[PATCH 0/3] atmel_lcdfb: fix 16-bpp regression

STALE4954d

Revision v1 of 2 in this series.

18 messages, 2 authors, 2013-02-07 · open the first message on its own page

[PATCH 0/3] atmel_lcdfb: fix 16-bpp regression

From: Johan Hovold <hidden>
Date: 2012-12-10 12:28:47 

These patches fix a regression in 16-bpp support for older SOCs which use
IBGR:555 rather than BGR:565 pixel layout. Use SOC-type to determine if the
controller uses the intensity-bit and restore the old layout in that case.

The third patch is simply a clean up.

Thanks,
Johan

Johan Hovold (3):
  atmel_lcdfb: fix 16-bpp modes on older SOCs
  ARM: at91/neocore926: fix LCD-wiring mode
  atmel_lcdfb: remove unsupported 15-bpp mode

 arch/arm/mach-at91/board-neocore926.c |  2 +-
 drivers/video/atmel_lcdfb.c           | 23 +++++++++++++++--------
 include/video/atmel_lcdc.h            |  2 +-
 3 files changed, 17 insertions(+), 10 deletions(-)

-- 
1.8.0

[PATCH 1/3] atmel_lcdfb: fix 16-bpp modes on older SOCs

From: Johan Hovold <hidden>
Date: 2012-12-10 12:28:48 

Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.

Use SOC-type to determine the pixel layout.

Tested on custom at91sam9263-board.

Cc: <redacted>
Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 22 +++++++++++++++-------
 include/video/atmel_lcdc.h  |  1 +
 2 files changed, 16 insertions(+), 7 deletions(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 1505539..1f68fa6 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -422,17 +422,22 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
 			= var->bits_per_pixel;
 		break;
 	case 16:
+		/* Older SOCs use IBGR:555 rather than BGR:565. */
+		if (sinfo->have_intensity_bit)
+			var->green.length = 5;
+		else
+			var->green.length = 6;
+
 		if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
-			/* RGB:565 mode */
-			var->red.offset = 11;
+			/* RGB:5X5 mode */
+			var->red.offset = var->green.length + 5;
 			var->blue.offset = 0;
 		} else {
-			/* BGR:565 mode */
+			/* BGR:5X5 mode */
 			var->red.offset = 0;
-			var->blue.offset = 11;
+			var->blue.offset = var->green.length + 5;
 		}
 		var->green.offset = 5;
-		var->green.length = 6;
 		var->red.length = var->blue.length = 5;
 		break;
 	case 32:
@@ -679,8 +684,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
 
 	case FB_VISUAL_PSEUDOCOLOR:
 		if (regno < 256) {
-			if (cpu_is_at91sam9261() || cpu_is_at91sam9263()
-			    || cpu_is_at91sam9rl()) {
+			if (sinfo->have_intensity_bit) {
 				/* old style I+BGR:555 */
 				val  = ((red   >> 11) & 0x001f);
 				val |= ((green >>  6) & 0x03e0);
@@ -870,6 +874,10 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	}
 	sinfo->info = info;
 	sinfo->pdev = pdev;
+	if (cpu_is_at91sam9261() || cpu_is_at91sam9263() ||
+							cpu_is_at91sam9rl()) {
+		sinfo->have_intensity_bit = true;
+	}
 
 	strcpy(info->fix.id, sinfo->pdev->name);
 	info->flags = ATMEL_LCDFB_FBINFO_DEFAULT;
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 28447f1..5f0e234 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -62,6 +62,7 @@ struct atmel_lcdfb_info {
 	void (*atmel_lcdfb_power_control)(int on);
 	struct fb_monspecs	*default_monspecs;
 	u32			pseudo_palette[16];
+	bool			have_intensity_bit;
 };
 
 #define ATMEL_LCDC_DMABADDR1	0x00
-- 
1.8.0

[PATCH 2/3] ARM: at91/neocore926: fix LCD-wiring mode

From: Johan Hovold <hidden>
Date: 2012-12-10 12:28:49 

Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather than
BGR:565.

The above commit also removed the RGB:555-wiring hack without fixing the
neocore926 board which used it. Fix by specifying RGB-wiring and let the
driver handle the final SOC-dependant layout.

Remove the no longer used ATMEL_LCDC_WIRING_RGB555 define.

Compile-only tested.

Cc: <redacted>
Signed-off-by: Johan Hovold <redacted>
---
 arch/arm/mach-at91/board-neocore926.c | 2 +-
 include/video/atmel_lcdc.h            | 1 -
 2 files changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
index 997d359..daeb7c6 100644
--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -265,7 +265,7 @@ static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = {
 	.default_monspecs		= &at91fb_default_monspecs,
 	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
 	.guard_time			= 1,
-	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB555,
+	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB,
 };
 
 #else
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 5f0e234..8deb226 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -30,7 +30,6 @@
  */
 #define ATMEL_LCDC_WIRING_BGR	0
 #define ATMEL_LCDC_WIRING_RGB	1
-#define ATMEL_LCDC_WIRING_RGB555	2
 
 
  /* LCD Controller info data structure, stored in device platform_data */
-- 
1.8.0

[PATCH 3/3] atmel_lcdfb: remove unsupported 15-bpp mode

From: Johan Hovold <hidden>
Date: 2012-12-10 12:28:50 

Since commit 787f9fd23283 ("atmel_lcdfb: support 16bit BGR:565 mode,
remove unsupported 15bit modes") atmel_lcdfb_check_var does not accept
15-bpp mode so remove it from atmel_lcdfb_set_par as well.

Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 1f68fa6..3cdbd53 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -567,7 +567,6 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
 		case 2: value |= ATMEL_LCDC_PIXELSIZE_2; break;
 		case 4: value |= ATMEL_LCDC_PIXELSIZE_4; break;
 		case 8: value |= ATMEL_LCDC_PIXELSIZE_8; break;
-		case 15: /* fall through */
 		case 16: value |= ATMEL_LCDC_PIXELSIZE_16; break;
 		case 24: value |= ATMEL_LCDC_PIXELSIZE_24; break;
 		case 32: value |= ATMEL_LCDC_PIXELSIZE_32; break;
-- 
1.8.0

[PATCH 0/3] atmel_lcdfb: fix 16-bpp regression

From: Johan Hovold <hidden>
Date: 2013-01-26 15:44:15 

On Mon, Dec 10, 2012 at 01:28:47PM +0100, Johan Hovold wrote:
These patches fix a regression in 16-bpp support for older SOCs which use
IBGR:555 rather than BGR:565 pixel layout. Use SOC-type to determine if the
controller uses the intensity-bit and restore the old layout in that case.
I understand the maintainer's been busy lately, but could someone pick
these regression fixes up so we can get them into v3.8-rc and the stable
trees?

Thanks,
Johan

[PATCH 1/3] atmel_lcdfb: fix 16-bpp modes on older SOCs

From: Jean-Christophe PLAGNIOL-VILLARD <hidden>
Date: 2013-01-29 13:54:35 

On 13:28 Mon 10 Dec     , Johan Hovold wrote:
quoted hunk
Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.

Use SOC-type to determine the pixel layout.

Tested on custom at91sam9263-board.

