the
backlight may change level during the boot and may light up before
there is an image on the screen (although we'd still to minimise
flicker by ensuring there is only one change of backlight state/level
during the probe (something your work will see fixed?):
3. Backlight is on after the probe completes. This is default if
we don't know the display system will activate the backlight.
This is an important legacy case since few userspaces know how
to change the backlight power-state at boot.
One oddity here is that #3 *also* needs to know the state of the
backlight (on/off) to turn the backlight on without flickering
(so it can figure out how to handle power_pwm_on_delay correctly)
even though the final state is unconditionally on. That is the main
reason I proposed an alternative to your patch (since this is
currently broken).
The other oddity is that the difference between #1 and #3 is due to
*software* (which driver ends up responsible for unmuting the display)
meaning that the bootloader/DT has no business discriminating between
these two cases.
Thus pwm_bl.c is based on making #2/#3 (which are similar) the default
and switching to case #1 if there is a display driver to do the unblank
(software) *and* that the backlight is currently off (currently read
from hardware). Note that this is intentionally designed to that
if the logic does go wrong we should get a small bug (a flicker) rather
than a big one (a black screen).
Wow! That is *way* longer than I intended when I started writing it.
Anyhow I suspect any disconnect comes about due to the difference in
backlight state *after* probe being, in part, to software structure
rather than purely a hardware property.
Daniel.
From: Marek Vasut <marex@denx.de> Date: 2021-07-22 19:03:00
On 7/22/21 1:28 PM, Daniel Thompson wrote:
On Wed, Jul 21, 2021 at 08:46:42PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 6:12 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 12:49 PM, Daniel Thompson wrote:
quoted
quoted
I'm not sure that's correct, we can simply say that any new uses of the
pwm-backlight should specify the initial GPIO configuration, and for the
legacy ones, use whatever is in the code now.
I'm not 100% against the idea... however if we still have to get the
code to read state from the hardware right for legacy cases that means
we have to do the same work but with fewer people testing it.
We can do something like this:
if (of_property_read_bool(np, "enable-active-high"))
gpiod_direction_output(pb->enable_gpio, 1);
else if (of_property_read_bool(np, "enable-active-low"))
gpiod_direction_output(pb->enable_gpio, 0);
else {
WARN_ON_ONCE("Fix your DT"); // or some such notification
... legacy code path ...
}
Note that I picked the same DT prop names as drivers/gpio/gpiolib-of.c
of_gpio_flags_quirks() uses, because we are headed into similar mess here
I'm afraid.
I don't quite understand what you mean here. We are using gpiolib so
for us there is no concept of active-high or active-low. The only
concept for us is whether enable_gpio is asserted or not.
It would look the same -- just substitute in "enable-on-boot" and
"disable-on-boot" DT property.
quoted
What the DT property would be describing is purely whether the
bootloader left the backlight on or off.
Rather, it would simply control what is the default state of the backlight
enable GPIO (enabled/disabled).
What do you mean by default state? The current value of the pin or the
desired state when the probe completes?
I think that would be the later.
quoted
quoted
This sails very close to the
edge of what is in-scope for DT (at least it does it we can read
the inherited state directly from the hardware).
The problem with reading it out of hardware is that the hardware might be in
undefined state and expects Linux to define that state, so that does not
always work. Hence my initial suggestion to add a DT property to define the
state up front, instead of using these fragile heuristics.
To achieve a flicker-free boot we must know the initial state of the
backlight (not just the enable pin).
The backlight hardware might be in uninitialized state and then Linux
should set the state, likely based on something in DT, because there is
no previous state to read.
quoted
quoted
What it also means decisions about the DT bindings are more about
whether, if the backlight is lit up, the bootloader should also disclose
what it thinks it has established as the PWM duty cycle as well.
Please also consider the case where bootloader configures total minimum of
the hardware to start Linux as soon as possible, i.e. it puts Linux in DRAM
and jumps to Linux.
I think I have been. I understood that preventing a flicker when booting
with an unconfigured (and off) backlight[1] was the purpose of your patch!
However that is a relatively easy case when considering flicker-free
handover from bootloader since we don't have to inherit the duty cycle.
