[PATCH 1/2] dt-bindings: rtc: add generic bindings

Subsystems: open firmware and flattened device tree bindings, real time clock (rtc) subsystem, the rest

STALE2795d

7 messages, 3 authors, 2018-12-07 · open the first message on its own page

[PATCH 1/2] dt-bindings: rtc: add generic bindings

From: Alexandre Belloni <alexandre.belloni@bootlin.com>
Date: 2018-11-11 19:31:19

Add generic binding documentation for the RTC subsystem.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 Documentation/devicetree/bindings/rtc/rtc.txt | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc.txt
diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt
new file mode 100644
index 000000000000..221b7da50aca
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -0,0 +1,30 @@
+Generic device tree bindings for Real Time Clock devices
+========================================================
+
+This document describes generic bindings which can be used to describe Real Time
+Clock devices in a device tree.
+
+Required properties
+-------------------
+
+- compatible : name of RTC device following generic names recommended practice.
+
+For other required properties e.g. to describe register sets,
+clocks, etc. check the binding documentation of the specific driver.
+
+Optional properties
+-------------------
+
+- start-year : if provided, the default hardware range supported by the RTC is
+               shifted so the first usable year is the specified one.
+
+The following properties may not be supported by all drivers. However, if a
+driver wants to support one of the below features, it should adapt the bindings
+below.
+- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
+                          if trickle charger should be enabled
+- trickle-diode-disable : Do not use internal trickle charger diode Should be
+                          given if internal trickle charger diode should be
+                          disabled
+- wakeup-source :         Enables wake up of host system on alarm
+
-- 
2.19.1

[PATCH 2/2] dt-bindings: rtc: Move trivial RTCs to rtc.txt

From: Alexandre Belloni <alexandre.belloni@bootlin.com>
Date: 2018-11-11 19:31:21

Move trivial RTCs to the rtc generic binding documentation as they all also
support at least 'start-year'.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 Documentation/devicetree/bindings/rtc/rtc.txt | 34 +++++++++++++++++++
 .../devicetree/bindings/trivial-devices.txt   | 24 -------------
 2 files changed, 34 insertions(+), 24 deletions(-)
diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt
index 221b7da50aca..7c8da6926095 100644
--- a/Documentation/devicetree/bindings/rtc/rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -28,3 +28,37 @@ below.
                           disabled
 - wakeup-source :         Enables wake up of host system on alarm
 
+Trivial RTCs
+------------
+
+This is a list of trivial RTC devices that have simple device tree
+bindings, consisting only of a compatible field, an address and
+possibly an interrupt line.
+
+
+Compatible		Vendor / Chip
+==========		=============
+abracon,abb5zes3	AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
+dallas,ds1374		I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
+dallas,ds1672		Dallas DS1672 Real-time Clock
+dallas,ds3232		Extremely Accurate I²C RTC with Integrated Crystal and SRAM
+epson,rx8010		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+epson,rx8581		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+emmicro,em3027		EM Microelectronic EM3027 Real-time Clock
+isil,isl1208		Intersil ISL1208 Low Power RTC with Battery Backed SRAM
+isil,isl1218		Intersil ISL1218 Low Power RTC with Battery Backed SRAM
+isil,isl12022		Intersil ISL12022 Real-time Clock
+microcrystal,rv3029	Real Time Clock Module with I2C-Bus
+nxp,pcf2127		Real-time clock
+nxp,pcf2129		Real-time clock
+nxp,pcf8523		Real-time Clock
+nxp,pcf8563		Real-time clock/calendar
+nxp,pcf85063		Tiny Real-Time Clock
+pericom,pt7c4338	Real-time Clock Module
+ricoh,r2025sd		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,r2221tl		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,rs5c372a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,rs5c372b		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,rv5c386		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,rv5c387a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+sii,s35390a		2-wire CMOS real-time clock
diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt
index 6ab001fa1ed4..fda7a0f50c1e 100644
--- a/Documentation/devicetree/bindings/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/trivial-devices.txt
@@ -9,7 +9,6 @@ document for it just like any other devices.
 