Cc: <redacted>
Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 22 +++++++++++++++-------
 include/video/atmel_lcdc.h  |  1 +
 2 files changed, 16 insertions(+), 7 deletions(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 1505539..1f68fa6 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -422,17 +422,22 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
 			= var->bits_per_pixel;
 		break;
 	case 16:
+		/* Older SOCs use IBGR:555 rather than BGR:565. */
+		if (sinfo->have_intensity_bit)
+			var->green.length = 5;
+		else
+			var->green.length = 6;
+
 		if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
-			/* RGB:565 mode */
-			var->red.offset = 11;
+			/* RGB:5X5 mode */
+			var->red.offset = var->green.length + 5;
 			var->blue.offset = 0;
 		} else {
-			/* BGR:565 mode */
+			/* BGR:5X5 mode */
 			var->red.offset = 0;
-			var->blue.offset = 11;
+			var->blue.offset = var->green.length + 5;
 		}
 		var->green.offset = 5;
-		var->green.length = 6;
 		var->red.length = var->blue.length = 5;
 		break;
 	case 32:
@@ -679,8 +684,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
 
 	case FB_VISUAL_PSEUDOCOLOR:
 		if (regno < 256) {
-			if (cpu_is_at91sam9261() || cpu_is_at91sam9263()
-			    || cpu_is_at91sam9rl()) {
+			if (sinfo->have_intensity_bit) {
 				/* old style I+BGR:555 */
 				val  = ((red   >> 11) & 0x001f);
 				val |= ((green >>  6) & 0x03e0);
@@ -870,6 +874,10 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	}
 	sinfo->info = info;
 	sinfo->pdev = pdev;
+	if (cpu_is_at91sam9261() || cpu_is_at91sam9263() ||
+							cpu_is_at91sam9rl()) {
+		sinfo->have_intensity_bit = true;
+	}
nack

you need to drop the cpu_is as this can only be use now for the core

use platform_device_id to indetify the IP as done on at91-i2c as we can not
detect the IP version

Best Regards,
J.
quoted hunk
 
 	strcpy(info->fix.id, sinfo->pdev->name);
 	info->flags = ATMEL_LCDFB_FBINFO_DEFAULT;
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 28447f1..5f0e234 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -62,6 +62,7 @@ struct atmel_lcdfb_info {
 	void (*atmel_lcdfb_power_control)(int on);
 	struct fb_monspecs	*default_monspecs;
 	u32			pseudo_palette[16];
+	bool			have_intensity_bit;
 };
 
 #define ATMEL_LCDC_DMABADDR1	0x00
-- 
1.8.0

[PATCH 1/3] atmel_lcdfb: fix 16-bpp modes on older SOCs

From: Johan Hovold <hidden>
Date: 2013-01-30 13:26:37 

On Tue, Jan 29, 2013 at 02:54:35PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
On 13:28 Mon 10 Dec     , Johan Hovold wrote:
quoted
Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.

Use SOC-type to determine the pixel layout.

Tested on custom at91sam9263-board.

Cc: <redacted>
Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 22 +++++++++++++++-------
 include/video/atmel_lcdc.h  |  1 +
 2 files changed, 16 insertions(+), 7 deletions(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 1505539..1f68fa6 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -422,17 +422,22 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
 			= var->bits_per_pixel;
 		break;
 	case 16:
+		/* Older SOCs use IBGR:555 rather than BGR:565. */
+		if (sinfo->have_intensity_bit)
+			var->green.length = 5;
+		else
+			var->green.length = 6;
+
 		if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
-			/* RGB:565 mode */
-			var->red.offset = 11;
+			/* RGB:5X5 mode */
+			var->red.offset = var->green.length + 5;
 			var->blue.offset = 0;
 		} else {
-			/* BGR:565 mode */
+			/* BGR:5X5 mode */
 			var->red.offset = 0;
-			var->blue.offset = 11;
+			var->blue.offset = var->green.length + 5;
 		}
 		var->green.offset = 5;
-		var->green.length = 6;
 		var->red.length = var->blue.length = 5;
 		break;
 	case 32:
@@ -679,8 +684,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
 
 	case FB_VISUAL_PSEUDOCOLOR:
 		if (regno < 256) {
-			if (cpu_is_at91sam9261() || cpu_is_at91sam9263()
-			    || cpu_is_at91sam9rl()) {
+			if (sinfo->have_intensity_bit) {
 				/* old style I+BGR:555 */
 				val  = ((red   >> 11) & 0x001f);
 				val |= ((green >>  6) & 0x03e0);
@@ -870,6 +874,10 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	}
 	sinfo->info = info;
 	sinfo->pdev = pdev;
+	if (cpu_is_at91sam9261() || cpu_is_at91sam9263() ||
+							cpu_is_at91sam9rl()) {
+		sinfo->have_intensity_bit = true;
+	}
nack

you need to drop the cpu_is as this can only be use now for the core

use platform_device_id to indetify the IP as done on at91-i2c as we can not
detect the IP version
If this was a new feature and not a regression, fix I'd fully agree. There
are however currently four places in atmel_lcdfb where cpu_is macros are
used, and my patch only refactors one of them.

I can submit a follow up patch which add platform_device_id support, but
such a patch will be quite invasive and thus not 3.8-rc or stable material.

How about accepting this patch as it is, considering that it fixes an
obvious regression and also facilitate the move to platform_device_id by
introducing the intensity-bit flag?

Thanks,
Johan

[PATCH 0/5] atmel_lcdfb: regression fixes and cpu_is removal

From: Johan Hovold <hidden>
Date: 2013-02-05 13:35:10 

The first three patches are resends of two regression fixes and one clean up
posted in December (with previous acked-bys included). The regression fixes are
kept minimal and are tagged for stable.

The last two patches replace all uses of cpu_is macros in atmel_lcdfb with a
platform-device-id table and static configurations.

Thanks,
Johan


Johan Hovold (5):
  atmel_lcdfb: fix 16-bpp modes on older SOCs
  ARM: at91/neocore926: fix LCD-wiring mode
  atmel_lcdfb: remove unsupported 15-bpp mode
  atmel_lcdfb: move lcdcon2 register access to compute_hozval
  ARM: at91/avr32/atmel_lcdfb: replace cpu_is macros with device-id
    table

 arch/arm/mach-at91/at91sam9261_devices.c |   6 +-
 arch/arm/mach-at91/at91sam9263_devices.c |   2 +-
 arch/arm/mach-at91/at91sam9g45_devices.c |   6 +-
 arch/arm/mach-at91/at91sam9rl_devices.c  |   2 +-
 arch/arm/mach-at91/board-neocore926.c    |   2 +-
 arch/avr32/mach-at32ap/at32ap700x.c      |   2 +
 drivers/video/atmel_lcdfb.c              | 115 ++++++++++++++++++++++++++-----
 include/video/atmel_lcdc.h               |   4 +-
 8 files changed, 116 insertions(+), 23 deletions(-)

-- 
1.8.1.1

[PATCH 1/5] atmel_lcdfb: fix 16-bpp modes on older SOCs

From: Johan Hovold <hidden>
Date: 2013-02-05 13:35:11 

Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.

Use SOC-type to determine the pixel layout.

Tested on at91sam9263 and at91sam9g45.