[1] I guessed that the difference between your platform and the other
pwm_bl users is that, for you, an uninitialized PWM looks like a
100% duty cycle hence you get a full-brightness flicker when we change
the state of the enable_gpio pin before we have established the
correct PWM duty cycle. Was I right?
Right, that. In my case the enable GPIO is input (default) with pull
resistor.
quoted
quoted
Overall I have fairly grave concerns that this simply moves
fragility into the bootloader rather then reducing it.
Wait a minute, I think we disconnected somewhere. I would rather prefer to
remove the fragility and bootloader dependency altogether, exactly to avoid
depending on the state the bootloader left the hardware in.
The two fully flicker-free cases we support in pwm_bl are:
1. Backlight off after bootloader has completed. Backlight must be
off after the probe completes (and never flicker on/off during the
probe). This allows the display to put a splash image on the screen
before lighting up the backlight (this avoids a flicker if there are
a few frames between backlight coming on and the splash image being
drawn). Naturally this requires help from the display system (and
that the display system is aware of the backlight to be able to start
it).
2. Backlight on with a splash image after bootloader has completed.
Backlight must be on after the probe completes (and never flicker
off/on during the probe). This also requires that the display system
can take over the frame buffer without a flicker but that is
completely independent of backlight.
There is also a simpler case which is not "flicker-free" since the
backlight may change level during the boot and may light up before
there is an image on the screen (although we'd still to minimise
flicker by ensuring there is only one change of backlight state/level
during the probe (something your work will see fixed?):
Actually no, my usecase is the backlight is not initialized by the
bootloader at all, the pins are just strapped to default to the right
values, the init is left to the kernel to do.
3. Backlight is on after the probe completes. This is default if
we don't know the display system will activate the backlight.
This is an important legacy case since few userspaces know how
to change the backlight power-state at boot.
One oddity here is that #3 *also* needs to know the state of the
backlight (on/off) to turn the backlight on without flickering
(so it can figure out how to handle power_pwm_on_delay correctly)
even though the final state is unconditionally on. That is the main
reason I proposed an alternative to your patch (since this is
currently broken).
The other oddity is that the difference between #1 and #3 is due to
*software* (which driver ends up responsible for unmuting the display)
meaning that the bootloader/DT has no business discriminating between
these two cases.
Thus pwm_bl.c is based on making #2/#3 (which are similar) the default
and switching to case #1 if there is a display driver to do the unblank
(software) *and* that the backlight is currently off (currently read
from hardware). Note that this is intentionally designed to that
if the logic does go wrong we should get a small bug (a flicker) rather
than a big one (a black screen).
Wow! That is *way* longer than I intended when I started writing it.
Anyhow I suspect any disconnect comes about due to the difference in
backlight state *after* probe being, in part, to software structure
rather than purely a hardware property.
From: Daniel Thompson <hidden> Date: 2021-07-23 10:15:17
On Thu, Jul 22, 2021 at 09:02:04PM +0200, Marek Vasut wrote:
On 7/22/21 1:28 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 08:46:42PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 6:12 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 12:49 PM, Daniel Thompson wrote:
[...]
This sails very close to the
edge of what is in-scope for DT (at least it does it we can read
the inherited state directly from the hardware).
The problem with reading it out of hardware is that the hardware might be in
undefined state and expects Linux to define that state, so that does not
always work. Hence my initial suggestion to add a DT property to define the
state up front, instead of using these fragile heuristics.
To achieve a flicker-free boot we must know the initial state of the
backlight (not just the enable pin).
The backlight hardware might be in uninitialized state and then Linux should
set the state, likely based on something in DT, because there is no previous
state to read.
There is always a previous state. The kernel doesn't care whether that
previous state was imposed by a power-on reset, the bootloader or a
kexec.
For the driver to come up flicker-free in all the different cases we
need to know whether the backlight is currently emitting light or not
and, if it is emitting light, then we need to know what the duty cycle
is (currently we inherit require the PWM driver to correctly inherit the
duty cycle from the hardware).