 Compatible		Vendor / Chip
 ==========		=============
-abracon,abb5zes3		AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
 ad,ad7414		SMBus/I2C Digital Temperature Sensor in 6-Pin SOT with SMBus Alert and Over Temperature Pin
 ad,adm9240		ADM9240:  Complete System Hardware Monitor for uProcessor-Based Systems
 adi,adt7461		+/-1C TDM Extended Temp Range I.C
@@ -25,12 +24,9 @@ at,24c08		i2c serial eeprom  (24cxx)
 atmel,at97sc3204t	i2c trusted platform module (TPM)
 capella,cm32181		CM32181: Ambient Light Sensor
 capella,cm3232		CM3232: Ambient Light Sensor
-dallas,ds1374		I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
 dallas,ds1631		High-Precision Digital Thermometer
-dallas,ds1672		Dallas DS1672 Real-time Clock
 dallas,ds1682		Total-Elapsed-Time Recorder with Alarm
 dallas,ds1775		Tiny Digital Thermometer and Thermostat
-dallas,ds3232		Extremely Accurate I²C RTC with Integrated Crystal and SRAM
 dallas,ds4510		CPU Supervisor with Nonvolatile Memory and Programmable I/O
 dallas,ds75		Digital Thermometer and Thermostat
 devantech,srf02		Devantech SRF02 ultrasonic ranger in I2C mode
@@ -40,9 +36,6 @@ dlg,da9053		DA9053: flexible system level PMIC with multicore support
 dlg,da9063		DA9063: system PMIC for quad-core application processors
 domintech,dmard09	DMARD09: 3-axis Accelerometer
 domintech,dmard10	DMARD10: 3-axis Accelerometer
-epson,rx8010		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
-epson,rx8581		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
-emmicro,em3027		EM Microelectronic EM3027 Real-time Clock
 fsl,mag3110		MAG3110: Xtrinsic High Accuracy, 3D Magnetometer
 fsl,mma7660		MMA7660FC: 3-Axis Orientation/Motion Detection Sensor
 fsl,mma8450		MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer
@@ -53,9 +46,6 @@ gmt,g751		G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire In
 infineon,slb9635tt	Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz)
 infineon,slb9645tt	Infineon SLB9645 I2C TPM (new protocol, max 400khz)
 infineon,tlv493d-a1b6	Infineon TLV493D-A1B6 I2C 3D Magnetic Sensor
-isil,isl1208		Intersil ISL1208 Low Power RTC with Battery Backed SRAM
-isil,isl1218		Intersil ISL1218 Low Power RTC with Battery Backed SRAM
-isil,isl12022		Intersil ISL12022 Real-time Clock
 isil,isl29028		Intersil ISL29028 Ambient Light and Proximity Sensor
 isil,isl29030		Intersil ISL29030 Ambient Light and Proximity Sensor
 maxim,ds1050		5 Bit Programmable, Pulse-Width Modulator
@@ -142,7 +132,6 @@ microchip,mcp4662-503	Microchip 8-bit Dual I2C Digital Potentiometer with NV Mem
 microchip,mcp4662-104	Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k)
 microchip,tc654		PWM Fan Speed Controller With Fan Fault Detection
 microchip,tc655		PWM Fan Speed Controller With Fan Fault Detection
-microcrystal,rv3029	Real Time Clock Module with I2C-Bus
 miramems,da226		MiraMEMS DA226 2-axis 14-bit digital accelerometer
 miramems,da280		MiraMEMS DA280 3-axis 14-bit digital accelerometer
 miramems,da311		MiraMEMS DA311 3-axis 12-bit digital accelerometer
@@ -156,25 +145,12 @@ nuvoton,npct601		i2c trusted platform module (TPM2)
 nuvoton,w83773g		Nuvoton Temperature Sensor
 nxp,pca9556		Octal SMBus and I2C registered interface
 nxp,pca9557		8-bit I2C-bus and SMBus I/O port with reset
-nxp,pcf2127		Real-time clock
-nxp,pcf2129		Real-time clock
-nxp,pcf8523		Real-time Clock
-nxp,pcf8563		Real-time clock/calendar
-nxp,pcf85063		Tiny Real-Time Clock
 oki,ml86v7667		OKI ML86V7667 video decoder
 ovti,ov5642		OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus
-pericom,pt7c4338	Real-time Clock Module
 plx,pex8648		48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch
 pulsedlight,lidar-lite-v2	Pulsedlight LIDAR range-finding sensor
-ricoh,r2025sd		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,r2221tl		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rs5c372a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rs5c372b		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rv5c386		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rv5c387a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 samsung,24ad0xd1	S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
 sgx,vz89x		SGX Sensortech VZ89X Sensors
-sii,s35390a		2-wire CMOS real-time clock
 silabs,si7020		Relative Humidity and Temperature Sensors
 skyworks,sky81452	Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply
 st,24c256		i2c serial eeprom  (24cxx)
-- 
2.19.1