Cc: <redacted>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 22 +++++++++++++++-------
 include/video/atmel_lcdc.h  |  1 +
 2 files changed, 16 insertions(+), 7 deletions(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 12cf5f3..025428e 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -422,17 +422,22 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
 			= var->bits_per_pixel;
 		break;
 	case 16:
+		/* Older SOCs use IBGR:555 rather than BGR:565. */
+		if (sinfo->have_intensity_bit)
+			var->green.length = 5;
+		else
+			var->green.length = 6;
+
 		if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
-			/* RGB:565 mode */
-			var->red.offset = 11;
+			/* RGB:5X5 mode */
+			var->red.offset = var->green.length + 5;
 			var->blue.offset = 0;
 		} else {
-			/* BGR:565 mode */
+			/* BGR:5X5 mode */
 			var->red.offset = 0;
-			var->blue.offset = 11;
+			var->blue.offset = var->green.length + 5;
 		}
 		var->green.offset = 5;
-		var->green.length = 6;
 		var->red.length = var->blue.length = 5;
 		break;
 	case 32:
@@ -679,8 +684,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
 
 	case FB_VISUAL_PSEUDOCOLOR:
 		if (regno < 256) {
-			if (cpu_is_at91sam9261() || cpu_is_at91sam9263()
-			    || cpu_is_at91sam9rl()) {
+			if (sinfo->have_intensity_bit) {
 				/* old style I+BGR:555 */
 				val  = ((red   >> 11) & 0x001f);
 				val |= ((green >>  6) & 0x03e0);
@@ -870,6 +874,10 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	}
 	sinfo->info = info;
 	sinfo->pdev = pdev;
+	if (cpu_is_at91sam9261() || cpu_is_at91sam9263() ||
+							cpu_is_at91sam9rl()) {
+		sinfo->have_intensity_bit = true;
+	}
 
 	strcpy(info->fix.id, sinfo->pdev->name);
 	info->flags = ATMEL_LCDFB_FBINFO_DEFAULT;
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 28447f1..5f0e234 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -62,6 +62,7 @@ struct atmel_lcdfb_info {
 	void (*atmel_lcdfb_power_control)(int on);
 	struct fb_monspecs	*default_monspecs;
 	u32			pseudo_palette[16];
+	bool			have_intensity_bit;
 };
 
 #define ATMEL_LCDC_DMABADDR1	0x00
-- 
1.8.1.1

[PATCH 2/5] ARM: at91/neocore926: fix LCD-wiring mode

From: Johan Hovold <hidden>
Date: 2013-02-05 13:35:12 

Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather than
BGR:565.

The above commit also removed the RGB:555-wiring hack without fixing the
neocore926 board which used it. Fix by specifying RGB-wiring and let the
driver handle the final SOC-dependant layout.

Remove the no longer used ATMEL_LCDC_WIRING_RGB555 define.

Compile-only tested.

Cc: <redacted>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <redacted>
---
 arch/arm/mach-at91/board-neocore926.c | 2 +-
 include/video/atmel_lcdc.h            | 1 -
 2 files changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
index bc7a1c4..4726297 100644
--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -266,7 +266,7 @@ static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = {
 	.default_monspecs		= &at91fb_default_monspecs,
 	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
 	.guard_time			= 1,
-	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB555,
+	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB,
 };
 
 #else
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 5f0e234..8deb226 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -30,7 +30,6 @@
  */
 #define ATMEL_LCDC_WIRING_BGR	0
 #define ATMEL_LCDC_WIRING_RGB	1
-#define ATMEL_LCDC_WIRING_RGB555	2
 
 
  /* LCD Controller info data structure, stored in device platform_data */
-- 
1.8.1.1

[PATCH 3/5] atmel_lcdfb: remove unsupported 15-bpp mode

From: Johan Hovold <hidden>
Date: 2013-02-05 13:35:13 

Since commit 787f9fd23283 ("atmel_lcdfb: support 16bit BGR:565 mode,
remove unsupported 15bit modes") atmel_lcdfb_check_var does not accept
15-bpp mode so remove it from atmel_lcdfb_set_par as well.

Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 025428e..93910e3 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -567,7 +567,6 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
 		case 2: value |= ATMEL_LCDC_PIXELSIZE_2; break;
 		case 4: value |= ATMEL_LCDC_PIXELSIZE_4; break;
 		case 8: value |= ATMEL_LCDC_PIXELSIZE_8; break;
-		case 15: /* fall through */
 		case 16: value |= ATMEL_LCDC_PIXELSIZE_16; break;
 		case 24: value |= ATMEL_LCDC_PIXELSIZE_24; break;
 		case 32: value |= ATMEL_LCDC_PIXELSIZE_32; break;
-- 
1.8.1.1

[PATCH 4/5] atmel_lcdfb: move lcdcon2 register access to compute_hozval

From: Johan Hovold <hidden>
Date: 2013-02-05 13:35:14 

Pass atmel_lcd_info structure to compute_hozval and only do the register
access on SOCs that actually use it.

This will also simplify the removal of the cpu_is macros.

Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 93910e3..347bab2 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -193,14 +193,17 @@ static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
 	.accel		= FB_ACCEL_NONE,
 };
 
-static unsigned long compute_hozval(unsigned long xres, unsigned long lcdcon2)
+static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
+							unsigned long xres)
 {
+	unsigned long lcdcon2;
 	unsigned long value;
 
 	if (!(cpu_is_at91sam9261() || cpu_is_at91sam9g10()
 		|| cpu_is_at32ap7000()))
 		return xres;
 
+	lcdcon2 = lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2);
 	value = xres;
 	if ((lcdcon2 & ATMEL_LCDC_DISTYPE) != ATMEL_LCDC_DISTYPE_TFT) {
 		/* STN display */
@@ -590,8 +593,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
 	lcdc_writel(sinfo, ATMEL_LCDC_TIM2, value);
 
 	/* Horizontal value (aka line size) */
-	hozval_linesz = compute_hozval(info->var.xres,
-					lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2));
+	hozval_linesz = compute_hozval(sinfo, info->var.xres);
 
 	/* Display size */
 	value = (hozval_linesz - 1) << ATMEL_LCDC_HOZVAL_OFFSET;
-- 
1.8.1.1

[PATCH 5/5] ARM: at91/avr32/atmel_lcdfb: replace cpu_is macros with device-id table

From: Johan Hovold <hidden>
Date: 2013-02-05 13:35:15 

Remove cpu_is macros from atmel lcdfb driver and use platform-device-id
table to determine platform configuration parameters.

The currently used configuration parameters are:

have_alt_pixclock
 - SOC uses an alternate pixel-clock calculation formula (at91sam9g45
   non-ES)

have_bus_clk
 - SOC has bus clock hck1 (at91sam9261, at921sam9g10 and at32ap)

have_hozval
 - SOC has a HOZVAL field in LCDFRMCFG which is used to determine the
   linesize for STN displays (at91sam9261, at921sam9g10 and at32ap)

have_intensity_bit
 - SOC uses IBGR:555 rather than BGR:565 16-bit pixel layout
   (at91sam9261, at91sam9263 and at91sam9rl)

Tested on at91sam9g45, compile-tested for other AT91 SOCs, and untested
for AVR32.