So far, the previous state has been observable by the lower level
drivers (GPIO, PWM, regulator). I remain reluctant to provide
workarounds for cases where it is not observable without motivating
hardware. I certainly wouldn't want to make such bindings mandatory
since observable hardware registers are a far more reliable source of
truth than what the DT tells us about what it thinks the bootloader
(or power-on reset) actually did ;-).
quoted
quoted
quoted
Overall I have fairly grave concerns that this simply moves
fragility into the bootloader rather then reducing it.
Wait a minute, I think we disconnected somewhere. I would rather prefer to
remove the fragility and bootloader dependency altogether, exactly to avoid
depending on the state the bootloader left the hardware in.
The two fully flicker-free cases we support in pwm_bl are:
1. Backlight off after bootloader has completed. Backlight must be
off after the probe completes (and never flicker on/off during the
probe). This allows the display to put a splash image on the screen
before lighting up the backlight (this avoids a flicker if there are
a few frames between backlight coming on and the splash image being
drawn). Naturally this requires help from the display system (and
that the display system is aware of the backlight to be able to start
it).
2. Backlight on with a splash image after bootloader has completed.
Backlight must be on after the probe completes (and never flicker
off/on during the probe). This also requires that the display system
can take over the frame buffer without a flicker but that is
completely independent of backlight.
There is also a simpler case which is not "flicker-free" since the
backlight may change level during the boot and may light up before
there is an image on the screen (although we'd still to minimise
flicker by ensuring there is only one change of backlight state/level
during the probe (something your work will see fixed?):
Actually no, my usecase is the backlight is not initialized by the
bootloader at all, the pins are just strapped to default to the right
values, the init is left to the kernel to do.
It doesn't matter to us who established the initial state. In this case
the backlight is off at handover. That means you are either case #1
(display system will unblank" the backlight automatically when the reset
of the display unblanks) or #3 (BL driver will "unblank" the backlight
during the probe).
Your changes should result in a fix to both these cases!
quoted
3. Backlight is on after the probe completes. This is default if
we don't know the display system will activate the backlight.
This is an important legacy case since few userspaces know how
to change the backlight power-state at boot.
One oddity here is that #3 *also* needs to know the state of the
backlight (on/off) to turn the backlight on without flickering
(so it can figure out how to handle power_pwm_on_delay correctly)
even though the final state is unconditionally on. That is the main
reason I proposed an alternative to your patch (since this is
currently broken).
The other oddity is that the difference between #1 and #3 is due to
*software* (which driver ends up responsible for unmuting the display)
meaning that the bootloader/DT has no business discriminating between
these two cases.
Thus pwm_bl.c is based on making #2/#3 (which are similar) the default
and switching to case #1 if there is a display driver to do the unblank
(software) *and* that the backlight is currently off (currently read
from hardware). Note that this is intentionally designed to that
if the logic does go wrong we should get a small bug (a flicker) rather
than a big one (a black screen).
Wow! That is *way* longer than I intended when I started writing it.
Anyhow I suspect any disconnect comes about due to the difference in
backlight state *after* probe being, in part, to software structure
rather than purely a hardware property.
From: Daniel Thompson <hidden> Date: 2021-07-23 11:17:30
On Fri, Jul 23, 2021 at 11:15:10AM +0100, Daniel Thompson wrote:
On Thu, Jul 22, 2021 at 09:02:04PM +0200, Marek Vasut wrote:
quoted
On 7/22/21 1:28 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 08:46:42PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 6:12 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 12:49 PM, Daniel Thompson wrote:
[...]
This sails very close to the
edge of what is in-scope for DT (at least it does it we can read
the inherited state directly from the hardware).
The problem with reading it out of hardware is that the hardware might be in
undefined state and expects Linux to define that state, so that does not
always work. Hence my initial suggestion to add a DT property to define the
state up front, instead of using these fragile heuristics.
To achieve a flicker-free boot we must know the initial state of the
backlight (not just the enable pin).
The backlight hardware might be in uninitialized state and then Linux should
set the state, likely based on something in DT, because there is no previous
state to read.
There is always a previous state. The kernel doesn't care whether that
previous state was imposed by a power-on reset, the bootloader or a
kexec.