Re: [PATCH 2/2] dt-bindings: rtc: Move trivial RTCs to rtc.txt

From: Rob Herring <robh@kernel.org>
Date: 2018-12-03 23:46:02

On Sun, Nov 11, 2018 at 08:31:14PM +0100, Alexandre Belloni wrote:
Move trivial RTCs to the rtc generic binding documentation as they all also
support at least 'start-year'.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 Documentation/devicetree/bindings/rtc/rtc.txt | 34 +++++++++++++++++++
 .../devicetree/bindings/trivial-devices.txt   | 24 -------------
 2 files changed, 34 insertions(+), 24 deletions(-)
Okay if I take these 2 to avoid conflicts with trivial-devices.txt?

Rob

Re: [PATCH 2/2] dt-bindings: rtc: Move trivial RTCs to rtc.txt

From: Alexandre Belloni <alexandre.belloni@bootlin.com>
Date: 2018-12-04 00:04:45

On 03/12/2018 17:45:58-0600, Rob Herring wrote:
On Sun, Nov 11, 2018 at 08:31:14PM +0100, Alexandre Belloni wrote:
quoted
Move trivial RTCs to the rtc generic binding documentation as they all also
support at least 'start-year'.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 Documentation/devicetree/bindings/rtc/rtc.txt | 34 +++++++++++++++++++
 .../devicetree/bindings/trivial-devices.txt   | 24 -------------
 2 files changed, 34 insertions(+), 24 deletions(-)
Okay if I take these 2 to avoid conflicts with trivial-devices.txt?
Sure, I was actually planning for them to go through your tree for this
reason.

-- 
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH 1/2] dt-bindings: rtc: add generic bindings

From: Geert Uytterhoeven <geert@linux-m68k.org>
Date: 2018-12-06 10:37:15

Hi Alexandre,

On Sun, Nov 11, 2018 at 8:31 PM Alexandre Belloni
[off-list ref] wrote:
Add generic binding documentation for the RTC subsystem.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Thanks for your patch!
quoted hunk
new file mode 100644
index 000000000000..221b7da50aca
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -0,0 +1,30 @@
+The following properties may not be supported by all drivers. However, if a
+driver wants to support one of the below features, it should adapt the bindings
+below.
+- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
Can this resistor be less than 1 ohm?
trickle-resistor-milli-ohms?
+                          if trickle charger should be enabled
+- trickle-diode-disable : Do not use internal trickle charger diode Should be
+                          given if internal trickle charger diode should be
+                          disabled
+- wakeup-source :         Enables wake up of host system on alarm
Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH 1/2] dt-bindings: rtc: add generic bindings

From: Alexandre Belloni <alexandre.belloni@bootlin.com>
Date: 2018-12-07 09:34:10

On 06/12/2018 11:36:59+0100, Geert Uytterhoeven wrote:
quoted
+The following properties may not be supported by all drivers. However, if a
+driver wants to support one of the below features, it should adapt the bindings
+below.
+- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
Can this resistor be less than 1 ohm?
trickle-resistor-milli-ohms?
Well, this is what current drivers already use so we are stuck with that
for now.

The value should be a few kOhm anyway. I think the lowest I know about
is 250 Ohm.
quoted
+                          if trickle charger should be enabled
+- trickle-diode-disable : Do not use internal trickle charger diode Should be
+                          given if internal trickle charger diode should be
+                          disabled
+- wakeup-source :         Enables wake up of host system on alarm
Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds
-- 
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH 1/2] dt-bindings: rtc: add generic bindings

From: Geert Uytterhoeven <geert@linux-m68k.org>
Date: 2018-12-07 09:47:50

Hi Alexandre,

On Fri, Dec 7, 2018 at 10:34 AM Alexandre Belloni
[off-list ref] wrote:
On 06/12/2018 11:36:59+0100, Geert Uytterhoeven wrote:
quoted
quoted
+The following properties may not be supported by all drivers. However, if a
+driver wants to support one of the below features, it should adapt the bindings
+below.
+- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
Can this resistor be less than 1 ohm?
trickle-resistor-milli-ohms?
Well, this is what current drivers already use so we are stuck with that
for now.

The value should be a few kOhm anyway. I think the lowest I know about
is 250 Ohm.
OK, good to know. Thanks!

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help