Signed-off-by: Johan Hovold <redacted>
---
 arch/arm/mach-at91/at91sam9261_devices.c |  6 +-
 arch/arm/mach-at91/at91sam9263_devices.c |  2 +-
 arch/arm/mach-at91/at91sam9g45_devices.c |  6 +-
 arch/arm/mach-at91/at91sam9rl_devices.c  |  2 +-
 arch/avr32/mach-at32ap/at32ap700x.c      |  2 +
 drivers/video/atmel_lcdfb.c              | 96 ++++++++++++++++++++++++++++----
 include/video/atmel_lcdc.h               |  4 +-
 7 files changed, 101 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 92e0f86..01647cb 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -488,7 +488,6 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
@@ -505,6 +504,11 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 		return;
 	}
 
+	if (cpu_is_at91sam9g10())
+		at91_lcdc_device.name = "fb-at91sam9g10";
+	else
+		at91_lcdc_device.name = "fb-at91sam9261";
+
 #if defined(CONFIG_FB_ATMEL_STN)
 	at91_set_A_periph(AT91_PIN_PB0, 0);     /* LCDVSYNC */
 	at91_set_A_periph(AT91_PIN_PB1, 0);     /* LCDHSYNC */
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index ed666f5..a34f39a 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -848,7 +848,7 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
+	.name		= "fb-at91sam9263",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 827c9f2..1d5cc51 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -981,7 +981,6 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
@@ -997,6 +996,11 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 	if (!data)
 		return;
 
+	if (cpu_is_at91sam9g45es())
+		at91_lcdc_device.name = "fb-at91sam9g45es";
+	else
+		at91_lcdc_device.name = "fb-at91sam9g45";
+
 	at91_set_A_periph(AT91_PIN_PE0, 0);	/* LCDDPWR */
 
 	at91_set_A_periph(AT91_PIN_PE2, 0);	/* LCDCC */
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index ddf223f..13cac0a 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -514,7 +514,7 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
+	.name		= "fb-at91sam9rl",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index b323d8d..5cdaa07 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1530,6 +1530,8 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
 	memcpy(info, data, sizeof(struct atmel_lcdfb_info));
 	info->default_monspecs = monspecs;
 
+	pdev->name = "fb-at32ap";
+
 	platform_device_register(pdev);
 	return pdev;
 
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 347bab2..5ad49ed 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -34,6 +34,81 @@
 #define ATMEL_LCDC_DMA_BURST_LEN	8	/* words */
 #define ATMEL_LCDC_FIFO_SIZE		512	/* words */
 
+struct atmel_lcdfb_config {
+	bool have_alt_pixclock;
+	bool have_bus_clk;
+	bool have_hozval;
+	bool have_intensity_bit;
+};
+
+static struct atmel_lcdfb_config at91sam9261_config = {
+	.have_bus_clk		= true,
+	.have_intensity_bit	= true,
+	.have_hozval		= true,
+};
+
+static struct atmel_lcdfb_config at91sam9263_config = {
+	.have_intensity_bit	= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g10_config = {
+	.have_bus_clk		= true,
+	.have_hozval		= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g45_config = {
+	.have_alt_pixclock	= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g45es_config = {
+};
+
+static struct atmel_lcdfb_config at91sam9rl_config = {
+	.have_intensity_bit	= true,
+};
+
+static struct atmel_lcdfb_config at32ap_config = {
+	.have_bus_clk		= true,
+	.have_hozval		= true,
+};
+
+static const struct platform_device_id atmel_lcdfb_devtypes[] = {
+	{
+		.name = "fb-at91sam9261",
+		.driver_data = (unsigned long)&at91sam9261_config,
+	}, {
+		.name = "fb-at91sam9263",
+		.driver_data = (unsigned long)&at91sam9263_config,
+	}, {
+		.name = "fb-at91sam9g10",
+		.driver_data = (unsigned long)&at91sam9g10_config,
+	}, {
+		.name = "fb-at91sam9g45",
+		.driver_data = (unsigned long)&at91sam9g45_config,
+	}, {
+		.name = "fb-at91sam9g45es",
+		.driver_data = (unsigned long)&at91sam9g45es_config,
+	}, {
+		.name = "fb-at91sam9rl",
+		.driver_data = (unsigned long)&at91sam9rl_config,
+	}, {
+		.name = "fb-at32ap",
+		.driver_data = (unsigned long)&at32ap_config,
+	}, {
+		/* terminator */
+	}
+};
+
+static struct atmel_lcdfb_config *
+atmel_lcdfb_get_config(struct platform_device *pdev)
+{
+	unsigned long data;
+
+	data = platform_get_device_id(pdev)->driver_data;
+
+	return (struct atmel_lcdfb_config *)data;
+}
+
 #if defined(CONFIG_ARCH_AT91)
 #define	ATMEL_LCDFB_FBINFO_DEFAULT	(FBINFO_DEFAULT \
 					 | FBINFO_PARTIAL_PAN_OK \
@@ -199,8 +274,7 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
 	unsigned long lcdcon2;
 	unsigned long value;
 
-	if (!(cpu_is_at91sam9261() || cpu_is_at91sam9g10()
-		|| cpu_is_at32ap7000()))
+	if (!sinfo->config->have_hozval)
 		return xres;
 
 	lcdcon2 = lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2);
@@ -426,7 +500,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
 		break;
 	case 16:
 		/* Older SOCs use IBGR:555 rather than BGR:565. */
-		if (sinfo->have_intensity_bit)
+		if (sinfo->config->have_intensity_bit)
 			var->green.length = 5;
 		else
 			var->green.length = 6;
@@ -534,7 +608,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
 	/* Now, the LCDC core... */
 
 	/* Set pixel clock */
-	if (cpu_is_at91sam9g45() && !cpu_is_at91sam9g45es())
+	if (sinfo->config->have_alt_pixclock)
 		pix_factor = 1;
 
 	clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
@@ -685,7 +759,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
 
 	case FB_VISUAL_PSEUDOCOLOR:
 		if (regno < 256) {
-			if (sinfo->have_intensity_bit) {
+			if (sinfo->config->have_intensity_bit) {
 				/* old style I+BGR:555 */
 				val  = ((red   >> 11) & 0x001f);
 				val |= ((green >>  6) & 0x03e0);
@@ -875,10 +949,9 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	}
 	sinfo->info = info;
 	sinfo->pdev = pdev;
-	if (cpu_is_at91sam9261() || cpu_is_at91sam9263() ||
-							cpu_is_at91sam9rl()) {
-		sinfo->have_intensity_bit = true;
-	}
+	sinfo->config = atmel_lcdfb_get_config(pdev);
+	if (!sinfo->config)
+		goto free_info;
 
 	strcpy(info->fix.id, sinfo->pdev->name);
 	info->flags = ATMEL_LCDFB_FBINFO_DEFAULT;
@@ -889,8 +962,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	info->fix = atmel_lcdfb_fix;
 
 	/* Enable LCDC Clocks */
-	if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()
-	 || cpu_is_at32ap7000()) {
+	if (sinfo->config->have_bus_clk) {
 		sinfo->bus_clk = clk_get(dev, "hck1");
 		if (IS_ERR(sinfo->bus_clk)) {
 			ret = PTR_ERR(sinfo->bus_clk);
@@ -1152,7 +1224,7 @@ static struct platform_driver atmel_lcdfb_driver = {
 	.remove		= __exit_p(atmel_lcdfb_remove),
 	.suspend	= atmel_lcdfb_suspend,
 	.resume		= atmel_lcdfb_resume,
-
+	.id_table	= atmel_lcdfb_devtypes,
 	.driver		= {
 		.name	= "atmel_lcdfb",
 		.owner	= THIS_MODULE,
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 8deb226..0f5a2fc 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -31,6 +31,7 @@
 #define ATMEL_LCDC_WIRING_BGR	0
 #define ATMEL_LCDC_WIRING_RGB	1
 
+struct atmel_lcdfb_config;
 
  /* LCD Controller info data structure, stored in device platform_data */
 struct atmel_lcdfb_info {
@@ -61,7 +62,8 @@ struct atmel_lcdfb_info {
 	void (*atmel_lcdfb_power_control)(int on);
 	struct fb_monspecs	*default_monspecs;
 	u32			pseudo_palette[16];
-	bool			have_intensity_bit;
+
+	struct atmel_lcdfb_config *config;
 };
 
 #define ATMEL_LCDC_DMABADDR1	0x00
-- 
1.8.1.1

[PATCH 5/5] ARM: at91/avr32/atmel_lcdfb: replace cpu_is macros with device-id table

From: Jean-Christophe PLAGNIOL-VILLARD <hidden>
Date: 2013-02-05 20:11:45 

On 14:35 Tue 05 Feb     , Johan Hovold wrote:
Remove cpu_is macros from atmel lcdfb driver and use platform-device-id
table to determine platform configuration parameters.