For the driver to come up flicker-free in all the different cases we
need to know whether the backlight is currently emitting light or not
and, if it is emitting light, then we need to know what the duty cycle
is (currently we inherit require the PWM driver to correctly inherit the
duty cycle from the hardware).
Oops... this is wrong (I think it is cross-talk from an old patch). We
do not currently inherit the duty cycle.
So far, the previous state has been observable by the lower level
drivers (GPIO, PWM, regulator). I remain reluctant to provide
workarounds for cases where it is not observable without motivating
hardware. I certainly wouldn't want to make such bindings mandatory
since observable hardware registers are a far more reliable source of
truth than what the DT tells us about what it thinks the bootloader
(or power-on reset) actually did ;-).
Which makes conclusion badly reasoned.
However, until we can clearly articulate whether the problem we want to
solve is describing the initial backlight state or specifying the default
(post-probe) power state for the legacy cases I'm still content not to
change things ;-).
quoted
quoted
[...]
Wow! That is *way* longer than I intended when I started writing it.
Anyhow I suspect any disconnect comes about due to the difference in
backlight state *after* probe being, in part, to software structure
rather than purely a hardware property.
Maybe this should be added to documentation.
I'll see what I can do.
Done, see v3. I think it is better explained than the e-mail version.
Daniel.
From: Marek Vasut <marex@denx.de> Date: 2021-07-23 12:27:32
On 7/23/21 1:17 PM, Daniel Thompson wrote:
On Fri, Jul 23, 2021 at 11:15:10AM +0100, Daniel Thompson wrote:
quoted
On Thu, Jul 22, 2021 at 09:02:04PM +0200, Marek Vasut wrote:
quoted
On 7/22/21 1:28 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 08:46:42PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 6:12 PM, Daniel Thompson wrote:
quoted
On Wed, Jul 21, 2021 at 05:09:57PM +0200, Marek Vasut wrote:
quoted
On 7/21/21 12:49 PM, Daniel Thompson wrote:
[...]
This sails very close to the
edge of what is in-scope for DT (at least it does it we can read
the inherited state directly from the hardware).
The problem with reading it out of hardware is that the hardware might be in
undefined state and expects Linux to define that state, so that does not
always work. Hence my initial suggestion to add a DT property to define the
state up front, instead of using these fragile heuristics.
To achieve a flicker-free boot we must know the initial state of the
backlight (not just the enable pin).
The backlight hardware might be in uninitialized state and then Linux should
set the state, likely based on something in DT, because there is no previous
state to read.
There is always a previous state. The kernel doesn't care whether that
previous state was imposed by a power-on reset, the bootloader or a
kexec.
For the driver to come up flicker-free in all the different cases we
need to know whether the backlight is currently emitting light or not
and, if it is emitting light, then we need to know what the duty cycle
is (currently we inherit require the PWM driver to correctly inherit the
duty cycle from the hardware).
Oops... this is wrong (I think it is cross-talk from an old patch). We
do not currently inherit the duty cycle.
There is that, and if you did, you would be telling PWM drivers not to
reset/reinit the hardware in probe. I'm not sure whether that is a good
idea.
quoted
So far, the previous state has been observable by the lower level
drivers (GPIO, PWM, regulator). I remain reluctant to provide
workarounds for cases where it is not observable without motivating
hardware. I certainly wouldn't want to make such bindings mandatory
since observable hardware registers are a far more reliable source of
truth than what the DT tells us about what it thinks the bootloader
(or power-on reset) actually did ;-).
Which makes conclusion badly reasoned.
However, until we can clearly articulate whether the problem we want to
solve is describing the initial backlight state or specifying the default
(post-probe) power state for the legacy cases I'm still content not to
change things ;-).
For me, it was always about specifying well defined default state of the
backlight.
quoted
quoted
quoted
[...]
Wow! That is *way* longer than I intended when I started writing it.
Anyhow I suspect any disconnect comes about due to the difference in
backlight state *after* probe being, in part, to software structure
rather than purely a hardware property.
Maybe this should be added to documentation.
I'll see what I can do.
Done, see v3. I think it is better explained than the e-mail version.