[PATCH v2] dt-bindings: display/bridge: tc358767: Convert to YAML binding

@@ -1,54 +0,0 @@
-Toshiba TC358767 eDP bridge bindings
-
-Required properties:
- - compatible: "toshiba,tc358767"
- - reg: i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins
- - clock-names: should be "ref"
- - clocks: OF device-tree clock specification for refclk input. The reference
-   clock rate must be 13 MHz, 19.2 MHz, 26 MHz, or 38.4 MHz.
-
-Optional properties:
- - shutdown-gpios: OF device-tree gpio specification for SD pin
-                   (active high shutdown input)
- - reset-gpios: OF device-tree gpio specification for RSTX pin
-                (active low system reset)
- - toshiba,hpd-pin: TC358767 GPIO pin number to which HPD is connected to (0 or 1)
- - ports: the ports node can contain video interface port nodes to connect
-   to a DPI/DSI source and to an eDP/DP sink according to [1][2]:
-    - port@0: DSI input port
-    - port@1: DPI input port
-    - port@2: eDP/DP output port
-
-[1]: Documentation/devicetree/bindings/graph.txt
-[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-	edp-bridge@68 {
-		compatible = "toshiba,tc358767";
-		reg = <0x68>;
-		shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-		clock-names = "ref";
-		clocks = <&edp_refclk>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@1 {
-				reg = <1>;
-
-				bridge_in: endpoint {
-					remote-endpoint = <&dpi_out>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-
-				bridge_out: endpoint {
-					remote-endpoint = <&panel_in>;
-				};
-			};
-		};
-	};

@@ -0,0 +1,118 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/toshiba,tc358767.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba TC358767 MIPI-DSI or MIPI-DPI to DP/eDP bridge
+
+maintainers:
+  - Tomi Valkeinen <tomi.valkeinen@ti.com>
+
+properties:
+  compatible:
+    enum:
+      - toshiba,tc358767
+
+  reg:
+    description: I2C address of the bridge
+    enum: [0x68, 0x0f]
+
+  clocks:
+    description:
+      Reference clock input. The reference clock rate must be 13MHz, 19.2MHz,
+      26MHz, or 38.4MHz.
+    maxItems: 1
+
+  clock-names:
+    const: ref
+
+  reset-gpios:
+    description: GPIO connected to the RSTX signal.
+    maxItems: 1
+
+  shutdown-gpios:
+    description: GPIO connected to the SD signal.
+    maxItems: 1
+
+  toshiba,hpd-pin:
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    description: TC356767 GPIO pin number to which HPD is connected
+    enum:
+      - 0
+      - 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DSI input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DPI input
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for DP/eDP output (panel or connector).
+
+    oneOf:
+      - required:
+          - port@0
+      - required:
+          - port@1
+    required:
+      - port@2
+
+required:
+  - compatible
+  - reg
+  - clock-names
+  - clocks
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@68 {
+        compatible = "toshiba,tc358767";
+        reg = <0x68>;
+        clock-names = "ref";
+        clocks = <&edp_refclk>;
+        reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+        shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@1 {
+            reg = <1>;
+            bridge_in: endpoint {
+              remote-endpoint = <&dpi_out>;
+            };
+          };
+
+          port@2 {
+            reg = <2>;
+            bridge_out: endpoint {
+              remote-endpoint = <&panel_in>;
+            };
+          };
+        };
+      };
+    };
+
+...