The currently used configuration parameters are:

have_alt_pixclock
 - SOC uses an alternate pixel-clock calculation formula (at91sam9g45
   non-ES)

have_bus_clk
 - SOC has bus clock hck1 (at91sam9261, at921sam9g10 and at32ap)
no provide a clkdev a we do for macb
quoted hunk
have_hozval
 - SOC has a HOZVAL field in LCDFRMCFG which is used to determine the
   linesize for STN displays (at91sam9261, at921sam9g10 and at32ap)

have_intensity_bit
 - SOC uses IBGR:555 rather than BGR:565 16-bit pixel layout
   (at91sam9261, at91sam9263 and at91sam9rl)

Tested on at91sam9g45, compile-tested for other AT91 SOCs, and untested
for AVR32.

Signed-off-by: Johan Hovold <redacted>
---
 arch/arm/mach-at91/at91sam9261_devices.c |  6 +-
 arch/arm/mach-at91/at91sam9263_devices.c |  2 +-
 arch/arm/mach-at91/at91sam9g45_devices.c |  6 +-
 arch/arm/mach-at91/at91sam9rl_devices.c  |  2 +-
 arch/avr32/mach-at32ap/at32ap700x.c      |  2 +
 drivers/video/atmel_lcdfb.c              | 96 ++++++++++++++++++++++++++++----
 include/video/atmel_lcdc.h               |  4 +-
 7 files changed, 101 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 92e0f86..01647cb 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -488,7 +488,6 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
@@ -505,6 +504,11 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 		return;
 	}
 
+	if (cpu_is_at91sam9g10())
+		at91_lcdc_device.name = "fb-at91sam9g10";
use this

at91sam9g10-lcdfb

as we will use for dt
quoted hunk
+	else
+		at91_lcdc_device.name = "fb-at91sam9261";
+
 #if defined(CONFIG_FB_ATMEL_STN)
 	at91_set_A_periph(AT91_PIN_PB0, 0);     /* LCDVSYNC */
 	at91_set_A_periph(AT91_PIN_PB1, 0);     /* LCDHSYNC */
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index ed666f5..a34f39a 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -848,7 +848,7 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
+	.name		= "fb-at91sam9263",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 827c9f2..1d5cc51 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -981,7 +981,6 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
@@ -997,6 +996,11 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 	if (!data)
 		return;
 
+	if (cpu_is_at91sam9g45es())
+		at91_lcdc_device.name = "fb-at91sam9g45es";
+	else
+		at91_lcdc_device.name = "fb-at91sam9g45";
+
 	at91_set_A_periph(AT91_PIN_PE0, 0);	/* LCDDPWR */
 
 	at91_set_A_periph(AT91_PIN_PE2, 0);	/* LCDCC */
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index ddf223f..13cac0a 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -514,7 +514,7 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
+	.name		= "fb-at91sam9rl",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index b323d8d..5cdaa07 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1530,6 +1530,8 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
 	memcpy(info, data, sizeof(struct atmel_lcdfb_info));
 	info->default_monspecs = monspecs;
 
+	pdev->name = "fb-at32ap";
+
 	platform_device_register(pdev);
 	return pdev;
 
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 347bab2..5ad49ed 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -34,6 +34,81 @@
 #define ATMEL_LCDC_DMA_BURST_LEN	8	/* words */
 #define ATMEL_LCDC_FIFO_SIZE		512	/* words */
 
+struct atmel_lcdfb_config {
+	bool have_alt_pixclock;
+	bool have_bus_clk;
+	bool have_hozval;
+	bool have_intensity_bit;
+};
+
+static struct atmel_lcdfb_config at91sam9261_config = {
+	.have_bus_clk		= true,
+	.have_intensity_bit	= true,
+	.have_hozval		= true,
+};
+
+static struct atmel_lcdfb_config at91sam9263_config = {
+	.have_intensity_bit	= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g10_config = {
+	.have_bus_clk		= true,
+	.have_hozval		= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g45_config = {
+	.have_alt_pixclock	= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g45es_config = {
+};
+
+static struct atmel_lcdfb_config at91sam9rl_config = {
+	.have_intensity_bit	= true,
+};
+
+static struct atmel_lcdfb_config at32ap_config = {
+	.have_bus_clk		= true,
+	.have_hozval		= true,
+};
+
+static const struct platform_device_id atmel_lcdfb_devtypes[] = {
+	{
+		.name = "fb-at91sam9261",
+		.driver_data = (unsigned long)&at91sam9261_config,
+	}, {
+		.name = "fb-at91sam9263",
+		.driver_data = (unsigned long)&at91sam9263_config,
+	}, {
+		.name = "fb-at91sam9g10",
+		.driver_data = (unsigned long)&at91sam9g10_config,
+	}, {
+		.name = "fb-at91sam9g45",
+		.driver_data = (unsigned long)&at91sam9g45_config,
+	}, {
+		.name = "fb-at91sam9g45es",
+		.driver_data = (unsigned long)&at91sam9g45es_config,
+	}, {
+		.name = "fb-at91sam9rl",
+		.driver_data = (unsigned long)&at91sam9rl_config,
+	}, {
+		.name = "fb-at32ap",
+		.driver_data = (unsigned long)&at32ap_config,
+	}, {
+		/* terminator */
+	}
+};
+
+static struct atmel_lcdfb_config *
+atmel_lcdfb_get_config(struct platform_device *pdev)
+{
+	unsigned long data;
+
+	data = platform_get_device_id(pdev)->driver_data;
+
+	return (struct atmel_lcdfb_config *)data;
+}
+
 #if defined(CONFIG_ARCH_AT91)
 #define	ATMEL_LCDFB_FBINFO_DEFAULT	(FBINFO_DEFAULT \
 					 | FBINFO_PARTIAL_PAN_OK \
@@ -199,8 +274,7 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
 	unsigned long lcdcon2;
 	unsigned long value;
 
-	if (!(cpu_is_at91sam9261() || cpu_is_at91sam9g10()
-		|| cpu_is_at32ap7000()))
+	if (!sinfo->config->have_hozval)
 		return xres;
 
 	lcdcon2 = lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2);
@@ -426,7 +500,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
 		break;
 	case 16:
 		/* Older SOCs use IBGR:555 rather than BGR:565. */
-		if (sinfo->have_intensity_bit)
+		if (sinfo->config->have_intensity_bit)
 			var->green.length = 5;
 		else
 			var->green.length = 6;
@@ -534,7 +608,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
 	/* Now, the LCDC core... */
 
