Re-submission of arcxcnn backlight driver addressing the naming convention
concerns raised by Rob H. Note that all the device tree properties are
determined by the board design or IC EPROM settings and are not intended
to be user adjustable.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olimpiu Dejeu <redacted>
---
.../bindings/leds/backlight/arcxcnn_bl.txt | 31 ++++++++++++++++++++++
1 file changed, 31 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+ See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+ See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0: setting for register ILED_CONFIG_0
+- arc,led-config-1: setting for register ILED_CONFIG_1
+- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config: setting for register CONFIG_COMP
+- arc,filter-config: setting for register FILTER_CONFIG
+- arc,trim-config: setting for register IMAXTUNE
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+ compatible = "arc,arc2c0608";
+ reg = <0x30>;
+ default-brightness = <500>;
+ label = "lcd-backlight";
+ linux,default-trigger = "backlight";
+ led-sources = <0 1 2 5>;
+};
+--
2.7.4
Your subject should look something like [PATCH vX 0/Y]
Where X is the number of times you've submitted this set.
On Fri, 18 Nov 2016, Olimpiu Dejeu wrote:
Re-submission of arcxcnn backlight driver addressing the naming convention
concerns raised by Rob H. Note that all the device tree properties are
determined by the board design or IC EPROM settings and are not intended
to be user adjustable.
This is a change log, not a commit log.
Here is where you tell us about the patch.
Read: Documentation/SubmittingPatches
Documentation/SubmitChecklist
... before submitting again.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olimpiu Dejeu <redacted>
---
In here (below the ---) you should have a change log which looks like
this:
v3 => v4:
- The changes you made
v2 => v3:
- The changes you made
v1 => v2:
- The changes you made
... etc
quoted hunk
.../bindings/leds/backlight/arcxcnn_bl.txt | 31 ++++++++++++++++++++++
1 file changed, 31 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
new file mode 100644
index 0000000..a7b6ff2
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -0,0 +1,33 @@
+Binding for ArcticSand arc2c0608 LED driver
+
+Required properties:
+- compatible: should be "arc,arc2c0608"
+- reg: slave address
+
+Optional properties:
+- default-brightness: brightness value on boot, value from: 0-4095
+- label: The name of the backlight device
+ See Documentation/devicetree/bindings/leds/common.txt
+- led-sources: List of enabled channels from 0 to 5.
+ See Documentation/devicetree/bindings/leds/common.txt
+
+- arc,led-config-0: setting for register ILED_CONFIG_0
+- arc,led-config-1: setting for register ILED_CONFIG_1
+- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arc,comp-config: setting for register CONFIG_COMP
+- arc,filter-config: setting for register FILTER_CONFIG
+- arc,trim-config: setting for register IMAXTUNE
+
+Note: Optional properties not specified will default to values in IC EPROM
+
+Example:
+
+arc2c0608@30 {
+ compatible = "arc,arc2c0608";
+ reg = <0x30>;
+ default-brightness = <500>;
+ label = "lcd-backlight";
+ linux,default-trigger = "backlight";
+ led-sources = <0 1 2 5>;
+};
+
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog