[PATCH] ARM: dts: sun8i: Base Orange Pi Plus dts on the Orange Pi 2 dts

@@ -40,61 +40,13 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+/* The Orange Pi Plus is an extended version of the Orange Pi 2 */
+#include "sun8i-h3-orangepi-2.dts"
 
 / {
 	model = "Xunlong Orange Pi Plus";
 	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
 
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
-
-		status_led {
-			label = "orangepi-plus:red:status";
-			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr_led {
-			label = "orangepi-plus:green:pwr";
-			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
-	};
-
-	r_gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
-
-		sw2 {
-			label = "sw2";
-			linux,code = <BTN_1>;
-			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
-		};
-
-		sw4 {
-			label = "sw4";
-			linux,code = <BTN_0>;
-			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-		};
-	};
-
 	reg_usb3_vbus: usb3-vbus {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";

@@ -106,49 +58,12 @@
 		enable-active-high;
 		gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
 	};
-
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
-	};
-};
-
-&ehci1 {
-	status = "okay";
 };
 
 &ehci3 {
 	status = "okay";
 };
 
-&ir {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
-	status = "okay";
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
-	status = "okay";
-};
-
-&mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
-	vmmc-supply = <&reg_vcc3v3>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	bus-width = <4>;
-	non-removable;
-	status = "okay";
-};
-
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;

@@ -167,13 +82,6 @@
 };
 
 &pio {
-	leds_opc: led_pins@0 {
-		allwinner,pins = "PA15";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
 	usb3_vbus_pin_a: usb3_vbus_pin@0 {
 		allwinner,pins = "PG11";
 		allwinner,function = "gpio_out";

@@ -182,46 +90,6 @@
 	};
 };
 
-&r_pio {
-	leds_r_opc: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	sw_r_opc: key_pins@0 {
-		allwinner,pins = "PL3", "PL4";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
-		allwinner,pins = "PL7";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-};
-
-&reg_usb1_vbus {
-	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&usb1_vbus_pin_a {
-	allwinner,pins = "PG13";
-};
-
 &usbphy {
-	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb3_vbus-supply = <&reg_usb3_vbus>;
-	status = "okay";
 };