 	/* Set pixel clock */
-	if (cpu_is_at91sam9g45() && !cpu_is_at91sam9g45es())
+	if (sinfo->config->have_alt_pixclock)
 		pix_factor = 1;
 
 	clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
@@ -685,7 +759,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
 
 	case FB_VISUAL_PSEUDOCOLOR:
 		if (regno < 256) {
-			if (sinfo->have_intensity_bit) {
+			if (sinfo->config->have_intensity_bit) {
 				/* old style I+BGR:555 */
 				val  = ((red   >> 11) & 0x001f);
 				val |= ((green >>  6) & 0x03e0);
@@ -875,10 +949,9 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	}
 	sinfo->info = info;
 	sinfo->pdev = pdev;
-	if (cpu_is_at91sam9261() || cpu_is_at91sam9263() ||
-							cpu_is_at91sam9rl()) {
-		sinfo->have_intensity_bit = true;
-	}
+	sinfo->config = atmel_lcdfb_get_config(pdev);
+	if (!sinfo->config)
+		goto free_info;
 
 	strcpy(info->fix.id, sinfo->pdev->name);
 	info->flags = ATMEL_LCDFB_FBINFO_DEFAULT;
@@ -889,8 +962,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	info->fix = atmel_lcdfb_fix;
 
 	/* Enable LCDC Clocks */
-	if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()
-	 || cpu_is_at32ap7000()) {
+	if (sinfo->config->have_bus_clk) {
 		sinfo->bus_clk = clk_get(dev, "hck1");
 		if (IS_ERR(sinfo->bus_clk)) {
 			ret = PTR_ERR(sinfo->bus_clk);
@@ -1152,7 +1224,7 @@ static struct platform_driver atmel_lcdfb_driver = {
 	.remove		= __exit_p(atmel_lcdfb_remove),
 	.suspend	= atmel_lcdfb_suspend,
 	.resume		= atmel_lcdfb_resume,
-
+	.id_table	= atmel_lcdfb_devtypes,
 	.driver		= {
 		.name	= "atmel_lcdfb",
 		.owner	= THIS_MODULE,
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 8deb226..0f5a2fc 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -31,6 +31,7 @@
 #define ATMEL_LCDC_WIRING_BGR	0
 #define ATMEL_LCDC_WIRING_RGB	1
 
+struct atmel_lcdfb_config;
 
  /* LCD Controller info data structure, stored in device platform_data */
 struct atmel_lcdfb_info {
@@ -61,7 +62,8 @@ struct atmel_lcdfb_info {
 	void (*atmel_lcdfb_power_control)(int on);
 	struct fb_monspecs	*default_monspecs;
 	u32			pseudo_palette[16];
-	bool			have_intensity_bit;
+
+	struct atmel_lcdfb_config *config;
 };
 
 #define ATMEL_LCDC_DMABADDR1	0x00
-- 
1.8.1.1

[PATCH v2 0/3] ARM: at91/avr32/atmel_lcdfb: remove cpu_is macros

From: Johan Hovold <hidden>
Date: 2013-02-07 15:31:55 

Here's a v2 replacing the last two patches in the series (the first three are
unchanged since the first post). If preferred, I can repost the whole series
when these patches have been acked.

v2:
 - use clkdev to handle the lcdc bus clock
 - use -lcdfb suffix for device ids (e.g. "at91sam9g45-lcdfb")

Thanks,
Johan

Johan Hovold (3):
  ARM: at91/avr32/atmel_lcdfb: add bus-clock entry
  atmel_lcdfb: move lcdcon2 register access to compute_hozval
  ARM: at91/avr32/atmel_lcdfb: add platform device-id table

 arch/arm/mach-at91/at91sam9261.c         |   2 +
 arch/arm/mach-at91/at91sam9261_devices.c |   6 +-
 arch/arm/mach-at91/at91sam9263.c         |   1 +
 arch/arm/mach-at91/at91sam9263_devices.c |   2 +-
 arch/arm/mach-at91/at91sam9g45.c         |   2 +
 arch/arm/mach-at91/at91sam9g45_devices.c |   6 +-
 arch/arm/mach-at91/at91sam9rl.c          |   1 +
 arch/arm/mach-at91/at91sam9rl_devices.c  |   2 +-
 arch/avr32/mach-at32ap/at32ap700x.c      |   6 +-
 drivers/video/atmel_lcdfb.c              | 120 +++++++++++++++++++++++--------
 include/video/atmel_lcdc.h               |   4 +-
 11 files changed, 117 insertions(+), 35 deletions(-)

-- 
1.8.1.1

[PATCH v2 1/3] ARM: at91/avr32/atmel_lcdfb: add bus-clock entry

From: Johan Hovold <hidden>
Date: 2013-02-07 15:31:56 

Add hclk entry for the atmel_lcdfb bus clock.

On at91sam9261, at91sam9g10 and at32ap the bus clock has to be enabled
as well as the peripheral clock. Add the appropriate lookup entries to
these SOCs and fake clocks to the SOCs that do not use it.

This allows us to get rid of the conditional enabling of the clocks in
the driver which relied on the cpu_is macros.

Tested on at91sam9263 and at91sam9g45, compile-tested for other
AT91-SOCs, and untested for AVR32.

Signed-off-by: Johan Hovold <redacted>
---
 arch/arm/mach-at91/at91sam9261.c    |  1 +
 arch/arm/mach-at91/at91sam9263.c    |  1 +
 arch/arm/mach-at91/at91sam9g45.c    |  1 +
 arch/arm/mach-at91/at91sam9rl.c     |  1 +
 arch/avr32/mach-at32ap/at32ap700x.c |  4 ++--
 drivers/video/atmel_lcdfb.c         | 23 ++++++++---------------
 6 files changed, 14 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 2998a08..5838f12 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -169,6 +169,7 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &hck1),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index 4618776..53d6123 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -190,6 +190,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("pclk", "fff98000.ssc", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "fff9c000.ssc", &ssc1_clk),
+	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &lcdc_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index b6f1342..1def8c9 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -228,6 +228,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_ID("hclk", &macb_clk),
 	/* One additional fake clock for ohci */
 	CLKDEV_CON_ID("ohci_clk", &uhphs_clk),
+	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &lcdc_clk),
 	CLKDEV_CON_DEV_ID("ehci_clk", "atmel-ehci", &uhphs_clk),
 	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
 	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index eb98704..4cd4fa9 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -179,6 +179,7 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &lcdc_clk),
 	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
 	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index b323d8d..cd25b01 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1453,7 +1453,7 @@ static struct resource atmel_lcdfb0_resource[] = {
 	},
 };
 DEFINE_DEV_DATA(atmel_lcdfb, 0);
-DEV_CLK(hck1, atmel_lcdfb0, hsb, 7);
+DEV_CLK(hclk, atmel_lcdfb0, hsb, 7);
 static struct clk atmel_lcdfb0_pixclk = {
 	.name		= "lcdc_clk",
 	.dev		= &atmel_lcdfb0_device.dev,
@@ -2246,7 +2246,7 @@ static __initdata struct clk *init_clocks[] = {
 	&atmel_twi0_pclk,
 	&atmel_mci0_pclk,
 #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
-	&atmel_lcdfb0_hck1,
+	&atmel_lcdfb0_hclk,
 	&atmel_lcdfb0_pixclk,
 #endif
 	&ssc0_pclk,
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 93910e3..86cafae 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -820,15 +820,13 @@ static int __init atmel_lcdfb_init_fbinfo(struct atmel_lcdfb_info *sinfo)
 
 static void atmel_lcdfb_start_clock(struct atmel_lcdfb_info *sinfo)
 {
-	if (sinfo->bus_clk)
-		clk_enable(sinfo->bus_clk);
+	clk_enable(sinfo->bus_clk);
 	clk_enable(sinfo->lcdc_clk);
 }
 
 static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
 {
-	if (sinfo->bus_clk)
-		clk_disable(sinfo->bus_clk);
+	clk_disable(sinfo->bus_clk);
 	clk_disable(sinfo->lcdc_clk);
 }
 
