diff --git a/Documentation/devicetree/bindings/net/ti-bluetooth.txt b/Documentation/devicetree/bindings/net/ti-bluetooth.txt
index f48c17b38f5851de..3c01cfc1e12dc132 100644
--- a/Documentation/devicetree/bindings/net/ti-bluetooth.txt
+++ b/Documentation/devicetree/bindings/net/ti-bluetooth.txt
@@ -13,7 +13,7 @@ and GPS over what's called "shared transport". The shared transport is
standard BT HCI protocol with additional channels for the other functions.
TI WiLink devices also have a separate WiFi interface as described in
-wireless/ti,wlcore.txt.
+wireless/ti,wlcore.yaml.
This bindings follows the UART slave device binding in ../serial/serial.yaml.
diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
deleted file mode 100644
index cb5c9e1569ca5300..0000000000000000
--- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
+++ /dev/null
@@ -1,57 +0,0 @@
-* Texas Instruments wl12xx/wl18xx wireless lan controller
-
-The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This
-document describes the binding for the SPI connected chip.
-
-Required properties:
-- compatible : Should be one of the following:
- * "ti,wl1271"
- * "ti,wl1273"
- * "ti,wl1281"
- * "ti,wl1283"
- * "ti,wl1801"
- * "ti,wl1805"
- * "ti,wl1807"
- * "ti,wl1831"
- * "ti,wl1835"
- * "ti,wl1837"
-- reg : Chip select address of device
-- spi-max-frequency : Maximum SPI clocking speed of device in Hz
-- interrupts : Should contain parameters for 1 interrupt line.
-- vwlan-supply : Point the node of the regulator that powers/enable the
- wl12xx/wl18xx chip
-
-Optional properties:
-- ref-clock-frequency : Reference clock frequency (should be set for wl12xx)
-- clock-xtal : boolean, clock is generated from XTAL
-
-- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
- for optional SPI connection related properties,
-
-Examples:
-
-For wl12xx family:
-&spi1 {
- wlcore: wlcore@1 {
- compatible = "ti,wl1271";
- reg = <1>;
- spi-max-frequency = <48000000>;
- interrupt-parent = <&gpio3>;
- interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
- vwlan-supply = <&vwlan_fixed>;
- clock-xtal;
- ref-clock-frequency = <38400000>;
- };
-};
-
-For wl18xx family:
-&spi0 {
- wlcore: wlcore@0 {
- compatible = "ti,wl1835";
- reg = <0>;
- spi-max-frequency = <48000000>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 IRQ_TYPE_EDGE_RISING>;
- vwlan-supply = <&vwlan_fixed>;
- };
-};diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
deleted file mode 100644
index 9306c4dadd46aea7..0000000000000000
--- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
+++ /dev/null
@@ -1,45 +0,0 @@
-TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices
-
-This node provides properties for controlling the wilink wireless device. The
-node is expected to be specified as a child node to the SDIO controller that
-connects the device to the system.
-
-Required properties:
- - compatible: should be one of the following:
- * "ti,wl1271"
- * "ti,wl1273"
- * "ti,wl1281"
- * "ti,wl1283"
- * "ti,wl1285"
- * "ti,wl1801"
- * "ti,wl1805"
- * "ti,wl1807"
- * "ti,wl1831"
- * "ti,wl1835"
- * "ti,wl1837"
- - interrupts : specifies attributes for the out-of-band interrupt.
-
-Optional properties:
- - ref-clock-frequency : ref clock frequency in Hz
- - tcxo-clock-frequency : tcxo clock frequency in Hz
-
-Note: the *-clock-frequency properties assume internal clocks. In case of external
-clock, new bindings (for parsing the clock nodes) have to be added.
-
-Example:
-
-&mmc3 {
- vmmc-supply = <&wlan_en_reg>;
- bus-width = <4>;
- cap-power-off-card;
- keep-power-in-suspend;
-
- #address-cells = <1>;
- #size-cells = <0>;
- wlcore: wlcore@2 {
- compatible = "ti,wl1835";
- reg = <2>;
- interrupt-parent = <&gpio0>;
- interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
- };
-};diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml
new file mode 100644
index 0000000000000000..8dd164d10290082a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml
@@ -0,0 +1,134 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/ti,wlcore.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments Wilink 6/7/8 (wl12xx/wl18xx) Wireless LAN Controller
+
+maintainers:
+ - Tony Lindgren <tony@atomide.com>
+
+description:
+ The wl12xx/wl18xx chips can be connected via SPI or via SDIO.
+ Note that the *-clock-frequency properties assume internal clocks. In case
+ of external clocks, new bindings (for parsing the clock nodes) have to be
+ added.
+
+properties:
+ compatible:
+ enum:
+ - ti,wl1271
+ - ti,wl1273
+ - ti,wl1281
+ - ti,wl1283
+ - ti,wl1285
+ - ti,wl1801
+ - ti,wl1805
+ - ti,wl1807
+ - ti,wl1831
+ - ti,wl1835
+ - ti,wl1837
+
+ reg:
+ maxItems: 1
+ description:
+ This is required when connected via SPI, and optional when connected via
+ SDIO.
+
+ spi-max-frequency: true
+
+ interrupts:
+ minItems: 1
+ maxItems: 2
+
+ interrupt-names:
+ items:
+ - const: irq
+ - const: wakeup
+
+ vwlan-supply:
+ description:
+ Points to the node of the regulator that powers/enable the wl12xx/wl18xx
+ chip. This is required when connected via SPI.
+
+
+ ref-clock-frequency:
+ description: Reference clock frequency.
+
+ tcxo-clock-frequency:
+ description: TCXO clock frequency.
+
+ clock-xtal:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Indicates that the clock is generated from XTAL.
+
+required:
+ - compatible
+ - interrupts
+
+if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - ti,wl1271
+ - ti,wl1273
+ - ti,wl1281
+ - ti,wl1283
+then:
+ required:
+ - ref-clock-frequency
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ // For wl12xx family:
+ spi1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wlcore1: wlcore@1 {
+ compatible = "ti,wl1271";
+ reg = <1>;
+ spi-max-frequency = <48000000>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ vwlan-supply = <&vwlan_fixed>;
+ clock-xtal;
+ ref-clock-frequency = <38400000>;
+ };
+ };
+
+ // For wl18xx family:
+ spi2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wlcore2: wlcore@0 {
+ compatible = "ti,wl1835";
+ reg = <0>;
+ spi-max-frequency = <48000000>;
+ interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+ vwlan-supply = <&vwlan_fixed>;
+ };
+ };
+
+ // SDIO example:
+ mmc3 {
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wlcore3: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };diff --git a/arch/arm/boot/dts/omap3-gta04a5.dts b/arch/arm/boot/dts/omap3-gta04a5.dts
index a2ba4030cf279683..0b5bd73888771438 100644
--- a/arch/arm/boot/dts/omap3-gta04a5.dts
+++ b/arch/arm/boot/dts/omap3-gta04a5.dts
@@ -79,7 +79,7 @@ OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT | MUX_MODE4) /* gpin114 */
/*
* for WL183x module see
- * Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
+ * Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml
*/
&wifi_pwrseq {--
2.25.1