@@ -887,13 +885,10 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	info->fix = atmel_lcdfb_fix;
 
 	/* Enable LCDC Clocks */
-	if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()
-	 || cpu_is_at32ap7000()) {
-		sinfo->bus_clk = clk_get(dev, "hck1");
-		if (IS_ERR(sinfo->bus_clk)) {
-			ret = PTR_ERR(sinfo->bus_clk);
-			goto free_info;
-		}
+	sinfo->bus_clk = clk_get(dev, "hclk");
+	if (IS_ERR(sinfo->bus_clk)) {
+		ret = PTR_ERR(sinfo->bus_clk);
+		goto free_info;
 	}
 	sinfo->lcdc_clk = clk_get(dev, "lcdc_clk");
 	if (IS_ERR(sinfo->lcdc_clk)) {
@@ -1054,8 +1049,7 @@ stop_clk:
 	atmel_lcdfb_stop_clock(sinfo);
 	clk_put(sinfo->lcdc_clk);
 put_bus_clk:
-	if (sinfo->bus_clk)
-		clk_put(sinfo->bus_clk);
+	clk_put(sinfo->bus_clk);
 free_info:
 	framebuffer_release(info);
 out:
@@ -1080,8 +1074,7 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
 	unregister_framebuffer(info);
 	atmel_lcdfb_stop_clock(sinfo);
 	clk_put(sinfo->lcdc_clk);
-	if (sinfo->bus_clk)
-		clk_put(sinfo->bus_clk);
+	clk_put(sinfo->bus_clk);
 	fb_dealloc_cmap(&info->cmap);
 	free_irq(sinfo->irq_base, info);
 	iounmap(sinfo->mmio);
-- 
1.8.1.1

[PATCH v2 2/3] atmel_lcdfb: move lcdcon2 register access to compute_hozval

From: Johan Hovold <hidden>
Date: 2013-02-07 15:31:57 

Pass atmel_lcd_info structure to compute_hozval and only do the register
access on SOCs that actually use it.

This will also simplify the removal of the cpu_is macros.

Signed-off-by: Johan Hovold <redacted>
---
 drivers/video/atmel_lcdfb.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 86cafae..c707130 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -193,14 +193,17 @@ static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
 	.accel		= FB_ACCEL_NONE,
 };
 
-static unsigned long compute_hozval(unsigned long xres, unsigned long lcdcon2)
+static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
+							unsigned long xres)
 {
+	unsigned long lcdcon2;
 	unsigned long value;
 
 	if (!(cpu_is_at91sam9261() || cpu_is_at91sam9g10()
 		|| cpu_is_at32ap7000()))
 		return xres;
 
+	lcdcon2 = lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2);
 	value = xres;
 	if ((lcdcon2 & ATMEL_LCDC_DISTYPE) != ATMEL_LCDC_DISTYPE_TFT) {
 		/* STN display */
@@ -590,8 +593,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
 	lcdc_writel(sinfo, ATMEL_LCDC_TIM2, value);
 
 	/* Horizontal value (aka line size) */
-	hozval_linesz = compute_hozval(info->var.xres,
-					lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2));
+	hozval_linesz = compute_hozval(sinfo, info->var.xres);
 
 	/* Display size */
 	value = (hozval_linesz - 1) << ATMEL_LCDC_HOZVAL_OFFSET;
-- 
1.8.1.1

[PATCH v2 3/3] ARM: at91/avr32/atmel_lcdfb: add platform device-id table

From: Johan Hovold <hidden>
Date: 2013-02-07 15:31:58 

Add platform device-id table in order to identify the controller and
determine its configuration.

The currently used configuration parameters are:

have_alt_pixclock
 - SOC uses an alternate pixel-clock calculation formula (at91sam9g45
   non-ES)

have_hozval
 - SOC has a HOZVAL field in LCDFRMCFG which is used to determine the
   linesize for STN displays (at91sam9261, at921sam9g10 and at32ap)

have_intensity_bit
 - SOC uses IBGR:555 rather than BGR:565 16-bit pixel layout
   (at91sam9261, at91sam9263 and at91sam9rl)

This allows us to remove all the remaining uses of cpu_is macros from
the driver.

Tested on at91sam9263 and at91sam9g45, compile-tested for other
AT91-SOCs, and untested for AVR32.

Signed-off-by: Johan Hovold <redacted>
---
 arch/arm/mach-at91/at91sam9261.c         |  3 +-
 arch/arm/mach-at91/at91sam9261_devices.c |  6 ++-
 arch/arm/mach-at91/at91sam9263.c         |  2 +-
 arch/arm/mach-at91/at91sam9263_devices.c |  2 +-
 arch/arm/mach-at91/at91sam9g45.c         |  3 +-
 arch/arm/mach-at91/at91sam9g45_devices.c |  6 ++-
 arch/arm/mach-at91/at91sam9rl.c          |  2 +-
 arch/arm/mach-at91/at91sam9rl_devices.c  |  2 +-
 arch/avr32/mach-at32ap/at32ap700x.c      |  2 +
 drivers/video/atmel_lcdfb.c              | 89 ++++++++++++++++++++++++++++----
 include/video/atmel_lcdc.h               |  4 +-
 11 files changed, 102 insertions(+), 19 deletions(-)

diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 5838f12..0204f4c 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -169,7 +169,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &hck1),
+	CLKDEV_CON_DEV_ID("hclk", "at91sam9261-lcdfb.0", &hck1),
+	CLKDEV_CON_DEV_ID("hclk", "at91sam9g10-lcdfb.0", &hck1),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 92e0f86..629ea5f 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -488,7 +488,6 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
@@ -505,6 +504,11 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 		return;
 	}
 
+	if (cpu_is_at91sam9g10())
+		at91_lcdc_device.name = "at91sam9g10-lcdfb";
+	else
+		at91_lcdc_device.name = "at91sam9261-lcdfb";
+
 #if defined(CONFIG_FB_ATMEL_STN)
 	at91_set_A_periph(AT91_PIN_PB0, 0);     /* LCDVSYNC */
 	at91_set_A_periph(AT91_PIN_PB1, 0);     /* LCDHSYNC */
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index 53d6123..c0cbb81 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -190,7 +190,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("pclk", "fff98000.ssc", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "fff9c000.ssc", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &lcdc_clk),
+	CLKDEV_CON_DEV_ID("hclk", "at91sam9263-lcdfb.0", &lcdc_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index ed666f5..858c8aa 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -848,7 +848,7 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
+	.name		= "at91sam9263-lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index 1def8c9..b4968aa 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -228,7 +228,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_ID("hclk", &macb_clk),
 	/* One additional fake clock for ohci */
 	CLKDEV_CON_ID("ohci_clk", &uhphs_clk),
-	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &lcdc_clk),
+	CLKDEV_CON_DEV_ID("hclk", "at91sam9g45-lcdfb.0", &lcdc_clk),
+	CLKDEV_CON_DEV_ID("hclk", "at91sam9g45es-lcdfb.0", &lcdc_clk),
 	CLKDEV_CON_DEV_ID("ehci_clk", "atmel-ehci", &uhphs_clk),
 	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
 	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 827c9f2..fe626d4 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -981,7 +981,6 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
@@ -997,6 +996,11 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 	if (!data)
 		return;
 
+	if (cpu_is_at91sam9g45es())
+		at91_lcdc_device.name = "at91sam9g45es-lcdfb";
+	else
+		at91_lcdc_device.name = "at91sam9g45-lcdfb";
+
 	at91_set_A_periph(AT91_PIN_PE0, 0);	/* LCDDPWR */
 
 	at91_set_A_periph(AT91_PIN_PE2, 0);	/* LCDCC */
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index 4cd4fa9..3de3e04 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -179,7 +179,7 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("hclk", "atmel_lcdfb.0", &lcdc_clk),
+	CLKDEV_CON_DEV_ID("hclk", "at91sam9rl-lcdfb.0", &lcdc_clk),
 	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
 	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index ddf223f..352468f 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -514,7 +514,7 @@ static struct resource lcdc_resources[] = {
 };
 
 static struct platform_device at91_lcdc_device = {
-	.name		= "atmel_lcdfb",
+	.name		= "at91sam9rl-lcdfb",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &lcdc_dmamask,
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index cd25b01..7c2f668 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1530,6 +1530,8 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
 	memcpy(info, data, sizeof(struct atmel_lcdfb_info));
 	info->default_monspecs = monspecs;
 
+	pdev->name = "at32ap-lcdfb";
+
 	platform_device_register(pdev);
 	return pdev;
 
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index c707130..b68bfe6 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -34,6 +34,77 @@
 #define ATMEL_LCDC_DMA_BURST_LEN	8	/* words */
 #define ATMEL_LCDC_FIFO_SIZE		512	/* words */
 
+struct atmel_lcdfb_config {
+	bool have_alt_pixclock;
+	bool have_hozval;
+	bool have_intensity_bit;
+};
+
+static struct atmel_lcdfb_config at91sam9261_config = {
+	.have_hozval		= true,
+	.have_intensity_bit	= true,
+};
+
+static struct atmel_lcdfb_config at91sam9263_config = {
+	.have_intensity_bit	= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g10_config = {
+	.have_hozval		= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g45_config = {
+	.have_alt_pixclock	= true,
+};
+
+static struct atmel_lcdfb_config at91sam9g45es_config = {
+};
+
+static struct atmel_lcdfb_config at91sam9rl_config = {
+	.have_intensity_bit	= true,
+};
+
+static struct atmel_lcdfb_config at32ap_config = {
+	.have_hozval		= true,
+};
+
+static const struct platform_device_id atmel_lcdfb_devtypes[] = {
+	{
+		.name = "at91sam9261-lcdfb",
+		.driver_data = (unsigned long)&at91sam9261_config,
+	}, {
+		.name = "at91sam9263-lcdfb",
+		.driver_data = (unsigned long)&at91sam9263_config,
+	}, {
+		.name = "at91sam9g10-lcdfb",
+		.driver_data = (unsigned long)&at91sam9g10_config,
+	}, {
+		.name = "at91sam9g45-lcdfb",
+		.driver_data = (unsigned long)&at91sam9g45_config,
+	}, {
+		.name = "at91sam9g45es-lcdfb",
+		.driver_data = (unsigned long)&at91sam9g45es_config,
+	}, {
+		.name = "at91sam9rl-lcdfb",
+		.driver_data = (unsigned long)&at91sam9rl_config,
+	}, {
+		.name = "at32ap-lcdfb",
+		.driver_data = (unsigned long)&at32ap_config,
+	}, {
+		/* terminator */
+	}
+};
+
+static struct atmel_lcdfb_config *
+atmel_lcdfb_get_config(struct platform_device *pdev)
+{
+	unsigned long data;
+
+	data = platform_get_device_id(pdev)->driver_data;
+
+	return (struct atmel_lcdfb_config *)data;
+}
+
 #if defined(CONFIG_ARCH_AT91)
 #define	ATMEL_LCDFB_FBINFO_DEFAULT	(FBINFO_DEFAULT \
 					 | FBINFO_PARTIAL_PAN_OK \
@@ -199,8 +270,7 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
 	unsigned long lcdcon2;
 	unsigned long value;
 
-	if (!(cpu_is_at91sam9261() || cpu_is_at91sam9g10()
-		|| cpu_is_at32ap7000()))
+	if (!sinfo->config->have_hozval)
 		return xres;
 
 	lcdcon2 = lcdc_readl(sinfo, ATMEL_LCDC_LCDCON2);
@@ -426,7 +496,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
 		break;
 	case 16:
 		/* Older SOCs use IBGR:555 rather than BGR:565. */
-		if (sinfo->have_intensity_bit)
+		if (sinfo->config->have_intensity_bit)
 			var->green.length = 5;
 		else
 			var->green.length = 6;
@@ -534,7 +604,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
 	/* Now, the LCDC core... */
 
 	/* Set pixel clock */
-	if (cpu_is_at91sam9g45() && !cpu_is_at91sam9g45es())
+	if (sinfo->config->have_alt_pixclock)
 		pix_factor = 1;
 
 	clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
@@ -685,7 +755,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
 
 	case FB_VISUAL_PSEUDOCOLOR:
 		if (regno < 256) {
-			if (sinfo->have_intensity_bit) {
+			if (sinfo->config->have_intensity_bit) {
 				/* old style I+BGR:555 */
 				val  = ((red   >> 11) & 0x001f);
 				val |= ((green >>  6) & 0x03e0);
@@ -873,10 +943,9 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
 	}
 	sinfo->info = info;
 	sinfo->pdev = pdev;
-	if (cpu_is_at91sam9261() || cpu_is_at91sam9263() ||
-							cpu_is_at91sam9rl()) {
-		sinfo->have_intensity_bit = true;
-	}
+	sinfo->config = atmel_lcdfb_get_config(pdev);
+	if (!sinfo->config)
+		goto free_info;
 
 	strcpy(info->fix.id, sinfo->pdev->name);
 	info->flags = ATMEL_LCDFB_FBINFO_DEFAULT;
@@ -1145,7 +1214,7 @@ static struct platform_driver atmel_lcdfb_driver = {
 	.remove		= __exit_p(atmel_lcdfb_remove),
 	.suspend	= atmel_lcdfb_suspend,
 	.resume		= atmel_lcdfb_resume,
-
+	.id_table	= atmel_lcdfb_devtypes,
 	.driver		= {
 		.name	= "atmel_lcdfb",
 		.owner	= THIS_MODULE,
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 8deb226..0f5a2fc 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -31,6 +31,7 @@
 #define ATMEL_LCDC_WIRING_BGR	0
 #define ATMEL_LCDC_WIRING_RGB	1
 
+struct atmel_lcdfb_config;
 
  /* LCD Controller info data structure, stored in device platform_data */
 struct atmel_lcdfb_info {
@@ -61,7 +62,8 @@ struct atmel_lcdfb_info {
 	void (*atmel_lcdfb_power_control)(int on);
 	struct fb_monspecs	*default_monspecs;
 	u32			pseudo_palette[16];
-	bool			have_intensity_bit;
+
+	struct atmel_lcdfb_config *config;
 };
 
 #define ATMEL_LCDC_DMABADDR1	0x00
-- 
1.8.1.1
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help